1. DL manuals
  2. TANDBERG
  3. Receiver
  4. TT1260
  5. Reference Manual

TANDBERG TT1260 Reference Manual

Other manuals for TT1260: Instruction Manual, Reference Manual
Manual is about: Contribution Receiver

Summary of TT1260

  • Page 1

    St.Re.E10100.3 issue 3 english (uk) reference guide tt1260 contribution receiver software version 5.2.1 (and later) tt1260/dirbas, tt1260/cibas[/48] and options tt1260 contribution receiver.

  • Page 2

    Preliminary pages page ii reference guide: tt1260 contribution receiver st.Re.E10100.3 issue 3 first published in 2007 by: t andberg t elevision l td r egistered a ddress : u nit 2 s trategic p ark , c omines w ay , h edge e nd , s outhampton , h ampshire , so30 4da u nited k ingdom registered compa...

  • Page 3: List of Contents

    Preliminary pages reference guide: tt1260 contribution receiver page iii st.Re.E10100.3 list of contents chapter 1: introduction this chapter identifies the equipment versions covered by this manual; describes the purpose of the equipment in a typical system; provides a summary of its main features;...

  • Page 4: About This Reference Guide

    Preliminary pages page iv reference guide: tt1260 contribution receiver st.Re.E10100.3 about this reference guide this reference guide provides instructions and information for the installation, operation of the tt1260 contribution receiver. This reference guide should be kept in a safe place for re...

  • Page 5: Warnings, Cautions and Notes

    Preliminary pages reference guide: tt1260 contribution receiver page v st.Re.E10100.3 warnings, cautions and notes heed warnings all warnings on the product and in the operating instructions should be adhered to. The manufacturer can not be held responsible for injuries or damage where warnings and ...

  • Page 6: Contact Information

    Preliminary pages page vi reference guide: tt1260 contribution receiver st.Re.E10100.3 contact information tandberg television customer services support services our primary objective is to provide first class customer care that is tailored to your specific business and operational requirements. All...

  • Page 7: Technical Training

    Preliminary pages reference guide: tt1260 contribution receiver page vii st.Re.E10100.3 technical training training courses tandberg television provides a wide range of training courses on the operation and maintenance of our products and on their supporting technologies. Tandberg can provide both r...

  • Page 8: Technical Publications

    Preliminary pages page viii reference guide: tt1260 contribution receiver st.Re.E10100.3 technical publications if you need to contact tandberg television technical publications regarding this publication, e-mail: techpubs@tandbergtv.Com..

  • Page 9: Contents

    Reference guide: tt1260 contribution receiver page 1-1 st.Re.E10100.3 chapter 1 1. Introduction contents 1.1 scope of this reference guide ........................ 1-3 1.1.1 who should use this reference guide ..................................................... 1-3 1.1.2 what equipment is covered ...

  • Page 10

    Introduction page 1-2 reference guide: tt1260 contribution receiver st.Re.E10100.3 list of figures figure 1.1: front view of the tt1260 ................................... 1-3 figure 1.2: typical satellite compression system................ 1-9 figure 1.3: what the satellite receiver does .............

  • Page 11: 1.1

    Introduction reference guide: tt1260 contribution receiver page 1-3 st.Re.E10100.3 1.1 scope of this reference guide 1.1.1 who should use this reference guide this reference guide is written for operators/users of variants of the tt1260 contribution receiver and options. It describes the unit’s func...

  • Page 12: 1.2

    Introduction page 1-4 reference guide: tt1260 contribution receiver st.Re.E10100.3 1.2 summary of features 1.2.1 main features the tt1260 is fully compliant with the appropriate sections of the mpeg-2 1 , dvb-s 2 and dsng 3 specifications and offers the following features: • front panel controls and...

  • Page 13

    Introduction reference guide: tt1260 contribution receiver page 1-5 st.Re.E10100.3 support for pal- i, b, g, d, pal- n, pal- m, and ntsc-m (with pedestal or without) composite video output via two 75 bnc connectors • audio decoding: sampling rates 32, 44.1, 48 khz all mpeg-1 data rates all dolby dig...

  • Page 14: 1.2.2 Inputs

    Introduction page 1-6 reference guide: tt1260 contribution receiver st.Re.E10100.3 • audio: audio embedding in the digital video output (compressed ac-3 not supported) • vertical blanking interval (vbi) signalling support: video programming system (vps)/programme delivery control (pdc) data and pass...

  • Page 15: 1.2.3 Outputs

    Introduction reference guide: tt1260 contribution receiver page 1-7 st.Re.E10100.3 tandbergtv g.703 input (telco receivers) [option] equipped with a single bnc connector for receiving signals over a pdh telco network. Atm aal-1 ds3 input (telco receivers) [option] equipped with two bnc connectors fo...

  • Page 16: 1.2.4

    Introduction page 1-8 reference guide: tt1260 contribution receiver st.Re.E10100.3 alarm output [option] a 25-way d-type connector on the alarm relay card option (tt1260/hdc/alrm) has six relays for failure monitoring for ncp over-air. The operator can define (using the alarms menu 5) which alarm co...

  • Page 17: 1.3

    Introduction reference guide: tt1260 contribution receiver page 1-9 st.Re.E10100.3 1.3 the satellite receiver 1.3.1 typical satellite system the tt1260 satellite receiver is a component of the mpeg-2/dvb compliant range of tandberg television equipment. It is designed for use by broadcasters and dis...

  • Page 18: 1.3.4

    Introduction page 1-10 reference guide: tt1260 contribution receiver st.Re.E10100.3 figure 1.3: what the satellite receiver does 1.3.4 over-air software download (tandberg director systems) the tt1260 satellite receiver is shipped with the appropriate software installed, but it is designed to allow ...

  • Page 19: 1.4

    Introduction reference guide: tt1260 contribution receiver page 1-11 st.Re.E10100.3 1.4 the telco receiver/decoder 1.4.1 typical decoder system the decoder is a component of tandberg television’s range of equipment. It is designed for use by broadcasters and distributors of video and audio services....

  • Page 20: 1.5 Tt1260

    Introduction page 1-12 reference guide: tt1260 contribution receiver st.Re.E10100.3 the decoder can be used to receive an input signal from a public telecom network via a network adapter unit (nau). No error correction is supported at the input of the unit so a level of quality of service should be ...

  • Page 21: 1.5.3

    Introduction reference guide: tt1260 contribution receiver page 1-13 st.Re.E10100.3 1.5.3 remote control modes rs-232/rs-485 port the unit enters this state when the rs232/rs485 remote port receives a configuration change command or the remote control mode is selected in the system (menu 6); see ann...

  • Page 22: 1.6.3 Front

    Introduction page 1-14 reference guide: tt1260 contribution receiver st.Re.E10100.3 figure 1.8: front panel controls 1.6.3 front panel leds figure 1.8 shows the location of the leds on the front panel. The leds indicate the equipment status as follows: the red alarm led is used to indicate an ird fa...

