Surveon Linux Series Quick Installation Manual
QUICK INSTALLATION GUIDE
Installation
© by Surveon Technology, Inc. All rights reserved.
Password
:
Only
qualified service personnel should install and service this product in order to avoid risk of injury from
electrical
shock and energy hazard.
Observe
all ESD (Electro-static Discharge) procedures during installation to avoid damage to the recorder
and
its components.
Warning!
Q MS MR L I 0 0 1 1 2
Adding
Hard Drives
2
Hard
Drive Installation Prerequisites
Purchase hard drives having the same capacity and using same interface with the pre-installed ones.
Hard disk drives (HDD) are purchased separately. When selecting HDDs, HDD manufacturers always urge
users to choose enterprise/surveillance grade drives for 24/7 surveillance operations to ensure system stability.
The surveillance hard drives on our Approved Vendor List (AVL) are engineered to work continuously, withstand
high-temperature fluctuations and equipment vibrations found in any typical surveillance application.
To reduce errors occurred on your RAID data and the chance of the recording performance being affected,
it is highly recommended to use HDDs listed on our Approved Vendor List (AVL) to ensure reliability.
Find the AVL on our web page:
http://www.surveon.com/support/hardware.asp
Inserting
Hard Drive into Drive Tray
1. Open the front panel of the EMR system.
2. Press the release button (indicated by the blue arrow)
on the bezel, the bezel panel should open automatically
and gently pull out the hard drive tray.
3. Place the hard drive into the drive tray.
Make sure the hard drive’s interface
connector is the open side of the drive
tray and its label side facing up. Adjust
the drive’s location until the mounting
holes in the drive tray are aligned with
those on the hard drive. Secure the drive
with four supplied flat head screws
.
Smart Megapixel Recorder
Series
Linux
4. With the tray bezel open, insert the hard drive and
tray into the system enclosure.
5. Close the tray bezel.
6. Use the small flat blade screw driver to turn the bezel lock
from the unlock to lock position.
7. Repeat above steps to install other hard drives.
8. Close the system front panel when you are done installing
hard drives.
/4
1/3
User-provide Items
●
Quick
Installation Guide x1
●
Product
DVD x1 (including manuals)
●
Power
Cord x1
Power Adapter x1
●
●
HDD
Screw x20
Accessories for 2 Bay Models
●
Quick
Installation Guide x1
●
Product
DVD x1 (including manuals)
●
Power
Cord x2 (for Europe)
x1 (for other zones)
●
Power
Cord
●
HDD
Screw x40
Accessories for 8 Bay Model
Front
View
Hardware Overview
1
1
LCD
Display
2
Enter
Switch
3
Select
Switch
LED
Indicators
Power Switch
4
5
6
Front
USB Connector
9
Model
2 bay models
5 bay model
Space for Hard Drives
RAID Options
2 HDD
5 HDD
NonRAID, RAID1
NonRAID, RAID1,5, 6
System Connections
3
●
●
Insert the LAN Cable to the LAN Port to a local network where your IP Camera reside.
(Connection to analog cameras is also available via an IP encoder).
●
Connect an external monitor capable of 32 bit or higher color quality to the VGA port to view the
VMS interface.
Insert mouse, keyboard to the USB for operating VMS on the SMR system.
Connect cables to the rear panel ports as follows:
Check Network Topology
Please make sure if your network environment has DHCP service. For devices without DHCP server
function such as switch and hub, please choose Fixed IP Address in Install Wizard.
and then enable DHCP server after logging into VMS.
Remote Client/Web Client
Management Center
VGA Station for Local Client
Internet
SELECT
ENTER
S M R Pro
DHCP Router
GbE Switch
Smart Megapixel Video Recorder
Camera(s)
Rear
View
Power
Socket
e
-SATA Port x1
USB
Port x4
HDMI
Port
LAN
Port x2
Restore
Button
USB
Port x2
Safety
Switch
Audio
Ports
VGA
Port
Kensington
Lock-hole
COM
Port
12V
DC Power Port
5
6
7
8
9
10
11
12
7
2
3
4
5
6
8
1
2
3
4
5
6
7
8
13
Note:
The functions of e-SATA port and COM port are reserved.
Powering
up
4
2 Bay Models
1. Attach the power cable to the power socket on the rear panel.
2.
3. See if the system LED is blinking, which means that the system
is starting up.
4. See if the network LED has turned green, which indicates that
the power is on and network is connected.
5. See if the HDD LED is on, which means that the hard drive can
be accessed.
Press the power switch.
LED
Indicators
Power
Switch
LED
Indicators
LCD
Display
Power
Switch
1. Attach the power cable to the power socket on the rear panel.
2. Make sure the safety switch on the rear panel is switched to the “-”
side, which means that it is turned on.
3.
4. See if the system LED is blinking, which means that the system
is starting up.
5. See if the network LED has turned green, which indicates that
the power is on and network is connected.
6. See if the HDD LED is on, which means that the hard drive can
be accessed.
7. The Server name and the IP address will be shown on the LCD screen.
Press the power switch.
5 / 8 Bay Models
13
11
4
9
6
11
7
8 bay model
8 HDD
NonRAID, RAID1,5, 6
5
4
11
13
4
9
6
11
7
5
4
1 2
3
SMR Pro
SMR Pro
●
Quick
Installation Guide x1
●
Product
DVD x1 (including manuals)
●
Power
Cord x1
Power Adapter x1
●
●
HDD
Screw x40
Accessories for 5 Bay Model
●
Flat blade screwdriver & Philips screwdriver
●
●
Monitor
LAN Cable
USB compatible Keyboard and Mouse
●
●
3.5" SATA Hard Drive
●
(Optional) PC(s) with Windows XP (or above) Used as Remote
VMS Client Management Center
SMR2100
SMR2110
SMR5110
SMR2100
SMR5110
SMR8300
SMR2110
8
8
1
2 3
4
5
6
SMR8300