T.MIX pm184x Owner's Manual - page 5
B:MASTER SECTION
(1) FX PROCESSOR DIRECT IN
The external signals can be connected with the DSP input
(2) AUX SEND
Aux signal output jack
(3) FX SEND
FX signal output jack
(4) AUX RETURN
FX output signal return jack
(5) FX RETURN
FX output signal return jack
(6) DIGITAL EFFECTS PROCESSOR
24-bit stereo 32-effect processor with ultra-high resolution 46KHz, 20-bit AD/DA converters, for internal and external use.
(7) SEVEN-BAND GRAPHIC EQ
It can adjust input sensity from-10dB to +10dB at the following frequencies: 60Hz, 160Hz, 410Hz, 1.1KHz, 2.3KHz, 6.2KHz and 15.6KHz.
(8) EQ IN
When pushing the switch, it can release the output signal from EQ. The switch is off, then the signal is not from EQ.
(9) AUX SENDS GAIN CONTROL
You can have a further +15dB available from these outputs
(10) FX SENDS GAIN CONTROL
You can have a further +15dB available from them
(11) AUX PFL
(12) FX PFL
(13) AUX OUTPUT CONTROL
Adjusting the fader, you can get different output level from AUX
(14) FX OUTPUT CONTROL,
You can adjust the output level of aux.
(15) ALT3-4 OUTPUT LEVEL CONTROL
You can control the ALT3-4 signals separately.
(16)(17) L. R MASTER OUTPUT CONTROL
You can control the L. R signal by adjusting the two fades.
(18) 2-TRACK INPUT
It is primarily for auditioning mix playback from tape.
(19) ALT3-4 OUTPUT PFL
(20) ALT3-4 BUS
(21) HEADPHONE VOLUME CONTROL
Using the control, you can control the output level of headphone and monitor the signals reverb from speaker.
(22) 2-TRACK OUTPUT
(23) MAIN MIX
7
PM SERIES PROFESSIONAL MIXING CONSOLE
4
All channels of powered mixers & mixing consoles are the same. Therefore ,this manualhows the control functions of only one
channel.
(1)MICROPHONE
Electronically Microphone inputs accept a standard XLR male connector.
1.GROUND=shield, 2.HOT=signal input, 3.COLD=ground(shield).
You can use max 10-60dB according to signallevel by GAIN control.
(2)LINE INPUT
USING BY 1/4"standard line connector,You can use unbalance(tip/signal) and balance(tip/ring/signal). It can be connected with
keyboards orother electric instruments.
Tip=positive ring=negative sleeve=ground.
(3)LOW CUT
This switch, when push, cut the input signal below 75Hz.
(4)GAIN CONTROL
Adjust input sensitivity from 10dB to 60dB with the 60dB pad switch in the out position and -40dB to +10dB when the 60dB pad
switch is pushed.
A.CHANNEL SECTON
CHARACTORS
6 mono input channels with gold plated XLRs, balanced line inputs and inserts.
ultra-low noise discrete mic preamps with +48V phantom power.
4 stereo input channels with balanced jacks.
2 additional multi-functional stereo channels with 60mm faders.
switchable 7-band graphic equalizer for ultimate main mix equalization.
ALT 3-4 bus routable to main mix and control room with insert, PFL and 60mm masterfader.
extremely high headroom-offering more dynamic range.
balanced inputs and main outputs for highest signal integrity.
ultra-musical 4-band EQ (stereo channels) and 3-band EQ with sweepable mid band (mono channels).
peak LEDS and switchable low-cut filter on all mono channels.
2 AUX sends (AUX 1 pre/post)per channel, for internal or external effects and monitoring.
master AUX sends with gain control and PFL.
mute/ALT 3-4, solo-in-place and pre-fader-listen function on all channels.
separate main mix, ALT 3-4, control room and headphone outputs.
2-track inputs assignable to main mix or control room/headphone outputs.
highly accurate 12-segment bargraph meters.
high quality 60mm panasonic faders and sealed potentiometers.
PM SERIES PROFESSIONAL MIXING CONSOLE