  • Page 23: 1.6.6 Rear

    Introduction reference guide: tt1260 contribution receiver page 1-15 st.Re.E10100.3 dvb common interface the tt1260 common interface version has a common interface (ci) slot at the rear. The ci module has to be inserted first, before a card can be inserted. 1.6.6 rear panel inputs and outputs to the...

  • Page 24

    Introduction page 1-16 reference guide: tt1260 contribution receiver st.Re.E10100.3 blank.

  • Page 25: Contents

    Reference guide: tt1260 contribution receiver page 2-1 st.Re.E10100.3 chapter 2 2. Installing the equipment contents 2.1 read this first!................................................. 2-3 2.1.1 handling................................................. 2-3 2.1.2 installing the equipment..............

  • Page 26

    Installing the equipment page 2-2 reference guide: tt1260 contribution receiver st.Re.E10100.3 list of tables table 2.1: fuse information .................................................. 2-7 table 2.2: supply cord wiring colours ................................. 2-7 table 2.3: non standard supply ...

  • Page 27: 2.1

    Installing the equipment reference guide: tt1260 contribution receivertt1260 contribution receiver page 2-3 st.Re.E10100.3 2.1 read this first! 2.1.1 handling the tt1260 must be handled and installed carefully and thoughtfully to prevent safety hazards and damage. 2.1.2 installing the equipment ensu...

  • Page 28: 2.2

    Installing the equipment page 2-4 reference guide: tt1260 contribution receiver st.Re.E10100.3 2.2 preliminary checks 2.2.1 mechanical inspection warning… removing the covers of this equipment may invalidate any warranties, cause a safety hazard or/and affect the emc performance. Check with tandberg...

  • Page 29: 2.3

    Installing the equipment reference guide: tt1260 contribution receivertt1260 contribution receiver page 2-5 st.Re.E10100.3 2.3 installing the equipment 2.3.1 fixing the tt1260 is designed for fixed use only and has been shipped with fixing brackets suitable for a standard 19-inch rack. When installe...

  • Page 30: 2.3.3

    Installing the equipment page 2-6 reference guide: tt1260 contribution receiver st.Re.E10100.3 2.3.3 installing cables - safety power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cables at plug...

  • Page 31: 2.5.1

    Installing the equipment reference guide: tt1260 contribution receivertt1260 contribution receiver page 2-7 st.Re.E10100.3 figure 2.2: a.C. Power inlet assembly table 2.1: fuse information item specification fuse single pole, fitted in live conductor in power input filter at rear of unit. Fuse type ...

  • Page 32

    Installing the equipment page 2-8 reference guide: tt1260 contribution receiver st.Re.E10100.3 table 2.3. The inclusion of.

  • Page 33

    Installing the equipment reference guide: tt1260 contribution receivertt1260 contribution receiver page 2-9 st.Re.E10100.3 table 2.3 is for reference..

  • Page 34: 2.5.2

    Installing the equipment page 2-10 reference guide: tt1260 contribution receiver st.Re.E10100.3 table 2.3: non standard supply cord wire colours wire colour (uk) action green-and-yellow ...Must be connected to the terminal in the plug which is marked with the letter e or the safety earth symbol or c...

  • Page 35: 2.7

    Installing the equipment reference guide: tt1260 contribution receivertt1260 contribution receiver page 2-11 st.Re.E10100.3 3. Supply cord connect the d.C. Lead to the receiver input connector and then to the local d.C. Power supply. Switch on the d.C. Power supply. 2.7 protective earth/technical ea...

  • Page 36: 2.8 Signal

    Installing the equipment page 2-12 reference guide: tt1260 contribution receiver st.Re.E10100.3 2.8 signal connections 2.8.1 general caution... It is strongly recommended that the terminal marked at the rear panel of the equipment is connected to a site technical earth before any external connection...

  • Page 37

    Installing the equipment reference guide: tt1260 contribution receivertt1260 contribution receiver page 2-13 st.Re.E10100.3 figure 2.5: tt1260 signal connections frame sync hi-z rs232/rs485 frame synchronisation rs-232/rs-485 remote control asi transport streams asi transport streams analogue/digita...

  • Page 38: 2.8.2

    Installing the equipment page 2-14 reference guide: tt1260 contribution receiver st.Re.E10100.3 2.8.2 tt1260 base unit (tt1260/dirbas) rear panel view figure 2.6: typical decoder rear panel, with asi input and alarm option fitted 2.8.3 asi out two bnc sockets output asi transport streams with a maxi...

  • Page 39: 2.8.5 Frame

    Installing the equipment reference guide: tt1260 contribution receivertt1260 contribution receiver page 2-15 st.Re.E10100.3 item specification analogue output level +18 dbm nominal clipping level. Selectable in range 12 to +24 dbm. Load impedance ≥ 600 Ω balanced analogue video output this bnc socke...

  • Page 40: 2.8.6 Ethernet/web

    Installing the equipment page 2-16 reference guide: tt1260 contribution receiver st.Re.E10100.3 table 2.8: frame sync hi-z connector item specification connector type bnc 75 Ω socket connector designation frame sync pin: centre analogue black and burst input shield ground/chassis impedance last unit...

  • Page 41: 2.8.7

    Installing the equipment reference guide: tt1260 contribution receivertt1260 contribution receiver page 2-17 st.Re.E10100.3 table 2.10: remote control connector item specification connector type 9-way, d-type, male connector designation rs232/rs485 remote rs-232 rs-485 pin-outs pin 1 2 3 4 5 6 7 8 9...

  • Page 42: 2.9 Option

    Installing the equipment page 2-18 reference guide: tt1260 contribution receiver st.Re.E10100.3 table 2.12: rs-232 low-speed data connector item specification connector type 9-way, d-type, female connector designation rs232 data standards rs-232 data configuration dce pin-outs pin 1 not used pin 2 r...

  • Page 43: Contents

    Reference guide: tt1260 contribution receiver page 3-1 st.Re.E10100.3 chapter 3 3. Operating the equipment locally contents 3.1 powering the equipment ................................... 3-3 3.1.1 switching on.......................................... 3-3 3.1.2 power up operating modes.................

  • Page 44

    Operating the equipment locally page 3-2 reference guide: tt1260 contribution receiver st.Re.E10100.3 3.9.3 asi output mode..................................3-20 3.10 setting up the alarms (menu 5) ......................3-21 3.11 setting up system parameters (menu 6) ........3-22 3.12 restarting the...

  • Page 45: 3.1

    Operating the equipment locally reference guide: tt1260 contribution receiver page 3-3 st.Re.E10100.3 3.1 powering the equipment 3.1.1 switching on caution... This equipment should not be operated unless the cooling fan is working and there is free-air flow around the unit. Refer to chapter 2, secti...

  • Page 46: 3.2

    Operating the equipment locally page 3-4 reference guide: tt1260 contribution receiver st.Re.E10100.3 3.2 front panel controls and pushbuttons front panel items are described under section 1.6, guided tour. Figure 3.2: front panel controls and pushbuttons 3.3 front panel operating modes 3.3.1 genera...

  • Page 47

    Operating the equipment locally reference guide: tt1260 contribution receiver page 3-5 st.Re.E10100.3 the front panel returns to navigate mode when edit is pressed again (abort edit with no save) or when save is pressed (save modified parameter values). Processing of events from the front panel even...

