- DL manuals
- Sam4s
- Cash Register
- ER-430M
- Operation And Program Manual
Sam4s ER-430M Operation And Program Manual
Summary of ER-430M
Page 1
Er-430m electronic cash register au operation and program manual all specificaitons are subject to change without notice jk68-60964i(rev.03) from er-430m v1.0 up to v2.7.
Page 2
Attention the product that you have purchased contains a rechargeable ni-mh battery. This battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of the battery into the municipal waste system. Check with your local solid waste officials...
Page 3: Precaution Statements
Precaution statements follow these safety, servicing and esd precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 safety precautions 1. Be sure that all built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstall...
Page 4
1-2 servicing precautions warning: first read the-safety precautions-section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning: an electrolytic capacitor installed with the wrong polarity mig...
Page 5: Contents
Er430m electronic cash register au contents • i contents getting started 1 about the er-430m................................................................................................................... 1 unpacking....................................................................................
Page 6
Ii • contents er430m electronic cash register au code plu entry - multiplication ..............................................................................29 code plu entry - multiplication with decimal point ..............................................29 code plu entry - split pricing ..........
Page 7
Er430m electronic cash register au contents • iii x/z mode 69 introduction ............................................................................................................................. 69 x/z reports .......................................................................................
Page 8
Iv • contents er430m electronic cash register au print option table ...................................................................................................108 function key programming...................................................................................................112 pr...
Page 9
Er430m electronic cash register au contents • v program 701 - financial report message programming ........................................ 157 program 710 - clerk report message programming .............................................. 159 program 711 - macro name programming ........................
Page 11: Getting Started
Er430m electronic cash register au getting started • 1 getting started about the er-430m • the er-430m features a 90-position keyboard with hospitality friendly flat keys. This keyboard will accommodate up to 60 nlu keys and works best in retail stores, or shops where it is not necessary to place a ...
Page 12: Unpacking
2 • contents er430m electronic cash register au unpacking 1. Unpack and unwrap the cash register. 2. Located in the packing are the following items: • 2 rolls of paper and 1 paper spindle, • 2 sets of control keys, • operation and program manual, 3. Remove the cardboard protectors from the cash draw...
Page 13
Er430m electronic cash register au getting started • 3 2. For proper feeding through the print head, cut or tear a straight even edge on the end of the paper roll. (be sure to remove any paper with glue residue.) place the paper roll in the paper holder so that the paper will feed from the bottom of...
Page 14
4 • contents er430m electronic cash register au 4. Close the paper lever and press the paper feed key until the paper comes out. 5. Passing the leading edge of the paper through the cutter slot. Tear off the excess paper. Replace the printer cover..
Page 15
Er430m electronic cash register au getting started • 5 ※ if you wish to use the printer to print a sales journal, insert the paper into the paper take-up spool. Wind the paper two or three turns around the spool shaft and install the spool in the mount. ※ er-430m is possible to feed automatically wh...
Page 16: Basic Features and Functions
6 • contents er430m electronic cash register au basic features and functions standard hardware • display: 2 line, 16 character liquid crystal display and ten position rear displays with a rear pop up display standard. • 90-position flat keyboard. • 2 station thermal 24-column printer with drop-and-p...
Page 17: Register
Er430m electronic cash register au getting started • 7 front display the er-430m comes with a liquid crystal screen, allowing you to view up to 2 lines of information with up to 16 characters per line. The display is backlit and to provide excellent visibility, regardless of lighting conditions. Whe...
Page 18
8 • contents er430m electronic cash register au rear display the rear display is a 10 digit florescent display that allows your customer to monitor the transaction and view the sale total. The rear display can be lifted and turned for easy customer viewing. Rear display information item count the nu...
Page 19
Er430m electronic cash register au getting started • 9 total of sale numbered error conditions.
Page 20
10 • contents er430m electronic cash register au error code table e00 sequence error e23 consol over e01 plu no data e24 req. Subtotal e02 clerk error e25 promo error e03 amount count over e26 check open e04 lan tran e27 req. Password e05 communication error e28 no void plu e06 time and date e29 232...
Page 21
Er430m electronic cash register au getting started • 11 control lock the control lock has 7 positions, accessed with 5 keys. Each ecr is shipped with two full sets of keys. Void p z x reg off s void use to void (correct) items outside of a sale. Off the register is inoperable. Reg use for normal reg...
Page 22
12 • contents er430m electronic cash register au keyboards the er-430 keyboard includes 90 key positions with the default legends and key assignments as shown below. This configuration has 60 keyboard nlu locations. The keyboard legend sheet can be replaced by lifting the protective plastic cover. P...
Page 23: Memory Clear
Er430m electronic cash register au getting started • 13 memory clear memory all clear (ram clear) caution: the procedures described in this area are security sensitive. Clearing all or parts of the er-430m memory may cause damage or loss to the program. Do not share this information with unauthorize...
Page 24
14 • contents er430m electronic cash register au initial clear (status clear) caution: do not share this information with unauthorized users. Distribute the p mode key only to those you may want to perform this function. The initial clear function allows you to exit any register activity and return ...
Page 25: Operating Instructions
Er430m electronic cash register au operating instructions • 15 operating instructions function key descriptions keys are listed in alphabetical order. Some of the keys described below are not included on the default keyboard. See “function key assignment programming” to add or change programmable ke...
Page 26
16 • contents er430m electronic cash register au keyboard legend description charge (1 - 8) or eftpos use to finalize charge sales. Calculates the sale total including tax, finalizes the sale, and opens the cash drawer. Change computation is allowed by entering an amount before pressing the charge k...
Page 27
Er430m electronic cash register au operating instructions • 17 keyboard legend description guest # use to enter the count of guests served as part of a guest check. Inactive use to inactivate the key on the keyboard with warning/error message. Jfeed (journal feed) advances the journal printer paper ...
Page 28
18 • contents er430m electronic cash register au keyboard legend description tare tares are container weights. If you are using the scale function, you can preset up to 5 different tare weights. The tare can be subtracted automatically when a specific plu is registered, or manually inputting the tar...
