SAB Heli Division Goblin 570 User Manual - page 18
Some example configurations:
Performance
Battery
Pinion
ESC
RPM Max
Pitch
6S
3300/4500
Scorpion
HKIII4025-1100
Quantum
4125-1100
EDGE 130
19T
SET RPM
± 12,5
2450
6S
3300/4500
Pyro 600-1200
CC Talon 90
18T / 19T / 20T
2600 / 2700 / 2850 ± 12,5
Jive 100LV
YGE 120 LV
Koby 90
YGE 100 LV
17T
16T
18T
Gov @ 80%
Gov @ 80%
SET RPM
Quantum
4120-1200
Scorpion
HK4020-1100
Scorpion
HK4020-1350
Savox
BMS 4750-1200
Jive 100LV
YGE 120 LV
Jive 100LV
YGE 120 LV
CC Talon 90
Jive 100LV
YGE 120 LV
CC Talon 90
Jive 100LV
YGE 120 LV
CC Talon 90
Jive 100LV
YGE 120 LV
CC Talon 90
17T / 18T / 19T
18T / 19T / 20T
16T / 17T / 18T
18T / 19T / 20T
17T / 18T / 19T
17T / 18T / 19T
Gov @ 80%
SET RPM
Gov @ 80%
SET RPM
Gov @ 80%
Gov @ 80%
SET RPM
Gov @ 80%
SET RPM
SET RPM
Note: Although the Goblin can fly at high RPM, for safety reasons we recommend not exceeding 2600 RPM.
Motor
TRANSMISSION SETUP
It is important to choose the right reduction ratio to maximize efficiency based on your required flight performance.
The Goblin has many possible reduction ratios at your disposal. It is possible to optimize any moror and battery combination. It is
recommended to use wiring and connector appropriate for the currents generated in a helicopter of this class.
If you are using a head speed calculator which requires a main gear and pinion tooth count, use 206 teeth for main gear (this takes
into account the two stage reduction) and the tooth count of your pulley as the pinion count.
Below is a list of available reduction ratios:
H0215-16-S-16T Pinion = ratio 12.9:1 H0215-20-S-20T Pinion = ratio 10.3:1
H0215-17-S-17T Pinion = ratio 12.2:1 H0215-21-S-21T Pinion = ratio 9.8:1
H0215-18-S-18T Pinion = ratio 11.5:1 H0215-22-S-22T Pinion = ratio 9.4:1
H0215-19-S-19T Pinion = ratio 10.9:1 H0215-23-S-23T Pinion = ratio 9:1
H0215-24-S-24T Pinion = ratio 8.5:1
These are pulleys for motors with a 6 mm shaft. Each pulley includes an adapter for motors with a 5 mm shaft.
19T / 20T / 21T
18T / 19T / 20T
15T / 16T / 17T
EDGE 130
6S - 5500
(5000 / 5500)
Scorpion
HKIII4025-1100
EDGE 130
22T / 23T
2350 / 2450
± 12,5
Jive 100LV
YGE 120 LV
21T / 22T
Quantum
4125-1100
EDGE 130
22T / 23T
Jive 100LV
YGE 120 LV
21T / 22T
Kontronik Pyro
650-1150
EDGE 130
21T / 22T
Jive 100LV
YGE 120 LV
20T / 21T
12S - 3000
(2600 / 3300)
Quantum
4125-560
Scorpion
HKIII 4025-550
EDGE 80 HV
22T / 23T
2400 / 2500
± 12,5
Jive 80 HV
YGE 90 HV
21T / 22T
Quantum
4125-560
Scorpion
HKIII 4025-550
EDGE 120 HV
22T / 23T / 24T
2400 / 2500 / 2600
Jive 120 HV
YGE 120 HV
21T / 22T / 23T
Kontronik Pyro
650-620
EDGE 80 HV
20T / 21T
2400 / 2500
Jive 80 HV
YGE 90 HV
19T / 20T
Pyro Competition
650-620
EDGE 120 HV
20T / 21T / 22T
2400 / 2500 / 2620
Jive 120 HV
YGE 120 HV
19T / 20T / 21T
Copyright © 2014 - SAB Heli Division - All rights reserved
Page 16
Chapter 9, Installation Of the Motor