  • Page 48: 3.4

    Operating the equipment locally page 3-6 reference guide: tt1260 contribution receiver st.Re.E10100.3 3.4 using the local controls 3.4.1 lcd menu descriptions detailed lcd menu descriptions are given in annex c, menus. This chapter concentrates on describing the use of the menus for local operation....

  • Page 49: 3.5

    Operating the equipment locally reference guide: tt1260 contribution receiver page 3-7 st.Re.E10100.3 3.5 setting up preset services (menu 1) 3.5.1 using preset services this group allows up to 40 services to be stored as presets. Selecting a service from the preset list in menu 1 automatically reco...

  • Page 50

    Operating the equipment locally page 3-8 reference guide: tt1260 contribution receiver st.Re.E10100.3 step action result 5 scroll to menu 2.3.3. Enter the modulation and fec rates then press save. This sets up the modulation (qpsk, 8psk, 16qam) and fec (1/2, 2/3, 3/4, 5/6, 7/8, 8/9) rates for the se...

  • Page 51: 3.6.2

    Operating the equipment locally reference guide: tt1260 contribution receiver page 3-9 st.Re.E10100.3 dvb-s2 satellite receiver (tt1260/hwo/dvbs2, tt1260/hwo/dvbs2/asi, tt1260/hwo/dvbs2/asi/if/c) table 3.8: setting up the dvb-s2 satellite receiver step action result 1 go to menu 2.2 and select sourc...

  • Page 52: 3.6.3 Atm

    Operating the equipment locally page 3-10 reference guide: tt1260 contribution receiver st.Re.E10100.3 table 3.9: tuning the terrestrial receiver step action 1 connect the cable to the cofdm input. 2 power up the unit and navigate to menu 2 input. 3 press the right pushbutton to access menu 2.1 4 pr...

  • Page 53

    Operating the equipment locally reference guide: tt1260 contribution receiver page 3-11 st.Re.E10100.3 10/100baset ip (tt1260/hwo/ip) table 3.11 steps through the set up procedure of the telco receiver using menu 2 input, and the ip input. Table 3.11: setting up the ip interface step action 1 connec...

  • Page 54: 3.7

    Operating the equipment locally page 3-12 reference guide: tt1260 contribution receiver st.Re.E10100.3 3.7 service configuration (menu 3) 3.7.1 selecting and setting up a service each transport stream may contain many services. Menu 3 allows a service to be chosen as current and the profile of its c...

  • Page 55: 3.7.3

    Operating the equipment locally reference guide: tt1260 contribution receiver page 3-13 st.Re.E10100.3 step action result 9 scroll down to menu 3.1.11 and edit the parameter for setting the video monitor aspect ratio (4:3, 16:9) and video output level (70 – 130%). Press save. Edits the parameter for...

  • Page 56: 3.7.4

    Operating the equipment locally page 3-14 reference guide: tt1260 contribution receiver st.Re.E10100.3 step action result 4 scroll to menu 3.2.4 and edit the clipping value (12 – 24 db). Press save. Edits the clipping value. 5 scroll to menu 3.2.5 and edit the ac-3 downmix parameter (surround stereo...

  • Page 57: 3.7.6 Setting

    Operating the equipment locally reference guide: tt1260 contribution receiver page 3-15 st.Re.E10100.3 table 3.17: setting up synchronous high-speed data step action result 1 go to menu 3.4 and press edit. Select the data stream pid. Selects the synchronous data stream. 2 scroll to menu 3.4.1 and ed...

  • Page 58: 3.7.9

    Operating the equipment locally page 3-16 reference guide: tt1260 contribution receiver st.Re.E10100.3 table 3.20: setting up vbi step action result 1 go to menu 3.7 and select the vbi pid. Selects the vbi component. 2 scroll down to menu 3.7.1 and edit the parameter for enabling vps insertion (enab...

  • Page 59: 3.7.11

    Operating the equipment locally reference guide: tt1260 contribution receiver page 3-17 st.Re.E10100.3 3.7.11 setting up mpeg4 video de-scrambling this feature allows the components in a scrambled service to be distributed as a clear service at the transport stream output. The ird does not decode or...

  • Page 60: 3.8

    Operating the equipment locally page 3-18 reference guide: tt1260 contribution receiver st.Re.E10100.3 3.8 setting up the conditional access/scrambling (menu 4) 3.8.1 introduction menu 4 allows the status and configuration of the conditional access (ca) module to be checked. The structure and conten...

  • Page 61: 3.8.5

    Operating the equipment locally reference guide: tt1260 contribution receiver page 3-19 st.Re.E10100.3 table 3.25: setting up the conditional access step action result 1 go to menu 4. Gains entry into the conditional access menu. 2 scroll down to menu 4.1 and edit the ras mode (fixed key mode or dsn...

  • Page 62: 3.9

    Operating the equipment locally page 3-20 reference guide: tt1260 contribution receiver st.Re.E10100.3 3.9 setting up the transport stream output (menu 4.8) 3.9.1 set-up procedure use table 3.26 to step through the transport stream output set up procedure using menu 4.8. This allows the transport st...

  • Page 63: 3.10

    Operating the equipment locally reference guide: tt1260 contribution receiver page 3-21 st.Re.E10100.3 3.10 setting up the alarms (menu 5) menu 5 allows a selection of alarms to be edited. Table 3.27 lists the alarm menus available for the qpsk satellite receiver option card. The steps and menus giv...

  • Page 64: 3.11

    Operating the equipment locally page 3-22 reference guide: tt1260 contribution receiver st.Re.E10100.3 3.11 setting up system parameters (menu 6) this menu gives access to the setup menu to set up and edit system parameters as well as the ird details menu. Table 3.28: setting up a system step action...

  • Page 65: 3.12

    Operating the equipment locally reference guide: tt1260 contribution receiver page 3-23 st.Re.E10100.3 3.12 restarting the unit the system restart submenu allows the user to reboot the unit without having to remove and insert the power cable. Table 3.30: system restart menu step action result 1 go t...

  • Page 66

    Operating the equipment locally page 3-24 reference guide: tt1260 contribution receiver st.Re.E10100.3 blank.

  • Page 67: Contents

    Reference guide: tt1260 contribution receiver page 4-1 st.Re.E10100.3 chapter 4 4. Operating the equipment remotely contents 4.1 remote control ................................................. 4-3 4.1.1 introduction ............................................ 4-3 4.1.2 remote protocol control docu...

  • Page 68

    Operating the equipment remotely page 4-2 reference guide: tt1260 contribution receiver st.Re.E10100.3 blank.

  • Page 69: 4.1 Remote

    Operating the equipment remotely reference guide: tt1260 contribution receiver page 4-3 st.Re.E10100.3 4.1 remote control 4.1.1 introduction the ird can be remotely controlled in a variety of ways. The basic control methods are: • tandberg device controller (tdc) • third-party application using tand...