Page 29: Clerk Sign-On/sign-Off
Er430m electronic cash register au operating instructions • 19 clerk sign-on/sign-off see "system option programming” to review your clerk options: • system option #2 allows you to select direct or code entry sign on. • system option #3 allows you to select stay-down or pop-up operation. Depending o...
Page 30: Receipt On and Off
20 • contents er430m electronic cash register au receipt on and off the receipt on/off function key may or may not be located on your keyboard. If the receipt on/off key is located on the keyboard 1. Press the receipt on/off key once to turn the receipt off. 2. Press the receipt on/off key again to ...
Page 31: Item Registrations
Er430m electronic cash register au operating instructions • 21 item registrations all registrations on er-430m are made into open or preset plus. • in place of traditional plu keys, some plus are located directly on the keyboard. • when more items or categories are needed than the number of plus ava...
Page 32
22 • contents er430m electronic cash register au keyboard plu entry - open price / preset price override 1. Enter an amount on the number pad. Do not use the decimal key. For example, for $2.99, enter: 2 9 9 2. Press a plu. For example, press plu 1: 1 receipt example: thank-you call again date 15/01...
Page 33
Er430m electronic cash register au operating instructions • 23 keyboard plu entry - repeat open or preset price plus can be repeated as many times as necessary by pressing the same plu again. The number of times the item is repeated is shown on the display. 1. Enter an amount on the number pad. Do n...
Page 34
24 • contents er430m electronic cash register au keyboard plu entry - multiplication when several of the same items are to be entered into the same plu, you can use multiplication. You can enter a quantity (1 to 999.999) using the x/time key. You can multiply open or preset plus. 1. Enter the quanti...
Page 35
Er430m electronic cash register au operating instructions • 25 keyboard plu entry - multiplication with decimal point if you are selling items by weight or by length etc., you can multiply a fraction of a unit. It is up to 3 digits after decimal places. 1. Enter the amount with the decimal point, an...
Page 36
26 • contents er430m electronic cash register au keyboard plu entry - split pricing when items are priced in groups, i.E. 3 for $1.00, you can enter the quantity purchased and let the register calculate the correct price. 1. Enter the quantity purchased, and then press the x/time key. For example, e...
Page 37
Er430m electronic cash register au operating instructions • 27 code plu entry - open price if the preset status of a plu is set to n (no), the plu will operate as an open price plu. See "plu programming" in the "program mode programming" chapter to program plu descriptors and options. 1. Enter the p...
Page 38
28 • contents er430m electronic cash register au code plu entry - preset price override if the override preset is set to y (yes), the plu is operating as a preset override plu. See "plu programming" in the "program mode programming" chapter to program plu descriptors and options. 1. Enter the quanti...
Page 39
Er430m electronic cash register au operating instructions • 29 code plu entry - multiplication when several of the same items are to be entered into the same plu, you can use multiplication. You can enter a quantity (1 to 999.999) using the x/time key. You can multiply open or preset plus. 1. Enter ...
Page 40
30 • contents er430m electronic cash register au code plu entry - split pricing when items are priced in groups, i.E. 3 for $1.00, you can enter the quantity purchased and let the register calculate the correct price. 1. Enter the quantity purchased, and then press the x/time key. For example, enter...
Page 41
Er430m electronic cash register au operating instructions • 31 barcode plu entry - open price, single item 1. Press 1 on the number pad, and then press the x/time key. 1 x/ ti me 2. Scan barcode of the item. 3. Enter an amount on the number pad. Do not use the decimal key. For example, for $2.99, en...
Page 42
32 • contents er430m electronic cash register au barcode plu entry - preset price override, single item 1. Press 1 on the number pad, and then press the x/time key. 1 x/ ti me 2. Scan barcode of the item. 3. Enter an amount on the number pad. Do not use the decimal key. For example, for $2.99, enter...
Page 43
Er430m electronic cash register au operating instructions • 33 modifier key pressing a modifier key alters the next plu registered, either by changing the code number of the plu so that a different item is registered, or by just adding the modifier descriptor and registering the same plu. See "modif...
Page 44
34 • contents er430m electronic cash register au price level key if you choose to use the price level feature, you must allocate memory for each level. See "memory allocation" in the "service mode programming" chapter. Note that the default program selects one price level. You must also place price ...
Page 45
Er430m electronic cash register au operating instructions • 35 promo the promo key allows you to account for promotional items, as in "buy two, get one free". Pressing this key will remove an item's cost from the sale, and the promo item will not be added to the plu sales total, but it is added to t...
Page 46
36 • contents er430m electronic cash register au waste the waste key allows control of inventory by accounting for items that must be removed from stock due to spoilage, breakage or mistakes. Press the waste key before entering wasted items, and then press the waste key again to finalize. The waste ...
Page 47: Percent Key Operations
Er430m electronic cash register au operating instructions • 37 percent key operations a total of five % functions are available. %1 is located on the default keyboard. Your keyboard may be different. More or less % keys may be located on the keyboard, or they may be located on one of the function lo...
Page 48
38 • contents er430m electronic cash register au preset percent discount on an item in this example the %1 function is programmed with percentage, negative, item, preset and overridable witha rate of 10%.Please refer to % (1 ~ 5) (discounts or surcharges) in function key programming in program mode ...
Page 49
Er430m electronic cash register au operating instructions • 39 preset percent discount on sale total in this example the %1 function is programmed with percentage, negative, sale, preset and overridable witha rate of 10%.Please refer to % (1 ~ 5) (discounts or surcharges) in function key programming...
Page 50
40 • contents er430m electronic cash register au dollar amount discount on sale when programmed as "amount", "sale", "open" and "negative", a % key will deduct an amount from a sale. Also, depending upon programming: • you may be allowed to enter only one discount in a sale, after the sbtl key is pr...
Page 51
Er430m electronic cash register au operating instructions • 41 return merchandise registrations if you wish to return or refund an item press return, then re-enter any item. You can return merchandise as part of a sale, or you can return merchandise as a separate transaction and return cash to the c...
Page 52: Voids and Corrections
42 • contents er430m electronic cash register au voids and corrections error correction (void last item) this function corrects the last item entered. 1. Register the item you wish to sell. 2. Press the error corr key: error corr receipt example: thank-you call again date 15/01/2003 wed time 08:33 p...
