Summary of DPM-1122
Page 1
Owner‘s manual power mixer with 24-bit digital effects dpm-1122.
Page 2
2 contents important safety instructions! ..........................................................................................................................3 cleaning and care .......................................................................................................................
Page 3
3 important safety instructions! For your own safety you must read through this chapter at first completely! Risk of electrical shocks. Only connect the device to a properly wired and earthed mains power socket providing mains voltage of • 230 v ~ /50 hz. Do not operate the device if the power cord ...
Page 4
4 introduction thank you for your purchasing of the t.Mix dpm 1122 16-channel power mixer with 24-bit digital multi-effect built-in. Your the t.Mix dpm 1122 is a remarkable compact powered mixer that doesn’t find many equals in the market today. With 12 microphone and 2 stereo line-level inputs for ...
Page 5
5 becoming acquainted with the operational surface.
Page 6
6 small gig hookup diagram (the displayed amplifier is optional - of course you can connect the speakers to the speaker sockets on the rear panel of the mixer.) computer set-up diagram.
Page 7
7 the control elements . . . . . . On the front panel 1. Themonomic/linechannels your the t.Mix dpm 1122 is equipped with 12 low-noise microphone preamplifiers with optional phantom power, 50 db of gain and over 100db of s/n ratio. You can connect almost any type of microphone. Dynamic microphones d...
Page 8
8 7. Hi if you turn this control up, you will boost all the frequencies above 12 khz (shelving filter). You will add transparency to vocals and guitar and also make cymbals crispier. Turn the control down to cut all frequencies above 12 khz. In such way you can reduce sibilance of human voice or red...
Page 9
9 17. Peakled inside your dpm 1122 the audio signal is monitored in several different stages and then sent to the peak led. When the led is red illuminated, it warns you that you are reaching signal saturation and possible distortion. Then you should reduce the input level for avoiding distortion. 1...
Page 10
10 27. Fx1/2tomainlevelcontrol this fader is used to adjust the level of the processed signal which is sent from the dsp to main mix bus. 28. Aux1-4controls these knobs are used to adjust the amount of the signal sent from the aux sends1-4 jacks to the aux1, 2 ,3 and 4 buses. 29. 2-trackinlevelcontr...
Page 11
11 39. Comp./bypassswitch&led push this switch, the led will light up and you will activate the main mix compressor. You can also use the bypass switch to make a comparison between processed and unprocessed signal. 40. Auxsendsconnectors these 1/4” phone jacks are used to send out the signal from th...
Page 12
12 . . . On the rear panel 50. Acinletwithfuseholder use it to connect your dpm 1122 to the main ac with the supplied ac cord. Please check the voltage available in your country and how the voltage for your unit is configured before attempting to connect your unit to the main ac. 51. Poweron/offswit...
Page 13
13 audio connections you can connect unbalanced equipment to balanced inputs and outputs. Simply follow these schematics:.
Page 14
14 and now some tips how to use the amplifier mode switch this is the most common application. The built-in amplifier drives two main speaker cabinets left and right. The amplifier mode is on main l+main r position. With the amplifier mode in aux1+aux2 position, the built-in amplifier drives two mon...
Page 15
15 preset list.
Page 16
16 block diagram.
Page 17
17 technical specifications.
Page 18
18 disposal neverthrowthedeviceintotheregularhouseholdwasteattheendofitsusefullife. Thisproductissubjecttotheeuropeandirective2002/96/ec. Dispose of the device through an approved disposal centre or at your community waste facility. • observe the current existing regulations. In case of doubt contac...
Page 19
19.
Page 20
? 2010 musikhaus thomann treppendorf 30 • 96138 burgebrach • germany www.Thomann.De.