  • Page 70: 4.1.5

    Operating the equipment remotely page 4-4 reference guide: tt1260 contribution receiver st.Re.E10100.3 table 4.2: configuring the serial remote port and activating remote protocol step action result 1. Go to menu 6.1 system setup menu displays ‘operating mode’ 2. Press the edit button displays ‘fron...

  • Page 71: 4.1.6

    Operating the equipment remotely reference guide: tt1260 contribution receiver page 4-5 st.Re.E10100.3 entering the oac lockout pin table 4.4: entering the oac lockout pin step action result 1. Go to menu 4.5.6 director. Displays ‘ncp lock override pin’. 2. Press edit. Displays ‘enter current pin’. ...

  • Page 72

    Operating the equipment remotely page 4-6 reference guide: tt1260 contribution receiver st.Re.E10100.3 blank.

  • Page 73: Contents

    Reference guide: tt1260 contribution receiver page 5-1 st.Re.E10100.3 chapter 5 5. Alarms contents 5.1 introduction ....................................................... 5-3 5.2 location of the alarm and lock leds ............... 5-3 5.3 alarm led and summary relay ....................... 5-3 list...

  • Page 74

    Alarms page 5-2 reference guide: tt1260 contribution receiver st.Re.E10100.3 blank.

  • Page 75: 5.1 Introduction

    Alarms reference guide: tt1260 contribution receiver page 5-3 st.Re.E10100.3 5.1 introduction there are two front panel leds that indicate the status of the tt1260. There is also one summary alarm relay and six additional alarm relays (optional). These are used to indicate abnormal performance of th...

  • Page 76

    Alarms page 5-4 reference guide: tt1260 contribution receiver st.Re.E10100.3 it is possible to signal additional alarms depending on the transport stream, input type and optional functionality in the unit. Satellite inputs: • bit error rate (ber) above (programmable) threshold. • modulation error ra...

  • Page 77: Contents

    Reference guide: tt1260 contribution receiver page 6-1 st.Re.E10100.3 chapter 6 6. Options contents 6.1 available options .............................................. 6-3 6.1.1 hardware options .................................. 6-3 6.1.2 software options ................................... 6-4 6....

  • Page 78

    Options page 6-2 reference guide: tt1260 contribution receiver st.Re.E10100.3 list of figures figure 6.1: the protocol stack.............................................. 6-6 figure 6.2: building the ethernet frame ............................... 6-7 list of tables table 6.1: hardware options (input...

  • Page 79: 6.1 Available

    Options reference guide: tt1260 contribution receiver page 6-3 st.Re.E10100.3 6.1 available options 6.1.1 hardware options these options require extra hardware to be fitted to the unit. Contact the customer services helpdesk for details (see preliminary pages). There are two mezzanine option slots a...

  • Page 80: 6.1.2 Software

    Options page 6-4 reference guide: tt1260 contribution receiver st.Re.E10100.3 6.1.2 software options table 6.3 list the purchasable software options for enhanced functionality. Table 6.3: software options marketing code description tt1260/swo/hsether high speed ethernet data output (data piping). Tt...

  • Page 81: 6.2

    Options reference guide: tt1260 contribution receiver page 6-5 st.Re.E10100.3 6.2 hardware enabled options (input cards) 6.2.1 asi input (tt1260/hwo/asi) the asi input card supports asi transport stream on two bncs. The transport stream can be sourced from either input 1, input 2 or automatically se...

  • Page 82: 6.2.4

    Options page 6-6 reference guide: tt1260 contribution receiver st.Re.E10100.3 6.2.4 cofdm input (tt1260/hwo/cofdm678) the cofdm digital terrestrial input card demodulates cofdm signals. The board is able to be used in all rf channel bandwidths (6, 7 and 8 mhz). 6.2.5 ttv g.703 input card (tt1260/hwo...

  • Page 83: 6.2.7

    Options reference guide: tt1260 contribution receiver page 6-7 st.Re.E10100.3 figure 6.2: building the ethernet frame 6.2.7 atm aal-1 e3 telco input (tt1260/hwo/atm-e3) this provides transmission of mpeg-2 ts packets (respectively rs coded mpeg-2 ts packets) over pdh links using atm cells, this part...

  • Page 84: 6.2.12

    Options page 6-8 reference guide: tt1260 contribution receiver st.Re.E10100.3 an if monitor bnc input is provided with the tt1260/hwo/dvbs2/asi/if/c option. This option also gives a constellation i and q monitor output 1 . Enabling the constellation output mode disables the ability of the ird to dec...

  • Page 85: 6.4

    Options reference guide: tt1260 contribution receiver page 6-9 st.Re.E10100.3 input specification pin 15 pin 16 pin 17 pin 18 pin 19 pin 20 pin 21 pin 22 pin 23 pin 24 pin 25 relay 2 – normally open (closed on alarm) relay 2 – normally closed (open on alarm) relay 3 – common relay 4 – normally open ...

  • Page 86: 6.4.9

    Options page 6-10 reference guide: tt1260 contribution receiver st.Re.E10100.3 6.4.9 dvb-s2 8psk software licence (tt1260/swo/dvbs2/8psk) software key licence for tt1260/hwo/dvbs2, tt1260/hwo/dvbs2/asi, tt1260/hwo/dvbs2/asi/if/c enabling the dvb-s2 8psk mode. Also requires the tt1260/swo/dvbs2 qpsk ...

  • Page 87: 6.5.4

    Options reference guide: tt1260 contribution receiver page 6-11 st.Re.E10100.3 6.5.4 director functionality (tt1260/swo/dir) this option enables director (version 4) functionality. 6.5.5 directorv5 functionality (tt1260/swo/dirv5) this option enables director (version 5) functionality. 6.5.6 provide...

  • Page 88

    Options page 6-12 reference guide: tt1260 contribution receiver st.Re.E10100.3 blank.

  • Page 89: Contents

    Reference guide: tt1260 contribution receiver page 7-1 st.Re.E10100.3 chapter 7 7. Preventative maintenance and fault- finding contents 7.1 routine checks................................................. 7-3 7.1.1 cooling fan ........................................... 7-3 7.1.2 cleaning...............

  • Page 90

    Preventative maintenance and fault-finding page 7-2 reference guide: tt1260 contribution receiver st.Re.E10100.3 blank.

  • Page 91: 7.1 Routine

    Preventative maintenance and fault-finding reference guide: tt1260 contribution receiver page 7-3 st.Re.E10100.3 7.1 routine checks 7.1.1 cooling fan there are no routine checks associated with this equipment other than to ensure that the unit is adequately cooled. This equipment must never be opera...

  • Page 92: 7.2.2 Replacement

    Preventative maintenance and fault-finding page 7-4 reference guide: tt1260 contribution receiver st.Re.E10100.3 6. When the product exhibits a distinct change in performance. 7. If the equipment has been subject to a lightning strike or power surge. 7.2.2 replacement parts when replacement parts ar...

  • Page 93: 7.4 Fault-Finding

    Preventative maintenance and fault-finding reference guide: tt1260 contribution receiver page 7-5 st.Re.E10100.3 7.4 fault-finding 7.4.1 general the information contained in this chapter is intended to isolate the unit as the faulty equipment if a system failure occurs. If the following information ...