Page 53
Er430m electronic cash register au operating instructions • 43 cancel the cancel key allows you to stop any transaction. Anything registered within the transaction before the cancel key is pressed is automatically corrected. The cancel key can be inactivated through programming, see "function key pr...
Page 54: No Sale Operations
44 • contents er430m electronic cash register au no sale operations open drawer the #/no sale key will open the cash drawer when you have not already started a transaction. The no sale function can be disabled or placed under manager control through programming, see "function key programming" in the...
Page 55
Er430m electronic cash register au operating instructions • 45 received on account operations you can use one of the received on accountfunctions (ra1-ra3) to accept cash or checks into the cash drawer when you are not actually selling merchandise. For example, use received on accountto accept payme...
Page 56: Paid Out Operations
46 • contents er430m electronic cash register au paid out operations you can use the paid out function (po1-po3) to track cash or checks paid out or to record loans from the cash drawer. 1. Press one of the paid out keys (po1-po3) po1 2. Enter the amount of cash paid out, press cash. C as h 0 0 0 1 ...
Page 57: Subtotaling A Sale
Er430m electronic cash register au operating instructions • 47 subtotaling a sale 1. Register the items you wish to sell. 2. Press sbtl. The subtotal will display with the message "sub" indicated on the rear display. Sbt l the subtotal can be printed if the system option is set. See "print option pr...
Page 58: Totaling and Tendering
48 • contents er430m electronic cash register au totaling and tendering there are ten tender functions available to categorize sales. Cash and check are individual keys on the keyboard totaling a cash sale 1. Register the items you wish to sell. 2. To total a cash sale, press cash: cash 3. The displ...
Page 59
Er430m electronic cash register au operating instructions • 49 tendering a cash sale 1. Register the items you wish to sell. 2. Enter the amount tendered by the customer. For example, for $20.00 enter: 0 0 0 2 3. Press cash: cash 4. The display will indicate the total amount of the cash tendered and...
Page 60
50 • contents er430m electronic cash register au totaling a charge (eftpos) sale use the charge keys to track charge or credit card sales. See "function key programming" in the "program mode programming" chapter to change the descriptors for the charge tender functions. For example, you can use char...
Page 61
Er430m electronic cash register au operating instructions • 51 cash out within a charge (eftpos) sale cash out within a charge (eftpos) sale may or may not be allowed. See "function key assignment programming" in the "service mode programming" chapter to assign cash out key. 1. Register the items yo...
Page 62
52 • contents er430m electronic cash register au check cashing check cashing means exchanging cash for a check. If you wish to cash checks, you must place a chkcash key on the keyboard. See "function key assignment" in the "program mode programming" chapter. 1. Enter the amount of the check tendered...
Page 63
Er430m electronic cash register au operating instructions • 53 post tender post tendering means computing change after the sale has been totaled and the drawer is open. This feature is useful when a customer changes the amount of the tender or when a "quick change artist" confuses a clerk. Normally,...
Page 64
54 • contents er430m electronic cash register au table management and clerk interrupt operations overview the er-430m can employ a manual previous balance, hard check (monthly accounts), or soft check (restaurant bill) system. (you must select hard or soft check posting in memory allocation programm...
Page 65
Er430m electronic cash register au operating instructions • 55 soft check - restaurant style billing opening a soft check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, press the check # key to automatically assign a check: check# 2. If required, enter the table numb...
Page 66
56 • contents er430m electronic cash register au adding to a soft check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, if you entered a table number, enter the table number and press the table key: t able 3 2. Register the next items you wish to sell. 3. To total the...
Page 67
Er430m electronic cash register au operating instructions • 57 paying a soft check without payment key required to close check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, if you entered a table number, enter the table number and press the table key: t able 3 2. If...
Page 68
58 • contents er430m electronic cash register au taking deposits or account payments with payment key required to close check taking deposits or account payments, can only be done when the payment key is programmed as “required to close check=yes”. See “function key programming - payment” in “progra...
Page 69
Er430m electronic cash register au operating instructions • 59 paying a soft check with payment key required to close check taking deposits or account payments, can only be done when the payment key is programmed as “required to close check=yes”. See “function key programming - payment” in “program ...
Page 70
60 • contents er430m electronic cash register au hard check - monthly account style billing opening a hard check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 or, press the check # key to automatically assign a check: check# 2. Register the items you wish to sell. 3. Pl...
Page 71
Er430m electronic cash register au operating instructions • 61 paying a hard check without payment key required to close check 1. Enter the number of the guest check, press the check # key: check# 3 1 2 2. Pay the balance, as you would normally tender a transaction, with cash, check, or one of the c...
Page 72
62 • contents er430m electronic cash register au paying a hard check with payment key required to close check taking deposits or account payments, can only be done when the payment key is programmed as “required to close check=yes”. See “function key programming - payment” in “program mode programmi...
Page 73
Er430m electronic cash register au operating instructions • 63 sample of hard check postings printed on an optional cbm-820 printer example without payment key required to close check: date ___________ 15/01/2003 ____________ wed ____ check # _________________ #123 ____ pbal _______________________ ...
Page 74: Scale Entry
64 • contents er430m electronic cash register au scale entry direct scale entry place a product on the scale and access the scale function to display the weight on the cash register. Then make the appropriate entry; the plu must have "scalable" status. 1. Place an item on the scale. 2. Press the sca...
Page 75
Er430m electronic cash register au operating instructions • 65 automatic scale entry place a product on the scale and make the appropriate plu entry. The plu must be set with "auto scale status" & “scalable”. 1. Place an item on the scale. 2. Press a plu key, if the item is a preset item, or enter t...
Page 76
66 • contents er430m electronic cash register au manual tare weight entry 1. Place an item on the scale. 2. Enter the manual tare number, 5. Press the tare key: 5 t are 3. Enter the weight of the tare. For example, enter .01, press the tare key: 1 t are . 0 4. Press the scale key. Scale 5. Note that...
Page 77
Er430m electronic cash register au operating instructions • 67 manual weight entry operators can make manual weight entries if the item has been programmed to accept them. You must use the decimal key to enter fractional manual weights. 1. Place an item on the scale. 2. Enter the weight using the de...
