TARAL 16M Owner's Manual - page 11
(11)
6- MAINTENANCE
6.1- PERIODIC MAINTENACE
The procedures explained in this section should be performed in the recommended time intervals (“Hour” means real
operation hour). Use SAE EP90 for oil. Check the oil level using the oil level point. Do not overfill.
Engine: Read the engine manual.
Air filter: Read the engine manual.
Lubricate the parts stated below every 50 hours.
1. The pin for locking- releasing the handle bar: Lubricate the point for lubricating grease.
2. The pin for adjusting the height of the handle bar: Lubricate the point for lubricating grease.
3. PTO shafts: Lubricate the shafts with keyways a small amount of grease. Fill the necessary parts with grease before
attaching the equipments.
Gearbox: By removing the filling tap (1) check the oil level. The oil level should be near to the upper edge of the
filling tap.
Note: Check the oil level 10 minutes after the engine is stopped and the motor-hoe is in the horizontal position.
Check the adjustments below:
Every 600 hours change the oil. Remove the emptying tap (2) under the gearbox and remove also the filling tap (1) to
change the oil easily. Wait 10 minutes for emptying. Placing the lower tap to its position fill with the oil. It is
recommended to change oil after a long period of operation when it is still warm. The warm oil leaks out easily and
can remove the precipitates.
6.2 MAMULÜN UZUN SÜRE KULLANILMAMASI
Toprak frezesi uzun süre (bir ay veya daha uzun) çalýþtýrýlmamasý halinde aþaðýdaki önlemlerin alýnmasý önemle
tavsiye edilir.
1.Toprak frezesini özenle yýkayýp temizleyiniz.
2.Traktörün gövdesini kontrol ediniz. Gerekirse paslanmayý önlemek için boyasýný yenileyiniz.
3.Bütün cývatalarý kontrol ederek sýkýnýz.
4.Genel bir yaðlama yapýnýz.
5.Vites kutusundaki yað seviyesini kontrol ediniz. Gerekirse yað ilave ediniz.
6.Motor tanýtma ve kullanma kýlavuzunda belirtildiði þekilde motoru koruyunuz.
7.Tek akslý traktörü iyi havalandýrýlmýþ ve kuru bir yerde park ediniz.
8.Mümkünse tek akslý traktörü kaldýrýp destekler üzerine oturtunuz. Bu durumda lastiklerdeki hava basýncý yarýya
indirilmelidir.Eðer tek akslý traktörün kaldýrýlarak desteðe alýnmasý mümkün deðilse lastiklere tavsiye edilen basýnçta
hava basýnýz ve aracý zaman zaman hareket ettiriniz. Böylece lastiklerin yere basan yüzeyleri deðiþecektir.
9.Toprak frezesini bir koruyucu örtü ile örtünüz. Su geçirmeyen örtü (plastik veya muþamba gibi) kullanmayýnýz.
Bunlar nemi tutarak paslanmaya sebep olurlar.
6.2- NON-USAGE OF THE PRODUCT FOR A LONG PERIOD OF TIME
It is recommended that the following measures are taken in the case that the motor-hoe is not used for a long period of
time.
1.Clean the motor-hoe by washing it thoroughly.
2.Check the body of the motor-hoe. If needed renew its paint to prevent corrosion.
3.Tighten all the bolts.
4.Make an overall lubrication.
5.Check the oil level in the gearbox. Add oil if needed.
6.Protect the engine as explained in the engine manual.
7.Park the motor-hoe in a place, which is well air-conditioned and dry.
8.If it is possible, lift the motor-hoe and put it on the supports. In this case the air pressure in the wheels should be
decreased by half of it. If it is not possible to lift it, increase the air pressure in the wheels to the recommended value
and move the machine occasionally. In this way the surfaces, which make contact with the ground will be changed.
9.Cover the motor-hoe with a sheet. Do not use watertight sheet (plastic or nylon). This kind of sheet keeps the
moisture and that results in corrosion.