  • Page 94: 7.5

    Preventative maintenance and fault-finding page 7-6 reference guide: tt1260 contribution receiver st.Re.E10100.3 7.5 changing the equipment fuse 7.5.1 a.C. User accessible fuse replacement caution... This product should be operated only from the type of power source indicated on the marking label. I...

  • Page 95: 7.5.2

    Preventative maintenance and fault-finding reference guide: tt1260 contribution receiver page 7-7 st.Re.E10100.3 figure 7.2: fuse carrier if the replacement fuse also blows, do not continue. Disconnect the equipment and contact tandberg customer services (see preliminary pages) for advice. 7.5.2 d.C...

  • Page 96: 7.6 Disposal

    Preventative maintenance and fault-finding page 7-8 reference guide: tt1260 contribution receiver st.Re.E10100.3 7.6 disposal 7.6.1 moulded plugs if the moulded plug fitted to the mains cable supplied with this equipment is not required, use another cable. If the supplied plug is to be changed, cut ...

  • Page 97

    Reference guide: tt1260 contribution receiver page a-1 st.Re.E10100.3 annex a a. Glossary the following list covers most of the abbreviations, acronyms and terms as used in tandberg television limited manuals, user and reference guides. All terms may not be included in this reference guide. µ m micr...

  • Page 98

    Glossary page a-2 reference guide: tt1260 contribution receiver st.Re.E10100.3 atm asynchronous transfer mode: a connection orientated, cell based, data transport technology designed for broadband isdn (b-isdn). It provides a circuit-switched bandwidth- on-demand carrier system, with the flexibility...

  • Page 99

    Glossary reference guide: tt1260 contribution receiver page a-3 st.Re.E10100.3 c-band the portion of the electromagnetic spectrum, which spans the frequency range of approximately 4 ghz to 6 ghz. Used by communications satellites. Preferred in tropical climates because it is not susceptible to fadin...

  • Page 100

    Glossary page a-4 reference guide: tt1260 contribution receiver st.Re.E10100.3 dce data communications equipment: typically a modem. It establishes, maintains and terminates a session on a network but in itself is not the source (originator) or destination (end receiving unit) of signals (e.G. A com...

  • Page 101

    Glossary reference guide: tt1260 contribution receiver page a-5 st.Re.E10100.3 earth technical earth: ensures that all equipment chassis within a rack are at the same potential, usually by connecting a wire between the technical earth terminal and a suitable point on the rack. This is sometimes know...

  • Page 102

    Glossary page a-6 reference guide: tt1260 contribution receiver st.Re.E10100.3 ftp file transfer protocol:a protocol used to transfer files over a tcp/ip network (internet, unix, etc.). For example, after developing the html pages for a web site on a local machine, they are typically uploaded to the...

  • Page 103

    Glossary reference guide: tt1260 contribution receiver page a-7 st.Re.E10100.3 ird integrated receiver decoder: the receiver with an internal mpeg decoder, which is connected to the subscriber’s tv. The ird is responsible for receiving and de-multiplexing all signals. The unit receives the incoming ...

  • Page 104

    Glossary page a-8 reference guide: tt1260 contribution receiver st.Re.E10100.3 lvds low voltage differential signal: lvds is a generic multi-purpose interface standard for high speed / low power data transmission. It was standardised in ansi/tia/eia-644-1995 standard (aka rs-644). Macroblock a 16x16...

  • Page 105

    Glossary reference guide: tt1260 contribution receiver page a-9 st.Re.E10100.3 network in the context of broadcasting: a collection of mpeg-2 transport stream multiplexes transmitted on a single delivery system, for example, all digital channels on a specific cable system. Nicam near instantaneously...

  • Page 106

    Glossary page a-10 reference guide: tt1260 contribution receiver st.Re.E10100.3 pel picture element: also known as a pixel. The smallest resolvable rectangular area of an image either on a screen or stored in memory. On-screen, pixels are made up of one or more dots of colour. Monochrome and grey-sc...

  • Page 107

    Glossary reference guide: tt1260 contribution receiver page a-11 st.Re.E10100.3 psi program specific information: consists of normative data, which is necessary for the demultiplexing of transport streams and the successful regeneration of programs. (see also: si). Psip program system information pr...

  • Page 108

    Glossary page a-12 reference guide: tt1260 contribution receiver st.Re.E10100.3 sfn single frequency network: the sfn technique allows largegeographic areas to be served with a common transmission multiplex. All transmitters in the network are synchronously modulated with the same signal and they al...

  • Page 109

    Glossary reference guide: tt1260 contribution receiver page a-13 st.Re.E10100.3 tot time offset table: this optional si table supports the use of local offsets as well as the utc time/date combination. The purpose of the table is to list by country the current offset from utc and the next expected c...

  • Page 110

    Glossary page a-14 reference guide: tt1260 contribution receiver st.Re.E10100.3 blank.

  • Page 111: Contents

    Reference guide: tt1260 contribution receiver page b-1 st.Re.E10100.3 annex b b. Technical specification contents b.1 output ...............................................................B-3 b.1.1 international television standards.........B-3 b.1.2 supported video bitrates .......................B...

  • Page 112

    Technical specification page b-2 reference guide: tt1260 contribution receiver st.Re.E10100.3 b.9 environmental ................................................ B-26 b.9.1 conditions ........................................... B-26 b.9.2 physical............................................... B-27 b...

  • Page 113: B.1 Output

    Technical specification reference guide: tt1260 contribution receiver page b-3 st.Re.E10100.3 b.1 output b.1.1 international television standards two composite video outputs are provided at the rear panel. These carry identical video. The standard is selectable to pal- i, b, g, d, n, m and ntsc-m (w...

  • Page 114: B.1.4 Performance

    Technical specification page b-4 reference guide: tt1260 contribution receiver st.Re.E10100.3 table b.3: supported video resolutions 625-line, 25 frame/s 525-line, 30 (29.97) frame/s 720 pixels x 608 active lines 720 pixels x 512 active lines 4:2:2 mode only 720 pixels x 576 active lines 720 pixels ...

  • Page 115: B.2

    Technical specification reference guide: tt1260 contribution receiver page b-5 st.Re.E10100.3 • support for closed captioning (atsc, divicom and ttv proprietary mpeg carriage protocol) • insertion test signal (its) insertion (ccir and fcc/uk) • world system teletext (wst) • inverted teletext (wst) •...

  • Page 116: B.2.3

    Technical specification page b-6 reference guide: tt1260 contribution receiver st.Re.E10100.3 • sampling rates (khz): 32, 44.1, 48 • maximum compressed data rate: 384 kbit/s (layer ii) b.2.3 dolby digital ac-3 audio the tt1260 is able to decode and output the primary stereo pair of a dolby digital a...

  • Page 117: B.3.3 Digital

    Technical specification reference guide: tt1260 contribution receiver page b-7 st.Re.E10100.3 table b.5: analogue audio performance specifications parameter conditions limit gain 0 dbm input level ± 1 db frequency response 100 hz - 15 khz, 0 dbm input level ± 0.2 db 20 hz - 20 khz, 0 dbm input level...

