- DL manuals
- Tait
- Two-Way Radio
- TM9100
- Installation Manual
Tait TM9100 Installation Manual
Summary of TM9100
Page 1
Tm9100 110w mobile radios installation guide mma-00039-03 · issue 3 · october 2012.
Page 2
2 tm9100 110w mobile radio installation guide © tait limitedoctober 2012 contact information tait communications corporate head office tait limited p.O. Box 1645 christchurch new zealand for the address and telephone number of regional offices, refer to our website: www.Taitradio.Com copyright and t...
Page 3: Contents
Tm9100 110w mobile radio installation guide 3 © tait limitedoctober 2012 contents preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 scope of manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 4: Preface
4 preface tm9100 110w mobile radio installation guide © tait limitedoctober 2012 preface scope of manual this manual describes how to install a tm9100 110w mobile radio, including microphone, antenna, emergency switch, and external alert device. The installation of accessories is described in the in...
Page 5: Document Conventions
Tm9100 110w mobile radio installation guide preface 5 © tait limitedoctober 2012 document conventions please follow exactly any instruction that appears in the text as an ‘alert’. An alert provides necessary safety information as well as instruction in the proper use of the product. This manual uses...
Page 6: Safety Warnings
6 safety warnings tm9100 110w mobile radio installation guide © tait limitedoctober 2012 safety warnings this section contains important information on the safe installation of the radio. You must read this information before starting the installation. You must also read and observe the safety infor...
Page 7: Negative Earth Supply
Tm9100 110w mobile radio installation guide safety warnings 7 © tait limitedoctober 2012 interference with vehicular electronics warning some vehicular electronic devices may be prone to malfunction due to the lack of protection from rf energy when your radio is transmitting. Examples of vehicular e...
Page 8
8 safety warnings tm9100 110w mobile radio installation guide © tait limitedoctober 2012.
Page 9: Introduction
Tm9100 110w mobile radio installation guide introduction 9 © tait limitedoctober 2012 1 introduction the tm9100 110w mobile radio is a p25-compliant radio in the vhf (136-174mhz) frequency range with 110w transmit power output. It consists of a standard tm9100 mobile enclosed in a strong chassis on ...
Page 10: Preparing The Installation
10 preparing the installation tm9100 110w mobile radio installation guide © tait limitedoctober 2012 2 preparing the installation this section contains the following information to assist you in preparing for the actual installation: ■ regulations ■ installation tools ■ checking the equipment for co...
Page 11: 2.4
Tm9100 110w mobile radio installation guide preparing the installation 11 © tait limitedoctober 2012 2.4 programming settings make sure that the radio has been correctly programmed before installing it. The radio can only be programmed via the control head microphone socket, not via the sockets on t...
Page 12: Installing The Radio
12 installing the radio tm9100 110w mobile radio installation guide © tait limitedoctober 2012 3 installing the radio this section explains how to install and check the radio and its associated equipment. It contains the following information: ■ selecting the mounting position ■ installing the anten...
Page 13: 3.2
Tm9100 110w mobile radio installation guide installing the radio 13 © tait limitedoctober 2012 3.2 installing the antenna this section provides information on installing an external antenna within the rf exposure limits. Install the external antenna (not supplied) according to the antenna manufactur...
Page 14: 3.3
14 installing the radio tm9100 110w mobile radio installation guide © tait limitedoctober 2012 3.3 connecting the power cable to the power source power is supplied to the 110w mobile via a cable with a db15 connector (provided). This plugs into the external rf amplifier, which provides power to the ...
Page 15: 3.4
Tm9100 110w mobile radio installation guide installing the radio 15 © tait limitedoctober 2012 2. Run the supplied power cable (or one with a higher current rating) between the radio’s mounting position and the vehicle battery (12v) and cut it to length, allowing approximately 8 inches (20 cm) exces...
Page 16: 3.5
16 installing the radio tm9100 110w mobile radio installation guide © tait limitedoctober 2012 3.5 installing the microphone this section describes the radio’s microphone connector and the information required to connect the microphone and install the microphone clip. Notice the microphone grommet m...
Page 17: 3.6
Tm9100 110w mobile radio installation guide installing the radio 17 © tait limitedoctober 2012 3.6 connecting to the ignition signal ignition sense allows the radio to be turned on and off with the ignition key of the vehicle. The tm9100 110w mobile radio is already fitted with an ignition sense kit...
Page 18: 3.7
18 installing the radio tm9100 110w mobile radio installation guide © tait limitedoctober 2012 3.7 connecting a remote speaker if a high-power remote speaker is required, tait recommends using the tmaa10-03 high-power remote speaker for 25w radios. Installation instructions (ipn 402-00010-xx) are pr...
Page 19: 3.8
Tm9100 110w mobile radio installation guide installing the radio 19 © tait limitedoctober 2012 3.8 connecting to an emergency switch and/or external alert devices the auxiliary connector can be used to connect external devices and signals that are typically connected to a radio. These devices and si...
Page 20
20 installing the radio tm9100 110w mobile radio installation guide © tait limitedoctober 2012 external alert device the radio allows for output to external alert devices using the digital gpio lines of the auxiliary connector and the internal options connector. Aux gpio4 can be fitted with a power ...
Page 21: 3.9
Tm9100 110w mobile radio installation guide installing the radio 21 © tait limitedoctober 2012 3.9 mounting the radio once the cables are all in position, you attach them to the radio and secure it in its mounting location. The procedure varies, depending on whether you are using the base plate and ...
Page 22: 3.10
22 installing the radio tm9100 110w mobile radio installation guide © tait limitedoctober 2012 3.10 checking the installation warning danger of fire. The radio’s protection mechanisms rely on the correct fuses on both the negative and positive power supply leads being present. Failure to fit the cor...
Page 23
Tm9100 110w mobile radio installation guide 23 © tait limited october 2012 tait software license agreement this software license agreement ("agreement") is between you (“licensee”) and tait limited (“tait"). By using any of the software items embedded and pre-loaded in the related tait designated pr...
Page 24
24 tm9100 110w mobile radio installation guide © tait limitedoctober 2012 ment contains or is derived from open source software, the terms and conditions governing the use of such open source software are in the open source software licenses of the copyright owner and not in this agreement. If there...
Page 25
Tm9100 110w mobile radio installation guide 25 © tait limited october 2012 program or documentation errors or security vulnerabilities. If tait cannot correct the defect within a reasonable time, then at tait option, tait will replace the defective software with function- ally equivalent software, l...
Page 26
26 tm9100 110w mobile radio installation guide © tait limitedoctober 2012 construed as an admission or presumption of pub- lication of the software or public disclosure of any trade secrets associated with the software. 11.2. Compliance with laws. Licensee acknowledges that the software may be subje...