Page 79: X/z Mode
Er430m electronic cash register au x/z mode • 69 x/z mode introduction all management functions take place with the control lock in the x position. In this way only those with the correct key will have access to these functions. Some register operations may be programmed to require the control lock ...
Page 80: X/z Reports
70 • contents er430m electronic cash register au x/z reports system reports are divided into two basic categories: • x reports (include x1 and x2 reports) in x mode, which read totals without resetting • z reports (include z1 and z2 reports) in z mode, which read totals and reset them to zero most r...
Page 81
Er430m electronic cash register au x/z mode • 71 report table report type report number report mode control lock position key sequence x1 x 1 – sbtl z1 z 1 – sbtl x2 x 201 – sbtl financial 1 z2 z 201 – sbtl x1 x 2 – sbtl z1 z 2 – sbtl x2 x 202 – sbtl time 2 z2 z 202 – sbtl x1 x 3 – sbtl z1 z 3 – sbt...
Page 82
72 • contents er430m electronic cash register au reset hard check (slip) line # (eprom v2.0 & later) if you want to reset hard check line # to 0, follow below sequence after turn control lock to z-mode. Program 10 - reset hard check line # programming 1. Reset all hard check line #. Cash 0 sbtl 0 1 ...
Page 83: Cash Declaration
Er430m electronic cash register au x/z mode • 73 cash declaration if compulsory cash declaration is required, you must declare the count of the cash drawer prior to taking x or z financial and clerk reports. You can enter the cash drawer total in one step, or to facilitate the counting of the cash d...
Page 85: Service Mode Programming
Er430m electronic cash register au service mode programming • 75 service mode programming overview the following procedures are done from the service mode menu: • program 20 - clear all sales totals • program 30 - clear grand total • program 40 - clear / delete plu file • program 50 - eprom informat...
Page 86: Memory Allocation Scan
76 • contents er430m electronic cash register au memory allocation scan 1. Turn the control lock to the s-mode to scan the allocated memory. 2. To scan memory allocation, enter 6 0, press the sbtl key. 0 sbtl 6 3. Press cash key cash pc online mode in er-430m, there are no special commands to enter ...
Page 87: Memory Allocation
Er430m electronic cash register au service mode programming • 77 memory allocation nb. This will clear the memory! Program 60 - memory allocation programming 1. Turn the control lock to the s-mode. 2. To allocate memory, enter 6 0, and then press the sbtl key. 0 sbt l 6 3. Refer to the chart below. ...
Page 88: Clear All Sales Totals
78 • contents er430m electronic cash register au clear all sales totals program 20 - clear all sales totals 1. Turn the control lock to the s-mode. 2. To clear all sales totals, enter 2 0, and then press the sbtl key. 0 sbt l 2 clear grand total program 30 - clear grand total 1. Turn the control loc...
Page 89
Er430m electronic cash register au service mode programming • 79 function key assignment programming function keys may be relocated, inactivated or changed with this program. For example, you may wish to place functions, such as previous balance and service that are not placed on the default keyboar...
Page 90
80 • contents er430m electronic cash register au function key codes code function code function code function code function 1 nlu 1 142 charge 1 168 level 1 194 rec on acct 2 100 nlu 100 143 charge 2 169 level 2 195 rec on acct 3 101~ reserved 144 charge 3 170 macro 1 196 sbtl 119 reserved 145 charg...
Page 91
Er430m electronic cash register au service mode programming • 81 rs232c serial ports communication options you must define the device that is attached to the rs-232c communications port, and the options for the device. The default is comm1 is set to pc polling program 8x - rs232c serial ports commun...
Page 92
82 • contents er430m electronic cash register au n1 option n2 value 0 none 1 pc 2 scale 3 rj* / cctv 4 receipt printer 6 scanner 7 coin 8 eft 5 device function (port1 is set to 1 pc as default; port2 is set to 0 none as default) (eprom v2.3) 9 pole 6 initial feeding line kp 0 – 20 0 7 end feeding li...
Page 93
Er430m electronic cash register au service mode programming • 83 n1 option n2 value 0 epson 12 pole display 1 icd 0 eft gled 1 eft inge 2 reserved 3 tyro eftpos (eprom v1.5) 13 eft type 4 eft nzinge (eprom v2.7) 14 eft config byte 0 – 127 0 0 none 1 dm 15 eft currency 2 euro 16 eft password 0- 99999...
Page 95: Program Mode Programming
Er430m electronic cash register au program mode programming • 85 program mode programming default programming • all keyboard plus are taxable, preset and override, without entry limits by default status programming of "40000000". • all system options are set to 0 in default programming, unless other...
Page 96
86 • contents er430m electronic cash register au descriptor programming methods descriptors are programmable for plus, function keys, groups, clerks and the logo/messages. There are two methods available to program descriptors, the alpha overlay and descriptor code methods. Alpha overlay method is t...
Page 97
Er430m electronic cash register au program mode programming • 87 descriptor code method if you customize your keyboard by covering key locations, or by installing double or quad size keys, you will need to program descriptors using the descriptor code method. Descriptor code chart char Ç ü é â ä à å...
Page 98: Tax Programming
88 • contents er430m electronic cash register au tax programming the er-430m has the capability to support four separate taxes. Taxes can be calculated as either a straight percentage rate of between .001% and 99.999%, or a 60 break point tax table. Each tax may be either an add-on tax (added to the...
Page 99
Er430m electronic cash register au program mode programming • 89 4. Enter 0 here for all taxes, unless you are programming tax 4 as a canadian gst. If tax 4 is a canadian gst, enter the sum of the options below: option value = sum gst (tax 4) is taxable by rate 1? Yes = 1 no = 0 gst (tax 4) is taxab...
Page 100: Plu Programming
90 • contents er430m electronic cash register au plu programming all plus, whether they are registered by pressing a plu key on the keyboard, or by entering the plu number and pressing the plu key, have the same programming options. These options are set through separate programs: • program 100 - pl...