  • Page 118: B.3.7

    Technical specification page b-8 reference guide: tt1260 contribution receiver st.Re.E10100.3 the lip sync error (delay from presentation of video until presentation of audio) introduced by the receiver is in the range of ±5 ms. The lip sync delay between stereo pair 1 and 2 is ±2 ms because the pts...

  • Page 119: B.4 Internal

    Technical specification reference guide: tt1260 contribution receiver page b-9 st.Re.E10100.3 b.4 internal decoder the tt1260 contains an internal decoder. A packet demultiplexer selects audio, video and ancillary services from the stream received from the digital demodulator. A service filter reduc...

  • Page 120: B.5

    Technical specification page b-10 reference guide: tt1260 contribution receiver st.Re.E10100.3 b.5 input option specifications b.5.1 qpsk satellite receivers (tt1260/hwo/qpsk) general table b.9: qpsk satellite receiver input specification parameter specification l-band input safety status selv numbe...

  • Page 121

    Technical specification reference guide: tt1260 contribution receiver page b-11 st.Re.E10100.3 table b.10: qpsk l-band satellite input — c/n ratio convolutional fec rate c/n ratio (db) in if loop for correct mpeg-2 system operation 1/2 4.5 2/3 5.0 3/4 5.5 5/6 6.0 7/8 6.4 c/n ratio is referred to use...

  • Page 122: B.5.2

    Technical specification page b-12 reference guide: tt1260 contribution receiver st.Re.E10100.3 b.5.2 16qam/qpsk satellite receivers (4-input) (tt1260/hwo/hom) the hmo card is a 16qam, 8psk, qpsk, bpsk input module. This card provides a complete digital front end board for dvb-s, dsng and other contr...

  • Page 123: B.5.3

    Technical specification reference guide: tt1260 contribution receiver page b-13 st.Re.E10100.3 table b.14: demodulator parameter specification signal format for dvb modes en 301 210 receive spectrum sense normal & inverted spectrum capability automatic fec search bpsk/qpsk dvbs modes only receive sy...

  • Page 124

    Technical specification page b-14 reference guide: tt1260 contribution receiver st.Re.E10100.3 parameter specification total l-band input power oscillator power at the l-band input if monitor input safety status selv number of inputs 0 (tt1260/hwo/dvbs2) 1 (tt1260/hwo/dvbs2/asi/if/c) input connector...

  • Page 125

    Technical specification reference guide: tt1260 contribution receiver page b-15 st.Re.E10100.3 parameter specification rs = symbol-rate (msymbol/s) dvb-s2 phase noise tolerance 11 -25 dbc/hz at δ f = 100 hz -50 dbc/hz at δ f = 1 khz -73 dbc/hz at δ f = 10 khz -93 dbc/hz at δ f = 100 khz -103 dbc/hz ...

  • Page 126: B.5.4

    Technical specification page b-16 reference guide: tt1260 contribution receiver st.Re.E10100.3 lnb power and control the ird provides lnb power and control signals through the active rf input connector. Lnb power and controls are enabled through the satellite input menu, see annex c, menus . The ird...

  • Page 127: B.5.5

    Technical specification reference guide: tt1260 contribution receiver page b-17 st.Re.E10100.3 table b.21: cofdm parameters parameter specification guard interval 1/32, 1/16, 1/8, 1/4 carrier mode 2 k, 8 k hierarchy stream high and low priority hierarchy mode none, α = 1, α = 2, α = 4 carrier modula...

  • Page 128: B.5.7

    Technical specification page b-18 reference guide: tt1260 contribution receiver st.Re.E10100.3 b.5.7 atm aal-1 ds3 atm input (tt1260/hwo/atm-ds3) this provides reception of mpeg-2 transport stream packets, respectively rs coded mpeg-2 ts packets, over pdh links using atm cells, this particular versi...

  • Page 129

    Technical specification reference guide: tt1260 contribution receiver page b-19 st.Re.E10100.3 parameter specification frequency tuning range 14 fc = 950 to 2150 mhz tuning step 100 khz carrier frequency search range 0 to ± 5 mhz receive spectrum sense normal and inverted power input power level per...

  • Page 130: B.5.10

    Technical specification page b-20 reference guide: tt1260 contribution receiver st.Re.E10100.3 table b.28: qpsk bitrate r188 limits (mbit/s) fec r188min r188max 1/2 1.000000 41.470588 2/3 1.228758 55.294118 3/4 1.382353 62.205882 5/6 1.535948 69.117647 7/8 1.612745 72.573529 lnb power and control th...

  • Page 131

    Technical specification reference guide: tt1260 contribution receiver page b-21 st.Re.E10100.3 connector type 8 way rj-45 connector designation 10/100 bt signal type 10/100baset ethernet (ieee 802.3/802.3u) data rate 1.5 – 50 mbit/s.

  • Page 132: B.6 Output

    Technical specification page b-22 reference guide: tt1260 contribution receiver st.Re.E10100.3 b.6 output options b.6.1 high-speed data (tt1260/hwo/hsdata) high-speed data (synchronous data) can be carried in a transport stream as private data. This is then extracted from the transport stream and ou...

  • Page 133: B.7

    Technical specification reference guide: tt1260 contribution receiver page b-23 st.Re.E10100.3 b.7 frame sync connector the decoder can frame lock to an external video source. The frame information is input as a composite synchronous signal, with or without active video. The user can offset the sync...

  • Page 134: B.8.2 Audio

    Technical specification page b-24 reference guide: tt1260 contribution receiver st.Re.E10100.3 digital video table b.36: digital video output connectors item specification safety status selv connector type bnc, female, 75 Ω connector designation sdi 1 sdi 2 output standard (usa) ansi/smpte 292m sdi ...

  • Page 135: B.8.4

    Technical specification reference guide: tt1260 contribution receiver page b-25 st.Re.E10100.3 b.8.4 rs-232/rs-485 remote control connector table b.39: rs232/485 control connector item specification safety status selv connector type 9-way d-type, male connector designation rctrl rs-232/485 standard ...

  • Page 136: B.8.7

    Technical specification page b-26 reference guide: tt1260 contribution receiver st.Re.E10100.3 b.8.7 summary alarm connector table b.42: summary relay alarm output specification item specification safety status selv connector type 9-way d-type female connector designation: alarm contact configuratio...

  • Page 137: B.9.2 Physical

    Technical specification reference guide: tt1260 contribution receiver page b-27 st.Re.E10100.3 operational specification storage/transportation temperature -20 ° c to +70 ° c (-4 ° f to +158 ° f) humidity 0% to 95% (non-condensing) b.9.2 physical table b.45: physical parameters parameter specificati...

  • Page 138: B.10.2

    Technical specification page b-28 reference guide: tt1260 contribution receiver st.Re.E10100.3 b.10.2 d.C. Supply input (-48 vdc version) notes... 1. Only models tt1260/cibas/48 and tt1260/dirbas/48 use a d.C. Power supply. 2. Ensure correct polarity is maintained. 3. The unit must have a protective...

