Talon Tools FH2700 User Manual

Summary of FH2700

  • Page 1

    7096-270003 warning • please read for your own safety please read this manual before attempting to operate your new unit. Failure to follow instructions can result in serious personal injury. Spend a few moments to familiarize yourself with your petrol high pressure cleaner before each use. Petrol h...

  • Page 2

    This manual covers the operation and maintenance of talon high pressure cleaner. Please read and understand this manual before using your new high pressure cleaner. If assistance is required, please contact talon tools australia or any talon tools authorised servicing dealer. To emphasise special in...

  • Page 3

    4 talon high pressure cleaners are designed to give safe and dependable service if operated according to instructions. Read and understand this user manual before operating your high pressure cleaner. You can help prevent accidents by being familiar with your machines controls, and by observing safe...

  • Page 4

    6 7 danger - risk of unsafe operation 1. Do not use chlorine bleach or any other corrosive compound. 2. Become familiar with the operation and controls of the pressure washer. 3. Keep operating area clear of all persons, pets, and obstacles. 4. Do not operate the product when fatigued or under the i...

  • Page 5

    9 8 know your petrol high pressure cleaner general identification au 1 2 4 11 3 5 6 7 8 9 24 22 21 20 13 19 10 16 18 17 23 1. High pressure gun 2. High pressure hose 3. Air filter 4. Throttle lever 5. Choke lever 6. Fuel lever 7. Spray wand 8. Quick connect fitting 9. 8î wheels 10. Starter handle 11...

  • Page 6

    10 3-4. Connect hose and water supply to pump-fh2700 important you must assemble the nozzle extension and attach all hoses before you start the engine. Starting engine without all hoses connected and water supplied will damage the pump. 1. Connect high pressure hose to pump outlet. (fig. 3-4a). 2. C...

  • Page 7

    Caution there must be at least ten feet of unrestricted garden hose between the pressure washer inlet and any flow shut-off device, such as a 'y' shut-off connector or other convenience-type water shut-off valves. Damage to pressure washer resulting from disregarding this caution will not be covered...

  • Page 8

    Off on open close f ast slow 1. Move the fuel valve (a) to the on position. (fig. 4-1a) 2. Move choke lever (b) to close position for cold engine starting. Turn choke lever (b) to open position for warm engine starting.(fig. 4-1b) 3. Move the throttle lever (c) fully to the left (fast).(fig. 4-1c) 4...

  • Page 9

    Warning • petrol is explosive under certain conditions. • refuel in a well-ventilated area with the engine stopped. Do not smoke or allow flames or sparks in the area where the engine is refueled or where gasoline is stored. • do not overfill the fuel tank (there should be no fuel in the filler neck...

  • Page 10

    18 operation au 6.3 maintenance schedule note (1) service more frequently when used in dusty areas. (2) these items should be serviced by an authorized talon dealer. 6.4 basic elements of a pressure washer • high pressure pump: increases the pressure of the water supply. • engine: drives the high pr...

  • Page 11

    20 21 operation au oil filler cap / dipstick drain plug 6.8 spark plug service to ensure proper engine operation, the spark plug must be properly gapped and free of deposits. 1. Remove the spark plug if the engine has been running, the muffler will be very hot. Be careful not to touch the muffler (a...

  • Page 12

    22 23 spray lance au 7.1 changing nozzles on spray wand caution the high pressure spray from your pressure washer is capable of causing damage to surfaces such as wood, glass, automobile paint, auto striping and trim, and delicate objects such as flowers and shrubs. Before spraying, check the item t...

  • Page 13

    24 troubleshooting au 9. Troubleshooting the pressure washer problem probable cause corrective action pump has following problems: failure to produce pressure, erratic pressure, chattering, loss of pressure, low water volume. 1. Low pressure nozzle installed. 2. Water inlet is blocked. 3. Inadequate...