Page 101
Er430m electronic cash register au program mode programming • 91 program 100 - plu status programming plus default to taxable by rate 1. I.E gst 1. Turn the control lock to the pgm-mode. 2. To begin the program, enter 1 0 0, press the sbtl key. 0 sbtl 0 1 3. Select the plu or plus you wish to progra...
Page 102
92 • contents er430m electronic cash register au plu status chart address program option value = sum plu is preset price? Yes = 0 no = 1 plu allows override of preset? Yes = 0 no = 2 n1 plu is taxable by rate 1(gst)? Yes = 4 no = 0 plu is taxable by rate 2? Yes = 1 no = 0 plu is taxable by rate 3? Y...
Page 103
Er430m electronic cash register au program mode programming • 93 address program option value = sum plu counter is not reset when a plu z report is done? Yes = 1 no = 0 n9 plu is preset override in mgr control? Yes = 2 no = 0 Údefault values have been highlighted in bold print.
Page 104
94 • contents er430m electronic cash register au program 110 - plu auto tare programming note: if this program has been performed, please also see program 1400 - scale tare weight programming in program mode programming - miscellaneous programming for more detail. 1. Turn the control lock to the pgm...
Page 105
Er430m electronic cash register au program mode programming • 95 program 150 - plu group assignment programming each plu may report to any three levels of 20 groups. Group totals appear on reports, so that you can track sales of different types of items. A group can also be used to designate items t...
Page 106
96 • contents er430m electronic cash register au program 200 - plu price/halo programming note: if price level in the memory allocation is set to 2, the 2 nd price level must be set as well. Price of level 2 may be $0.00. Before changing price of one of the level, original prices has to be checked. ...
Page 107
Er430m electronic cash register au program mode programming • 97 program 250 - plu stock amount programming with this program, you can add stock to the plu sales counters for plus you have designated as stock keeping plus. See “program 100 - plu status programming”. The stock number set here can be ...
Page 108
98 • contents er430m electronic cash register au program 300 - plu description programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ‘no’ in system option #25 (se...
Page 109
Er430m electronic cash register au program mode programming • 99 program 350 - plu link programming plu link programming allows you to link a plu to another plu, so that registration of the first plu will automatically trigger registration of the linked plu. For example, you may wish to link a bottl...
Page 110
100 • contents er430m electronic cash register au program 400 - plu delete programming note: to delete a plu, all totals for the plu must be cleared from z reports (including stock and plu reports.) 1. Turn the control lock to the pgm-mode. 2. To begin the program, enter 4 0 0, press the sbtl key. 0...
Page 111
Er430m electronic cash register au program mode programming • 101 program 450 - plu mix & match programming 1. Turn the control lock to the pgm-mode. 2. To begin the program, enter 4 5 0, press the sbtl key. 0 sbt l 5 4 3. Select the plu you wish to program in one of the following ways: • press a pl...
Page 112: System Option Programming
102 • contents er430m electronic cash register au system option programming refer to the “system option table” to review the system options. Read each option carefully to determine if you wish to make any changes. Default value has been highlighted in bold print. Note: because after memory all clear...
Page 113
Er430m electronic cash register au program mode programming • 103 system option table address system option value = sum 1 beeper is active? Yes = 0 no = 1 direct entry = 0 2 clerk sign on method is: code entry = 1 pop-up = yes = 1 3 clerks are: stay down = no = 0 drawer needs to be shut to operate? ...
Page 114
104 • contents er430m electronic cash register au address system option value = sum round up at 0.005 = 0 always round up = 1 12 percentage and tax calculations will: always round down = 2 round up at 0.005 = 0 always round up = 1 13 split price calculations will: always round down = 2 compulsory ea...
Page 115
Er430m electronic cash register au program mode programming • 105 address system option value = sum allow australian rounding on cash? (also see sys opt #21-3, #32-1, and #32-2) (must turn au rounding off first) yes = 1 no = 0 22 allow z stock report? Yes = 0 no = 2 enter = 1 23 training mode exit =...
Page 116
106 • contents er430m electronic cash register au note: price embedded barcode format barcode format 1 st 2 nd 3 rd 4 th 5 th 6 th 7 th 8 th 9 th 10 th 11 th 12 th 13 th type 1 d1 d2 i1 i2 i3 i4 i5 s p1 p2 p3 p4 c (5 and 4) type 2 d1 d2 i1 i2 i3 i4 s p1 p2 p3 p4 p5 c (4 and 5) type 3 d1 d2 i1 i2 i3 ...
Page 117: Print Option Programming
Er430m electronic cash register au program mode programming • 107 print option programming refer to the “print option table” to review the print options. Read each option carefully to determine if you wish to make any changes. . Default value has been highlighted in bold print. Note: because after m...
Page 118
108 • contents er430m electronic cash register au print option table address print option value = sum print media total on clerk report? Yes = 1 no = 0 1 print tax symbol? Yes = 0 no = 2 void/return totals will print on the financial report? Yes = 0 no = 1 2 audaction total will print on the financi...
Page 119
Er430m electronic cash register au program mode programming • 109 address print option value = sum print gross total on the x financial report? Yes = 0 no = 1 10 print gross total on the z financial report? Yes = 0 no = 2 print the subtotal without tax on the receipt? Yes = 1 no = 0 combine = yes = ...
Page 120
110 • contents er430m electronic cash register au address print option value = sum print preamble message on receipt? Yes = 0 no = 1 print postamble message on receipt? Yes = 0 no = 2 21 print preamble message on the guest check? Yes = 4 no = 0 print postamble message on the guest check? Yes = 1 no ...
Page 121
Er430m electronic cash register au program mode programming • 111 address print option value = sum print preamble graphic logo on the guest check? Yes = 1 no = 0 29 print postamble graphic logo on the guest check? Yes = 2 no = 0 default = yes = 0 print preamble graphic logo user = no = 1 default = y...
Page 122: Function Key Programming
112 • contents er430m electronic cash register au function key programming three programs are used to program function keys: • program 70 - function key options programming is used to set each keys individual options • program 80 - function key descriptor programming is used to program a 18 characte...
Page 123
Er430m electronic cash register au program mode programming • 113 program 70 - function key options programming use program 70 to set options for function keys. Because of the differences inherent in function keys, individual options will be different. See the specific instructions for each key in t...