  • Page 139: B.12 Compliance

    Technical specification reference guide: tt1260 contribution receiver page b-29 st.Re.E10100.3 b.12 compliance 18 b.12.1 safety this equipment has been designed and tested to meet the requirements of the following: en 60950-1 european information technology equipment - safety. Iec 60950-1 internatio...

  • Page 140: B.12.4 C-Tick

    Technical specification page b-30 reference guide: tt1260 contribution receiver st.Re.E10100.3 b.12.4 c-tick mark the c-tick mark is affixed to denote compliance with the australian radiocommunications (compliance and labelling – incidental emissions) notice made under s.182 of radiocommunications a...

  • Page 141: B.12.7 Materials

    Technical specification reference guide: tt1260 contribution receiver page b-31 st.Re.E10100.3 . B.12.7 materials declarations tandberg television products are designed and manufactured in keeping with good environmental practise. Our component and materials selection policy prohibits the use of a r...

  • Page 142: B.12.8 Equipment

    Technical specification page b-32 reference guide: tt1260 contribution receiver st.Re.E10100.3 b.12.8 equipment disposal general dispose of this equipment safely at the end of its life. Local codes and/or environmental restrictions may affect its disposal. Regulations, policies and/or environmental ...

  • Page 143: Contents

    Reference guide: tt1260 contribution receiver page c-1 st.Re.E10100.3 annex c c. Menus contents c.1 lcd menus ...................................................... C-3 c.1.1 using the menus ................................... C-3 c.1.2 menu descriptions ................................ C-3 c.2 main...

  • Page 144

    Menus page c-2 reference guide: tt1260 contribution receiver st.Re.E10100.3 table c.20: sync data menu ............................................. C-21 table c.21: high speed data over ethernet menu ........... C-21 table c.22: teletext menu ................................................. C-21 t...

  • Page 145: C.1 Lcd

    Menus reference guide: tt1260 contribution receiver page c-3 st.Re.E10100.3 c.1 lcd menus c.1.1 using the menus detailed description of the use of menus is given in chapter 3, operating the equipment locally . C.1.2 menu descriptions this annex describes the front panel lcd menus. When the unit is f...

  • Page 146: C.3

    Menus page c-4 reference guide: tt1260 contribution receiver st.Re.E10100.3 c.3 the menu structure figure c.1: menu structure 2.1 input quality mer bargraph 2.1.1 p-v ber bargraph 2.1.2 post rs errors 2.2 input source 2.2.1 guard interval 2.2.2 carrier mode 2.2.3 spectrum 2.2.4 auto detect 2.3 input...

  • Page 147: C.4

    Menus reference guide: tt1260 contribution receiver page c-5 st.Re.E10100.3 c.4 presets menu (menu 1) the presets menu contains up to 40 editable preset numbers in the range 01 – 40. Selecting a numbered service via the presets menu automatically reconfigures the input of the ird. Each preset can ha...

  • Page 148

    Menus page c-6 reference guide: tt1260 contribution receiver st.Re.E10100.3 menu # display title: input description 2.1.2 preber -1 -3 -5 1.0 e-8 xxxxxxxxxxx xxxxxxxxxxx is a bar-graph indicating the current level of pre- viterbi ber (10 x -1 to –5 range) 2.2 select source x x is the editable input ...

  • Page 149: C.5.3

    Menus reference guide: tt1260 contribution receiver page c-7 st.Re.E10100.3 c.5.3 qpsk/asi input option (tt1260/hwo/qpsk/asi) when a qpsk/asi input interface is used, the input menu allows the user to select the source and edit qpsk parameters. Table c.5: qpsk/asi ip menu menu # display title: input...

  • Page 150: C.5.4

    Menus page c-8 reference guide: tt1260 contribution receiver st.Re.E10100.3 menu # display title: input description 2.4.4 lnb power xxxxxxx at yyy xxxxxxx sets the lnb power for source 2 ( on , off , boosted ) boosted provides 1v extra power over the on setting yyy selects the rating of the power ou...

  • Page 151: C.5.5

    Menus reference guide: tt1260 contribution receiver page c-9 st.Re.E10100.3 c.5.5 10/100baset ip input option (tt1260/hwo/ip) when a 10/100baset input interface is used, the input menu allows the user to edit the set up parameters. Table c.7: ip input menu menu # display title: input description 2 w...

  • Page 152: C.5.7

    Menus page c-10 reference guide: tt1260 contribution receiver st.Re.E10100.3 menu # display title: input description 2.1.2 xxxx xxxx is a status display of the following alarms for the input “oorg ” = atm_rx_out_of_regulation “sqni ” = atm_seq_num_invalid “mscl ” = atm_missing_cells “ralm ” = atm_pd...

  • Page 153: C.5.8

    Menus reference guide: tt1260 contribution receiver page c-11 st.Re.E10100.3 c.5.8 cofdm input option (tt1260/hwo/cofdm678) when a cofdm interface is used, the input menu allows the user to edit the parameters. Table c.10: cofdm678 menu menu # display title: input description 2 wwwwwwwwww zzz tid xx...

  • Page 154: C.5.9

    Menus page c-12 reference guide: tt1260 contribution receiver st.Re.E10100.3 c.5.9 higher order modulation input option (tt1260/hwo/hom) when a higher-order modulation interface is used, the input menu allows the user to edit the parameters. Table c.11: higher-order modulation input menu menu # disp...

  • Page 155: C.5.10

    Menus reference guide: tt1260 contribution receiver page c-13 st.Re.E10100.3 menu # display title: input description 2.5.8 lnb 22 khz yy yy is the low noise block ( enable or disable ) for source 3 2.5.9 search range zz zz is the search range in khz for source 3 2.6 lnb rr rr is the lnb frequency in...

  • Page 156

    Menus page c-14 reference guide: tt1260 contribution receiver st.Re.E10100.3 menu # display title: input description 2.1.5 signal level xx xx is the signal level 2.2 select source xx xx is 1 , 2 , 3 or 4 for tt1260/hwo/dvbs2 xx is 1 , 2 , 3 , if , asi 1 or asi 2 for tt1260/hwo/dvbs2/asi/if/c 2.3 lnb...

  • Page 157

    Menus reference guide: tt1260 contribution receiver page c-15 st.Re.E10100.3 menu # display title: input description xxxx xxxx valid values of the currently selected modulation type. For auto fec, the receiver searches for and locks to the correct fec rate for the received carrier. 2.5.4 roll off vv...

  • Page 158: C.5.11

    Menus page c-16 reference guide: tt1260 contribution receiver st.Re.E10100.3 table c.13: dvb-s2/asi/if/c input menu menu # display title: input description 2, 2.1, 2.2, 2.3, 2.4, 2.5 as described in table above ( table c.12 ). 2.6 i/f frequency 2.6.1 symbol rate xx.Xxxxxx msymb/s sets the symbol rat...

  • Page 159: C.6

    Menus reference guide: tt1260 contribution receiver page c-17 st.Re.E10100.3 menu # display title: input description xxxx 2.1.9 clear statistics initiates a reset of the packet tracking menus 2.1.3, 2.1.4, and 2.1.5. 2.2 udp port number xxxxx xxxxx shows the editable udp port number on which the ip ...

