Takex PB-100TK Instruction Manual - page 4
Symptom
Possible Cause
Remedy
Operation LED
1. No power supply.
1. Turn on the power.
does not light
2. Bad wiring connection or broken wire, short.
2. Check wiring.
Alarm LED does
1. No power supply.
1. Turn on the power supply.
not light when the
2. Bad wiring connection or broken wire, short.
2. Check wiring.
beam is broken
3. Beam is reflected on another object and sent into the receiver.
3. Remove the reflecting object or change beam direction.
4. Two beams are not broken simultaneously.
4. Break two beams simultaneously.
5. The beam interruption time is shorter than the set response time.
5. Set the response time shorter.
Alarm LED continues 1. Beam alignment is out.
1. Check and adjust again.
to light.
2. Shading object between Transmitter and Receiver.
2. Remove the shading object.
3. Optics of units are soiled.
3. Clean the optics with a soft cloth.
Intermittent alarms
1. Bad wiring connection.
1. Check again.
2. Change of supply voltage.
2. Stabilize supply voltage.
3. Shading object between Transmitter and Receiver.
3. Remove the shading object.
4. A large electric noise source, such as power machine, is located
4. Change the place for installation.
nearby Transmitter and Receiver.
5. Unstable installation of Transmitter and Receiver.
5. Stabilize.
6. Soiled optics of Transmitter and Receiver.
6. Clean the optics with a soft cloth.
7. Improper alignment.
7. Check and adjust again.
8. Small animals may pass through the 2 beams.
8. Set the response time longer. (Impossible in a site
where an intruder can run at full speed.)
Model
PB-30TK
PB-60TK
PB-100TK
Detection system
Simultaneous breaking of 2 beams
Infrared beam
LED pulsed beam, Double modulation
Protection distance
Outdoor 100’ (30m) or less
Outdoor 200’ (60m) or less
Outdoor 330’ (100m) or less
Indoor 200’(60m) or less
Indoor 400’(120m) or less
Indoor 660’(200m) or less
Max.beam range
Outdoor 1000’ (300m) or less
Outdoor 2000’ (600m) or less Outdoor 3300’ (1000m) or less
(Approximation)
Indoor 1000’(300m) or less
Indoor 2000’(600m) or less
Indoor 3300’(1000m) or less
Response time
50msec.to 700msec. (Variable at pot)
Supply voltage
10V to 30VDC (Non-polarity)
Current
53mA or less
80mA or less
consumption
Dry contact relay output form C
Contact action: Interruption time + delay time
Alarm output
(1 to 3 sec.)
Contact capacity: 30V AC/DC, 0.5A or less
Dry contact relay N/C
Tamper output
Action :
Activated when cover is detached.
Contact capacity: 30V AC/DC, 0.5A or less
Alarm LED
Red LED (Receiver)
ON: when an alarm is initiated
Attenuation LED
Red LED (Receiver)
ON: when beam is attenuated
Functions
Monitor jack output AGC circuit, Frost proof cover
Ambient temperature
-13ºF to +140ºF (-25ºC to +60ºC)
range
Mounting positions
Indoor / Outdoor
Wiring
Terminals
Weight
Transmitter: 13.3oz (380g) Receiver:14oz (400g)
Appearance
PC resin (wine red)
Limited Warranty
All TAKEX Products are subject to 5 years warranty.
All other warranty periods agreed are subject to a formal written agreement.
During the warranty period, TAKEX Europe Ltd. will repair or replace, as its sole
option, free of charge, any defective parts returned prepaid.
Our warranty does not cover damage or failure caused by Acts of God, abuse, misuse,
abnormal usage, faulty installation, improper maintenance, unauthorised customer
modifications or any repairs other than those carried out by TAKEX Europe Ltd.
TAKEX EUROPE LTD.
Aviary Court, Wade Road,
Basingstoke,
HANTS RG24 8PE
UK
Tel. +44(0)1256-475555
Fax. +44(0)1256-466268
Email: sales@takexeurope.com
Webpage: www.takexeurope.com
Knockout
Knockout
Grommet
PB-100TK IM-10/04 (CRI-174)
The specifications are subject to change without notice.