Surveon CAM6100 Operating Instructions Manual - Preparations For The Pc
12
PREPARATIONS FOR THE PC
To set up the network of the camera via PC,
you have to change the TCP/IP settings of the
PC.
The following are the default network settings
of the camera.
IP address :192.168. 1. 2
Subnet mask :255.255.255.0
To access the amera, the IP address of the
PC should match the address below.
(NOTE: xxx should be a number from 3 to
254)
IP address :192.168. 1.xxx
Subnet mask :255.255.255. 0
NOTE: The procedure below is the setup
procedure of a PC using Windows XP as its
OS. When running an OS other than Windows
XP, please refer to the manual included with
the OS.
Start up your PC.
Click the [Start] and select "Control Panel"
■ PC Network Setup
-17-
PREPARATIONS FOR THE PC
■
Network Setup of Your PC
To set up the network of the PC, first change the TCP/IP
settings of the PC to match them to the default settings
of the camera.
The following are the default network settings of the
camera.
IP address
: 192.168.0.10
Subnet mask
: 255.255.255.0
Default gateway
: 192.168.0.1
To access the camera, the IP address of the PC should
be "192.168.0.XXX" (where XXX should be a number
from 2 to 254 except 10).
Note: The procedure described below is based on the
assumption that Windows XP is running on the PC.
When running an OS other than Windows XP, see
the manual included with the OS.
1. Start up your PC.
2. Click the [Start] button and select "Control Panel".
3. Double-click
the
"Network
and
Internet
Connections" icon.
4. Double-click the "Network Connections" icon.
5. Click "Local Area Connection 2", and then click
"Change settings of this connection" in the "Network
Tasks" menu.
6. Click "Internet Protocol (TCP/IP)", and then click the
[Properties] button.
➜
➜
➜
➜
➜
-17-
PREPARATIONS FOR THE PC
■
Network Setup of Your PC
To set up the network of the PC, first change the TCP/IP
settings of the PC to match them to the default settings
of the camera.
The following are the default network settings of the
camera.
IP address
: 192.168.0.10
Subnet mask
: 255.255.255.0
Default gateway
: 192.168.0.1
To access the camera, the IP address of the PC should
be "192.168.0.XXX" (where XXX should be a number
from 2 to 254 except 10).
Note: The procedure described below is based on the
assumption that Windows XP is running on the PC.
When running an OS other than Windows XP, see
the manual included with the OS.
1. Start up your PC.
2. Click the [Start] button and select "Control Panel".
3. Double-click
the
"Network
and
Internet
Connections" icon.
4. Double-click the "Network Connections" icon.
5. Click "Local Area Connection 2", and then click
"Change settings of this connection" in the "Network
Tasks" menu.
6. Click "Internet Protocol (TCP/IP)", and then click the
[Properties] button.
➜
➜
➜
➜
➜
-17-
PREPARATIONS FOR THE PC
■
Network Setup of Your PC
To set up the network of the PC, first change the TCP/IP
settings of the PC to match them to the default settings
of the camera.
The following are the default network settings of the
camera.
IP address
: 192.168.0.10
Subnet mask
: 255.255.255.0
Default gateway
: 192.168.0.1
To access the camera, the IP address of the PC should
be "192.168.0.XXX" (where XXX should be a number
from 2 to 254 except 10).
Note: The procedure described below is based on the
assumption that Windows XP is running on the PC.
When running an OS other than Windows XP, see
the manual included with the OS.
1. Start up your PC.
2. Click the [Start] button and select "Control Panel".
3. Double-click
the
"Network
and
Internet
Connections" icon.
4. Double-click the "Network Connections" icon.
5. Click "Local Area Connection 2", and then click
"Change settings of this connection" in the "Network
Tasks" menu.
6. Click "Internet Protocol (TCP/IP)", and then click the
[Properties] button.
➜
➜
➜
➜
➜
-17-
PREPARATIONS FOR THE PC
■
Network Setup of Your PC
To set up the network of the PC, first change the TCP/IP
settings of the PC to match them to the default settings
of the camera.
The following are the default network settings of the
camera.
IP address
: 192.168.0.10
Subnet mask
: 255.255.255.0
Default gateway
: 192.168.0.1
To access the camera, the IP address of the PC should
be "192.168.0.XXX" (where XXX should be a number
from 2 to 254 except 10).
Note: The procedure described below is based on the
assumption that Windows XP is running on the PC.
When running an OS other than Windows XP, see
the manual included with the OS.
1. Start up your PC.
2. Click the [Start] button and select "Control Panel".
3. Double-click
the
"Network
and
Internet
Connections" icon.
4. Double-click the "Network Connections" icon.
5. Click "Local Area Connection 2", and then click
"Change settings of this connection" in the "Network
Tasks" menu.
6. Click "Internet Protocol (TCP/IP)", and then click the
[Properties] button.
➜
➜
➜
➜
➜
Double-click the "Network and Internet
connections" icon
Double-click the "Network Connctions" Icon
Click "Local Area Connection 2 ", and then
click "Change settings of this connections" in
the "Network Task" menu