Summary of SDS-901
Page 2: Edition 1, August 2011
Notice the information contained in this document is subject to change without notice. Smart-e makes no warranty of any kind with regard to this material, including but not limited to, implied warranties of merchantability and fitness for particular purpose. Smart-e will not be liable for errors con...
Page 3: Table Of Contents
Table of contents introducing smart digital solutions (sds) ......................................... What’s in the box ........................................................................................... 1 what is the sds-901? ....................................................................
Page 4: What‘S In The Box?
What‘s in the box? Thank you for buying the smart-e sds cat 5 av extender. Depending on the configuration of your system various quantities of the parts below may be included in your shipment. If any of the accessories listed below are missing please contact the smart-e dealer you purchased products...
Page 5
What is the sds-901? The sds-901 is a combination of transmitter and receiver devices, de- signed to transmit high resolution hdmi video and audio signals over cat 5 -8 wire. Av stands for audio visual and includes such signal formats as broadcast video (tv video signal—1080p, 720p & 1080i), compute...
Page 6: Installation And Operation
1. Preparing for installation start installation process by ensuring that all video displays and audio devices are compatible with the computers or multi-media sources being used. This is accomplished by connecting the devices directly to the computer and checking that the devices operate as desired...
Page 7: Installation And Operation
Installation and operation 2. Connect transmitter to the video signal source 2.1 connect the hdmi output of the source device to the input of the transmitter using a high quality hdmi cable 2.2 if needed connect the audio input to either an analogue or a toslink output of the av source. Select audio...
Page 8: Installation And Operation
Installation and operation 3. Connecting infra-red and rs232 to the transmitter 3.1 the infra-red is accessed via a 3.5mm mono jack on the left hand side of the rear panel. Using the appropriate interconnecting device (sm- led) connect the jack end to the sds-tx901 and stick the other end to the av ...
Page 9: Installation And Operation
Installation and operation - 6- 4. Led and audio function 4.1 there are 4 led indicators on the sds-901 pair i) green on rj45—shows 24v inline power ii) yellow on rj45—pulses showing correct working iii) green on front panel—show internal 5volts iv) green next to the audio connector—on for analogue,...
Page 10: Installation And Operation
5. System power up 5.1 turn the system on by plugging in the power adapter to the sds-900 transmitter (or receiver if preferred) 5.2 power up your computer. 5.3 observe both transmitter and receiver power led are on, and source device is switched on. 6. Preparing and connecting system cat-5 cable th...
Page 11
Installation and operation of receiver - 8- 7 . Connecting sds-rx901 hdmi to the display device 7.1 making sure that the cat 5 cable is connected to the transmitter output, connect the cable to the rj45 socket on the receiver unit. 7.2 if the cable connection is correct the power all 3 leds will ill...
Page 12
8. Connecting sds-rx901 to infra-red and rs232 control 8.1 if using the receiver to transmit infra-red signals back down the cable to the transmitter unit then connect an ‘eye’ (sm-eyen) to the jack position as shown in the diagram below. 8.2 if using rs232 connect control cable to the mini-jack inp...
Page 13: Mounting Of Units
9. Mounting the units 9.1 there is a 19” rack mounting kit available (rmk-191-900) which allows for up to 4 units to be assembled into a 1u shelf. Attachment is via 2 x m3 bushes in the front panel. These are fitted for both the transmitter and receiver units. 9.2 there are also holes stamped into t...
Page 14: Technical Information
Technical information sds-901 - 11- video input signal type...........................………….. Hdmi, dvi & displayport multimode formats…………………………………....... Hdmi a/deep colour 3d, 4k, 2k & 1080p signal type - connector………….. Hdmi audio input signal type…………………………………. Analogue stereo or toslink analogu...
Page 15: Appendex
Appendex - 12- limited warranty statement a. Extent of limited warranty 1. Smart-e (uk) ltd warrants to the end-user customers that smart-e product specified above will be free from defects in materials and workmanship for the duration of 1 year, which duration begins on the date of purchase by the ...
Page 16: Partial
Product range product code description smartlynx - x slx-100 transmitter and receiver pair slx-411 transmitter and receiver pair smartlynx-x + slx-111 100m transmitter and receiver pair with rs232/ir slx-214 300m transmitter and receiver pair with rs232/ir slx-100 300m transmitter and receiver pair ...