Tannoy V8 User Manual - page 14
11. Technical Specifications
Frequency response (1) +/ - 3dB 85Hz – 22kHz
65Hz – 22kHz (with Tx1/TDX2 controller)
-10dB Point
51Hz (48Hz with Tx1/TDX2)
Recommended Amplifier Power
100 - 260 watt / 8 ohm
Power
Handling
Average (2) Programme Peak (10ms)
130 watt
260 watt 520 watt
Sensitivity
(1)
2.83 volt @ 1m
92 dB (anechoic)
95 dB (half space)
Maximum SPL (3)
Average Peak
@ 1m
113
dB 119
dB
Impedance Nominal 8.0
ohm
DI Averaged (PCQ)
9.11, 250 Hz - 16 kHz
@ 1kHz (ISO)
7.8
@
2kHz
(ISO)
8.3
@
4kHz
(ISO)
9.5
@
8kHz
(ISO)
11.2
@ 16kHz (ISO)
13.4
Q Averaged (PCQ)
9.93, 250 Hz - 16 kHz
@ 1kHz (ISO)
6
@
2kHz
(ISO)
6.8
@
4kHz
(ISO)
8.9
@
8kHz
(ISO)
13.2
@ 16kHz (ISO)
21.9
Distortion
0.1
Full
Power
2nd
Harmonic
3rd
Harmonic
250
Hz
0.141%
0.126%
1000
Hz
0.251%
0.794%
10000
Hz
1.340%
0.251%
0.01
Full
Power
2nd
Harmonic
3rd
Harmonic
250
Hz
0.100%
0.112%
1000
Hz
0.100%
0.56%
10000
Hz
0.56%
0.178%
Driver Complement
1 x 8” (200mm) Constant Directivity Dual Concentric
Type
number
2062
Crossover Point
Passive 1.7 kHz
4
th
order high pass, 2
nd
order low pass
Dynamic
HF
protection
Enclosure
17 litre vented, Birch plywood
Finish
Textured black paint (optional in white)
Protective
Grille
Foam covered powder coated perforated steel.
Connectors
2 x NL4MP, IN/OUT
Fittings
Recessed rear mounted carrying handle,
Blanking plate allows installation of a 35mm pole-mounting socket,
2 x M10 inserts for yoke mount, 4 x M10 flying inserts, 4 x M10 brack
(to suit Tannoy or Omnimount 50
bracket)
Dimensions
388mm(H) x 280mm(W) x 275mm(D)
15.28”(H)
x
11.02”(W)
x
10.83”(D)
Weight
8.2 Kg (18 lbs)
NOTES:
(1) Average over stated bandwidth. Measured at 1m on axis.
(2) Long term power handling capacity as defined in EIA standard RS - 426A.
(3) Unweighted pink noise input, measured at 1m in an anechoic chamber.
All Tannoy V Series products can be used with the Tannoy TDX2 Digital Controller for optimum system performance and when
being used with various sub bass systems. Please visit our website at
www.tannoy.com
for further details
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will
always equal or exceed the published specifications, which Tannoy reserves the right to alter without prior notice.
Please verify the latest specifications when dealing with critical applications.
12.4 SECUR ET – VEB Eyebolt
The Tannoy V8 loudspeaker can be flown with high
quality VEB M10 eyebolts with collar to
BS4278:1984.
To install the VEB M10 eyebolts remove the
original M10 counter sunk screws from the
locations you wish to install the VEB M10
eyebolts. Then replace these counter sunk M10
screws with the VEB M10 eyebolts. The M10
insert on the rear of the cabinet also accepts a
VEB M10 eyebolt and should only be used for
tilting the loudspeaker to the desired angle.
Important: It is imperative for safety reasons
that two eyebolts linked to two independently
fixed straps are used per cabinet. If flying one
cabinet above another, the cabinet must be
used in a landscape orientation. The correct
method is shown in figure 2.
Never attempt to use formed eyebolts i.e.
formed from a steel rod and bent into an eye.
FIG 1.
FIG 2.
FIG 2.
P
Enfocus Software - Customer Support