Page 124
114 • contents er430m electronic cash register au program 80 - function key descriptor programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ‘no’ in system option...
Page 125
Er430m electronic cash register au program mode programming • 115 program 90 - function key halo or percentage rate programming use program 90 to program a high amount lock out (halo) for a function key. Only specific keys require this program. For example, you can set a halo for the cash, check or ...
Page 126
116 • contents er430m electronic cash register au add check (cafeteria tray total) options - program 70 add cehck cash repeat for another function key n1 sbt l 0 7 n2 n3 address option value = sum key is inactive? Yes = 1 no = 0 compulsory before tendering? Yes = 2 no = 0 n1 advance the consecutive ...
Page 127
Er430m electronic cash register au program mode programming • 117 cancel (cancel a sale) options - program 70 canc el c ash repeat for another function key n1 sbt l 0 7 address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 validat...
Page 128
118 • contents er430m electronic cash register au cash options - program 70 cash cash n1 sbt l 0 7 n2 n3 repeat for another function key address option value = sum amount tender is compulsory? Yes = 1 no = 0 allow over tendering and under tendering in x control lock position only? Yes = 2 no = 0 n1 ...
Page 129
Er430m electronic cash register au program mode programming • 119 charge (1 ~ 8) options - program 70 charge cash repeat for another function key n1 sbt l 0 7 n 2 n3 n4 n5 address option value = sum amount tender is compulsory? Yes = 1 no = 0 allow over tendering and under tendering in x control loc...
Page 130
120 • contents er430m electronic cash register au check (cheque) options - program 70 check c ash repeat for another function key n1 sbt l 0 7 n 2 n3 n4 address option value = sum amount tender is compulsory? Yes = 1 no = 0 allow over tendering and under tendering in x control lock position only? Ye...
Page 131
Er430m electronic cash register au program mode programming • 121 check (cheque) cashing options - program 70 check cash c ash n1 sbt l 0 7 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 vali...
Page 132
122 • contents er430m electronic cash register au check (cheque) endorsement options - program 70 ch eck endorse cash repeat for another function key n 1 sbtl 0 7 n2 address option value = sum key is inactive? Yes = 1 no = 0 print the amount of the check and endorsement message? Yes = 2 no = 0 n1 pr...
Page 133
Er430m electronic cash register au program mode programming • 123 check # (bill or account no.) options - program 70 check# cash repeat for another function key n1 sbt l 0 7 n2 n3 n4 address option value = sum key is inactive? Yes = 1 no = 0 required at start of sale? Yes = 2 no = 0 n1 opening clerk...
Page 134
124 • contents er430m electronic cash register au currency conversion currency conversion rate - program 90 1. Turn the control lock to the p position. 2. To begin the program, enter 9 0, press the sbtl key. 0 sbt l 9 3. Enter the exchange rate of up to 7 digits (do not enter the decimal point), and...
Page 135
Er430m electronic cash register au program mode programming • 125 drive thru / eat in / take out options - program 70 dr ive t hru cash n1 sbt l 0 7 n 2 repeat for another function key eat in cash n1 sbt l 0 7 n 2 repeat for another function key t ake out cash n1 sbt l 0 7 n 2 repeat for another fun...
Page 136
126 • contents er430m electronic cash register au error correct options - program 70 error correct cash repeat for another function key n1 sbt l 0 7 address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 validation is compulsory? Y...
Page 137
Er430m electronic cash register au program mode programming • 127 f/s tend options - program 70 f/s tend cash repeat for another function key n1 sbt l 0 7 n 2 n3 address option value = sum exempt tax 1? Yes = 1 no = 0 exempt tax 2? Yes = 2 no = 0 n1 exempt tax 3? Yes = 4 no = 0 exempt tax 4? Yes = 1...
Page 138
128 • contents er430m electronic cash register au guest options - program 70 guest c ash repeat for another function key n1 sbt l 0 7 address option value = sum required when opening a new check? Yes = 1 no = 0 before registering, enter a guest number? Yes = 2 no = 0 n1 print guest # at the kitchen ...
Page 139
Er430m electronic cash register au program mode programming • 129 macro (1 ~ 10) options - program 70 mac ro c ash repeat for another function key n1 sbt l 0 7 address option value = sum n1 key is active in x control lock position only? (eprom v2.1) yes = 1 no = 0 Údefault values have been highlight...
Page 140
130 • contents er430m electronic cash register au modifier (1 ~ 5) options - program 70 mod cash repeat for another function key n1 sbt l 0 7 n 2 n3 address option value = sum key is active in x control lock position only? Yes = 1 no = 0 n1 modify plu#? Yes = 2 no = 0 print modifier descriptor on th...
Page 141
Er430m electronic cash register au program mode programming • 131 #/ns (non add#/no sale) options - program 70 #/ns c ash repeat for another function key n1 sbt l 0 7 n 2 n3 n4 address option value = sum no sale is inactive? Yes = 1 no = 0 no sale active in x control lock position only? Yes = 2 no =...
Page 142
132 • contents er430m electronic cash register au paid out (1 ~ 3) options - program 70 p/o c ash n1 sbt l 0 7 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only yes = 2 no = 0 n1 validation is compulsory? Yes = 4 ...
Page 143
Er430m electronic cash register au program mode programming • 133 pbal options - program 70 previous balance cash n1 sbt l 0 7 repeat for another function key address option value = sum previous balance may be entered at any time? Yes = 1 no = 0 previous balance required at the start of the sale? Ye...
Page 144
134 • contents er430m electronic cash register au promo options - program 70 pr omo cash repeat for another function key n1 sbt l 0 7 n2 address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 taxable by tax 1? Yes = 4 no = 0 taxabl...
Page 145
Er430m electronic cash register au program mode programming • 135 recd on acct (1 ~ 3) options - program 70 r/a c ash n1 sbt l 0 7 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 validation is...
Page 146
136 • contents er430m electronic cash register au scale options - program 70 sc ale cash n1 sbt l 0 7 n2 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 allow manual entry of weight? Yes = 4 n...
