- DL manuals
- Salus
- Thermostat
- EP101
- Instruction manual
Salus EP101 Instruction manual
Summary of EP101
Page 1
Instruction manual model no ep101 programmable heating controller 2 salus ep101 manual 001:89 21/11/10 11:49 page 1.
Page 2
Salus ep101 manual 001:89 21/11/10 11:49 page 2.
Page 3: Product Compliance
Product compliance this product complies with the essential requirements of the following ec directives: • electro-magnetic compatibility directive 2004/108/ec • low voltage directive 2006/95/eec • ec marking directive 93/68/eec safety information these instructions are applicable to the salus contr...
Page 4: Introduction
Introduction a a programmable heating controller is used to switch the heating system in your home on and off as needed. It works by controlling the heating boiler according to a series of programmed settings that take effect at different times of the day. The ep101 from salus controls is a stylish ...
Page 5: Installation
Installation please read the important safety information at the start of this manual before you begin to install the device. The ideal position to locate the ep101 programmable heating controller is about 1.5m above floor level. It should be mounted in a location where the controller is easily acce...
Page 6: Volt Free Switching
After installing the backplate in a suitable location, wiring connections can be made as shown above. The following criteria apply to the installation: • the incoming ac mains supply should be 230v ac and fused at 6 amps. • optimum cable size for installation is 1.5 mm2; wiring colours should be in ...
Page 7: Jumper Settings
Jumper settings changes to the jumper settings should only be made by the engineer carrying out the installation or other qualified person. The installer should select the jumper positions required if changes need to be made to the factory default settings. These jumpers are found on the rear of the...
Page 8: After Installation
After installation after completing installation and powering up the ep101 for the first time the controller will behave in the following way: all the indicators on the display and the backlight will be turned on for two seconds. After two seconds, the ep101 will then operate in normal mode (control...
Page 9: User Interface and Controls
User interface and controls the status and operation of the ep101 can be clearly seen on the large backlit liquid crystal display (lcd) - this display allows the user to see at a glance the current status of the heating system. There are few user controls for the ep101, making the controller very ea...
Page 10: Operation
Operation the ep101 is configured and adjusted by the use of an intuitive user interface with a minimal number of user controls. The backlit lcd gives a highly visible, easily readable indication of the controller status. Setting the time press and hold set and select when the ep101 is in normal mod...
Page 11
Pressing and releasing select again will then display the year as displayed press the up or down keys to increase or decrease the year – valid settings are between 05 and 99 (indicating a year range of 2005 to 2099). Press the select key to select the month section of the date – this is adjusted in ...
Page 12: Programming The Ep101
Programming the ep101 the ep101 offers great versatility with its programming options, allowing the user to programme the unit to operate on a 5/2 or 7 day control cycle. The controller has a default set of programmes that have been designed to meet the needs of most users. If these default programm...
Page 13
Press the select key to confirm the weekday or weekend selection. Once this is set, the ‘hour’ will flash to indicate that it is the selected item and is the next item to be adjusted: press the up or down key to adjust the hour setting to the desired value, and confirm your selection by pressing the...
Page 14
7 day mode the ep101 also offers a 7 day programming mode, which allows you to programme three different sets of on/off times for each day of the week to give a total of 21 separate programme settings. To review or change a programme, press the set key when the ep101 is in normal mode. This will cha...
Page 15
Pressing the select key allows you to step through each of the items to be reviewed or adjusted within the programmes in the following sequence: programme status function sequence 1 on hour minutes 1 off hour minutes 2 on hour minutes 2 off hour minutes 3 on hour minutes 3 on hour minutes …before th...
Page 16: Operating Mode Selection
Operating mode selection the ep101 operating mode is selected by pressing the mode key. There are four operating modes for the controller: on, once, auto and off the mode can be changed when the controller is in normal mode by pressing the mode key. Each key press will cycle the operation mode as fo...
Page 17: Holiday Override Mode
Holiday override mode the holiday override mode allows the user to override all the current programme settings and turn off the heating for up to 31 days. When the ep101 is in normal mode, pressing the backlight/holiday key for 3 seconds or longer allows you to turn on the holiday override mode. The...
Page 18: Temporary Override Mode
Temporary override mode the temporary override mode allows the user to override the current programme settings and turn the heating on for a preset period. This mode is activated by pressing the +1hr key. After pressing the +1hr key, the controller display will change have the day numeral flashing t...
Page 19: Other Functions and Controls
Other functions and controls backlight the backlight of the ep101 is switched on automatically whenever any of the keys are pressed. The backlight will remain illuminated for approximately 5 seconds after the last key press, except if you are changing settings within the clock, programme or temporar...
Page 20: Maintenance
Maintenance the ep101 programmable heating controller requires no special maintenance. Periodically, the outer casing can be wiped clean using a dry cloth (please do not use solvents, polishes, detergents or abrasive cleaners, as these can damage the thermostat). There are no user serviceable parts ...
Page 21: Product Specification
Product specification model: ep101 type: programmable heating controller designed for 230v ac and volt free heating applications. Programming programming modes: user selectable for 5/2 or 7 day option number of programmes: three (3) user programmes plus factory default programme. Override facility: ...
Page 22
Salus controls warrants that this product will be free from any defect in materials or workmanship, and shall perform in accordance with its specification, for a period of two years from the date of purchase. Salus controls sole liability for breach of this warranty will be (at its option) to repair...
Page 23
Salus ep101 manual 001:89 21/11/10 11:49 page 23.
Page 24: Sales
Email: sales@salus-tech.Com tel: 01226 323961 email: tech@salus-tech.Com tel: 01226 323961 sales : technical : salus controls plc, salus house, dodworth business park south, whinby road, dodworth, barnsley s75 3sp salus-tech. Salus ep101 manual 001:89 21/11/10 11:49 page 24.