  • Page 160

    Menus page c-18 reference guide: tt1260 contribution receiver st.Re.E10100.3 menu # display title: video description 625 line output yyyyy yyyyy is the editable output format pal-b/g/i , pal-n , pal-n cmb 3.1.5 default line standard xxx fail mode yyyyyyyyyyyy xxx is the editable default line output ...

  • Page 161: C.6.3

    Menus reference guide: tt1260 contribution receiver page c-19 st.Re.E10100.3 c.6.3 audio 1 menu (menu 3.2) the audio 1 signal status submenu contains information about the audio format and status of the currently decoded audio stream on the primary audio output. Table c.17: audio 1 menu menu # displ...

  • Page 162: C.6.5

    Menus page c-20 reference guide: tt1260 contribution receiver st.Re.E10100.3 menu # display title: audio 02 description 3.3.5 ac-3 downmix method xxxxxxxxxxxxx xxxxxxxxxxxxx is the editable dolby digital ac-3 downmix parameter ( surround stereo , conventional stereo ) 3.3.6 attenuation xxxx xxxx is ...

  • Page 163: C.6.7

    Menus reference guide: tt1260 contribution receiver page c-21 st.Re.E10100.3 table c.20: sync data menu menu # display title: async data description 3.4 ww streams pid xxxx yyyyyyyyyyy ww displays the number of high-speed data streams present xxxx is the editable hsd pid yyyyyyyyyyy is the stream st...

  • Page 164: C.6.9

    Menus page c-22 reference guide: tt1260 contribution receiver st.Re.E10100.3 c.6.9 vbi menu (menu 3.7) the vbi status submenu displays the current status of the vbi components. Note… the vitc menu functionality is not supported in software version 1.0.0. Table c.23: vbi menu menu # display title: vb...

  • Page 165: C.6.10

    Menus reference guide: tt1260 contribution receiver page c-23 st.Re.E10100.3 c.6.10 pcr pid menu (menu 3.8) the pcr pid submenu displays the program clock reference packet identifier and its status. Table c.24: pcr pid menu menu # display title: pcr pid description 3.8 pcr pid xxxx yyyyyyyyyy xxxx i...

  • Page 166: C.7

    Menus page c-24 reference guide: tt1260 contribution receiver st.Re.E10100.3 c.7 ca menu (menu 4) the ca menu allows the user to display and edit the conditional access parameters. Note: ca menu options are dependent on the hardware option fitted. Table c.27: ca menu menu # display title: ca descrip...

  • Page 167: C.8

    Menus reference guide: tt1260 contribution receiver page c-25 st.Re.E10100.3 c.8 alarms menu (menu 5) the alarms submenu allows the selection of alarm conditions to trigger the alarm relay. Note… the alarm menus displayed are dependent on the hardware input card type fitted. Table c.28: alarm status...

  • Page 168: C.9 System

    Menus page c-26 reference guide: tt1260 contribution receiver st.Re.E10100.3 c.9 system menus c.9.1 system overview menu (menu 6) the system overview submenu displays the system date and time. Table c.29: system overview menu menu # display title: setup description 6 date: xx/xx/xxxx time: yy:yy:yy ...

  • Page 169: C.9.3

    Menus reference guide: tt1260 contribution receiver page c-27 st.Re.E10100.3 c.9.3 ird details menu (menu 6.2) the ird details submenu displays the software, firmware, hardware, pld version and electronic serial number of the ird. Table c.31: ird details menu menu # display title: ird details descri...

  • Page 170

    Menus page c-28 reference guide: tt1260 contribution receiver st.Re.E10100.3 blank.

  • Page 171

    Reference guide: tt1260 contributiion receiver page d-1 st.Re.E10100.3 annex d d. Language abbreviations languages are shown in alphabetical order. No language abbreviation 5 arabic ara basa bas 14 bengali ben 135 chinese chi 19 czech cze 21 danish dan 82 dutch dut 25 english eng 31 finnish fin 34 f...

  • Page 172

    Language abbreviations page d-2 reference guide: tt1260 contributiion receiver st.Re.E10100.3 the following non-iso 1 languages are supported. Note… only applicable for a transport stream going to an alteia receiver. Language abbreviation main one aux two international sound int audio 1 aaa audio 2 ...

  • Page 173: Contents

    Reference guide: tt1260 contribution receiver page e-1 st.Re.E10100.3 annex e e. Using the tt1260 with the tandberg directorv5 system contents e.1 configuring the tt1260 for use with tandberg directorv5 ....................................E-3 e.1.1 getting started.......................................

  • Page 174

    Using the tt1260 with the tandberg directorv5 system page e-2 reference guide: tt1260 contribution receiver st.Re.E10100.3 blank.

  • Page 175: E.1

    Using the tt1260 with the tandberg directorv5 system reference guide: tt1260 contribution receiver page e-3 st.Re.E10100.3 e.1 configuring the tt1260 for use with tandberg directorv5 e.1.1 getting started you must have videoguard ca, a director smart card and be tuned to a director stream. Caution… ...

  • Page 176: E.2

    Using the tt1260 with the tandberg directorv5 system page e-4 reference guide: tt1260 contribution receiver st.Re.E10100.3 e.2 response to over-air commands e.2.1 scope of this section this section describes the receiver’s response to over-air commands. E.2.2 display on-screen display (osd) messages...

  • Page 177: E.2.7

    Using the tt1260 with the tandberg directorv5 system reference guide: tt1260 contribution receiver page e-5 st.Re.E10100.3 e.2.7 set emergency channel sets the service to use in the event of a selection failure. Is activated after a specified time has elapsed. If not set, the power up channel is ass...

  • Page 178

    Using the tt1260 with the tandberg directorv5 system page e-6 reference guide: tt1260 contribution receiver st.Re.E10100.3 blank.

  • Page 179

    Reference guide: tt1260 contribution receiver page f-1 st.Re.E10100.3 annex f f. Factory defaults units are shipped with the following factory default parameters. Some of the input card parameters are specific to the hardware option fitted. These can be restored at any time using the system menu. Al...

  • Page 180

    Factory defaults page f-2 reference guide: tt1260 contribution receiver st.Re.E10100.3 menu page description default #2 input ttv g.703 2.2 reed- solomon disabled 2.2.1 interleaver disabled 2.2.2 signal level normal #3 service 3.1.4 525line output ntsc-m 3.1.4 625 line output pal b/g/i 3.1.5 default...

  • Page 181

    Factory defaults reference guide: tt1260 contribution receiver page f-3 st.Re.E10100.3 menu page description default 3.7.1 vps enabled 3.7.2 wss enabled 3.7.3 vitc insertion gop 3.7.4 vitc 525 line 14 and 16 3.7.4 vitc 625 line 19 and 21 3.7.5 video index enabled 3.7.6 amol 1 and 2 enabled 3.7.7 clo...

  • Page 182

    Factory defaults page f-4 reference guide: tt1260 contribution receiver st.Re.E10100.3 blank.