Page 147
Er430m electronic cash register au program mode programming • 137 service (bill or account) options - program 70 ser vice cash repeat for another function key n1 sbt l 0 7 n2 n3 n4 address option value = sum compulsory non-add number before this key is used? Yes = 1 no = 0 print on receipt? Yes = 0 ...
Page 148
138 • contents er430m electronic cash register au subtotal options - program 70 subtotal cash repeat for another function key n1 sbt l 0 7 address option value = sum n1 key is inactive? Yes = 1 no = 0 Údefault values have been highlighted in bold print descriptor - program 80 - refer to “program 80 ...
Page 149
Er430m electronic cash register au program mode programming • 139 tare options - program 70 t are c ash repeat for another function key n1 sbt l 0 7 address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 using tare number five to m...
Page 150
140 • contents er430m electronic cash register au tax exempt options - program 70 tax exempt cash n1 sbt l 0 7 n2 repeat for another function key address option value = sum exempt tax 1? Yes = 1 no = 0 exempt tax 2? Yes = 2 no = 0 n1 exempt tax 3? Yes = 4 no = 0 exempt tax 4? Yes = 1 no = 0 compulso...
Page 151
Er430m electronic cash register au program mode programming • 141 tip options - program 70 t ip cash repeat for another function key n1 sbt l 0 7 n2 n3 n4 address option value = sum percentage = 1 n1 type of tip is: amount = 0 key is inactive? Yes = 1 no = 0 key is active in x control lock position ...
Page 152
142 • contents er430m electronic cash register au validate options - program 70 valid cash repeat for another function key n1 sbt l 0 7 n2 address option value = sum n1 enter port number. Enter 0 (zero) if validation is not used. (0-2) 0 key is inactive? Yes = 1 no = 0 n2 allow multiple validations?...
Page 153
Er430m electronic cash register au program mode programming • 143 waste options - program 70 wast e c ash n1 sbt l 0 7 repeat for another function key address option value = sum key is inactive? Yes = 1 no = 0 key is active in x control lock position only? Yes = 2 no = 0 n1 validation is compulsory?...
Page 154
144 • contents er430m electronic cash register au % (1 ~ 5) (discounts or surcharges) options - program 70 % cash repeat for another function key n1 sbt l 0 7 n 2 n3 n4 n6 n5 address option value = sum amount = 1 apply an: percentage = 0 key is inactive? Yes = 2 no = 0 n1 % key is active in x contro...
Page 155
Er430m electronic cash register au program mode programming • 145 descriptor - program 80 - refer to “program 80 - function key descriptor” preset % rate - program 90 % cash repeat for another function key sbt l 0 9 enter 5 digit rate or amount (see note b elow) note: if key is amount, enter 5 digit...
Page 156: Clerk Programming
146 • contents er430m electronic cash register au clerk programming clerks (which may be used as cashiers), have the following programming options. These options are set through separate programs: • program 800 - secret code programming determines the code that is used for clerk sign on if a code en...
Page 157
Er430m electronic cash register au program mode programming • 147 program 800 - secret code programming 1. Turn the control lock to the pgm-mode. 2. To begin the program, enter 8 0 0, press the sbtl key. 0 sbt l 0 8 3. Enter the number of the clerk you wish to program; press the x/time key. X/t ime ...
Page 158
148 • contents er430m electronic cash register au program 801 - drawer assignment & training clerk programming 1. Turn the control lock to the pgm-mode. 2. To begin the program, enter 8 0 1, press the sbtl key. 1 sbt l 0 8 3. Enter the number of the clerk you wish to program; press the x/time key. X...
Page 159
Er430m electronic cash register au program mode programming • 149 program 810 - clerk description programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ‘no’ in sy...
Page 160: Mix & Match Programming
150 • contents er430m electronic cash register au mix & match programming mix & match tables have the following programming options. These options are set through separate programs: • program 600 - trip level programming • program 601 - price programming • program 610 - mix & match description progr...
Page 161
Er430m electronic cash register au program mode programming • 151 program 600 - trip level programming 1. Turn the control lock to the pgm-mode. 2. To begin the program, enter 6 0 0, press the sbtl key. 0 sbt l 0 6 3. Enter the number of the m&m table you wish to program; press the x/time key. X/ti ...
Page 162
152 • contents er430m electronic cash register au program 610 - mix & match description programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ‘no’ in system optio...
Page 163: Group Programming
Er430m electronic cash register au program mode programming • 153 group programming 20 group totals are available to accumulate totals of individual plus that are assigned to each group. Each plu can be assigned to one, two or three different groups. • program 900 - group status programming allows t...
Page 164
154 • contents er430m electronic cash register au program 910 - group descriptors programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ‘no’ in system option #25 ...
Page 165: Miscellaneous Programming
Er430m electronic cash register au program mode programming • 155 miscellaneous programming program 1500 - macro key sequence programming macros are special function keys that are used to execute a sequence of key depressions. For example, a macro might be used to execute a string of reports or to a...
Page 166
156 • contents er430m electronic cash register au program 700 - logo description programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ‘no’ in system option #25 (...
Page 167
Er430m electronic cash register au program mode programming • 157 program 701 - financial report message programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ‘no...
Page 168
158 • contents er430m electronic cash register au financial report message x message line x message line x message line 1 +plu ttl 29 credit tax4 57 chg7-in-d 2 -plu ttl 30 fd/s credit 58 chg8-in-d 3 adjst ttl 31 return 59 chg1 sales 4 nontax 32 error corr 60 chg2 sales 5 gst sales 33 previous vd 61...
Page 169
Er430m electronic cash register au program mode programming • 159 program 710 - clerk report message programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ‘no’ in...
Page 170
160 • contents er430m electronic cash register au clerk report message x message line x message line x message line 1 net sale 25 credit tax3 49 chg4 sales 2 nontax 26 credit tax4 50 chg5 sales 3 gst sales 27 fd/s credit 51 chg6 sales 4 tax2 sales 28 return 52 chg7 sales 5 tax3 sales 29 error corr 5...
Page 171
Er430m electronic cash register au program mode programming • 161 program 711 - macro name programming program descriptions by typing description on the alpha keyboard overlay or by entering three digit alpha character codes. To use three digit alpha character codes you must select ‘no’ in system op...
Page 172
162 • contents er430m electronic cash register au program 1000 - nlu (number look up) code number programming nlu (number look up) are fixed keys on the keyboard (like traditional department keys) that access specific plus. On the default keyboard, there are 60 nlu keys and the plu# assigned to the ...
Page 173
Er430m electronic cash register au program mode programming • 163 program 1100 - cash-in-drawer limit programming you can set a limit for cash in drawer. When cash in drawer exceeds the limit you program here, a warning will display on the screen. You must press clear to remove the warning and conti...
Page 174
164 • contents er430m electronic cash register au program 1200 - check change limit programming use this program to set the maximum amount of cash that can be returned when a check is tendered for an amount greater than the amount of the sale. For example, if the check change limit is $10.00 the max...
Page 175
Er430m electronic cash register au program mode programming • 165 program 1300 - date and time programming use this program to set the clock and calendar on your er-430m. The date changes automatically. After initial setting, time changing will probably be required only for beginning and ending dayl...
Page 176
166 • contents er430m electronic cash register au program 1400 - scale tare weight programming a tare is the amount of weight representing the container, or package when items are sold by weight. You can pre-program five tare weights, representing the weight of different containers. When you place a...
Page 177
Er430m electronic cash register au program mode programming • 167 program 1600 - machine number programming the machine number is printed on the register receipt. Program a machine number so that any receipt can be identified with the store or register where the transaction took place. Programming t...
Page 178: Program Scans
168 • contents er430m electronic cash register au program scans since much time and energy has been invested in the planning and programming of your er-430m, it is advisable to print a hard copy of the final program for future reference. This copy should be kept in a safe place. Program 15 - program...
Page 179
Er430m electronic cash register au program mode programming • 169 others program scan refer to the chart below and enter a digit to represent the segment of the program you wish to print; press the x/time key. To see additional scan, repeat this operation. X x/t ime x program x program 0 group 9 fin...
Page 181: Sample Reports
Er430m electronic cash register au sample reports • 171 sample reports financial date 15/01/2003 wed time 13:32 x 1 report 00001 -------------------------------- financial +plu ttl 179.56 $288.60 -plu ttl 10 -20.00 adjst ttl 189.56 $268.60 -------------------------------- nontax $30.47 gst sales $15...
Page 182
172 • contents er430m electronic cash register au continued from previous page drthru ttl 1 $3.04 item disc. 3 -0.48 sale disc. 2 -5.22 sale surch. 3 $3.23 % 4 0 $0.00 % 5 0 $0.00 net sale 26 $281.18 credit gst 4 -1.11 credit tax2 1 -0.23 credit tax3 2 -0.89 credit tax4 1 -0.39 fd/s credit 0 $0.23 r...
Page 183
Er430m electronic cash register au sample reports • 173 continued from previous page r/a 3 0 $0.00 p/o 1 1 -140.00 p/o 2 0 $0.00 p/o 3 0 $0.00 hash ttl 0 $0.00 nosale 4 non add # 547 cash-in-d 14 $269.99 check-in-d 3 -108.45 fd/s-in-d 2 $21.00 chg1-in-d 0 $0.00 chg2-in-d 1 $8.43 chg3-in-d 1 $8.52 ch...
Page 184
174 • contents er430m electronic cash register au continued from previous page chg6 sales 2 $13.09 chg7 sales 0 $0.00 chg8 sales 1 $3.04 foreign 1 0.00 foreign 2 0.00 foreign 3 0.00 foreign 4 0.00 drwr ttl $216.69 promo 1 $1.50 waste 8 $12.50 tips 0 $0.00 train ttl 5 $62.59 bal forward 4 $88.13 gues...
Page 185: Time
Er430m electronic cash register au sample reports • 175 time date 15/01/2003 wed time 15:48 x 1 report 00001 -------------------------------- time 13:00-13:59 cnt 17 sales amt $183.85 sales rate 65.39% 14:00-14:59 cnt 9 sales amt $97.33 sales rate 34.61% ¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾¾ ¾ total cnt 2...
Page 186: Plu
176 • contents er430m electronic cash register au plu date 15/01/2003 wed time 15:33 x 1 report 00001 -------------------------------- all plu hamburger cnt 28 $42.00 sales rate 15.64% dbl burger cnt 40 $99.75 sales rate 37.14% coke cnt 26 $38.85 sales rate 14.46% sprite cnt 18 $13.42 sales rate 5.0...
Page 187: Clerk
Er430m electronic cash register au sample reports • 177 clerk note: media totals can be printed for each clerk, if selected in system option programming. Date 15/01/2003 wed time 15:36 x 1 report 00001 -------------------------------- all clerk ethan net sale 10 $155.23 drwr ttl $109.81 ------------...
Page 188: Individual Clerk
178 • contents er430m electronic cash register au individual clerk date 15/01/2003 wed time 15:36 x 1 report 00001 -------------------------------- individual clerk ethan net sale 10 $155.23 drwr ttl $109.81 -------------------------------- ethan 000218 00000 clerk name number of transactions net sa...
Page 189: Groups
Er430m electronic cash register au sample reports • 179 groups date 15/01/2003 wed time 15:34 x 1 report 00001 -------------------------------- group group : 1 food cnt 68 sales amt $141.75 group : 2 drink cnt 44 sales amt $52.27 group : 3 rest. Cnt 112 sales amt $194.02 group : 5 store cnt 19.16 sa...
Page 190: Stock
180 • contents er430m electronic cash register au stock date 15/01/2003 wed time 15:47 x 1 report 00001 -------------------------------- all plu stock hamburger cnt 26 dbl burger cnt 15 roast cnt 25.96 unleaded cnt 1488.47 plu33 cnt 161.25 ethan 000228 00000 plu number or plu descriptor current stoc...
Page 191: Open Check
Er430m electronic cash register au sample reports • 181 open check date 15/01/2003 wed time 15:59 x 1 report 00001 -------------------------------- open check check : 3 $24.07 table : 15 molly check : 4 $45.42 table : 8 ethan check : 5 $24.50 table : 2 ethan check : 6 $28.33 table : 6 ethan ethan 00...