Tascam HD-R1 Owner's Manual - 5–Screens And Menus
TASCAM HD-R1
21
5–Screens and Menus
Adjust Contrast
This permits you to adjust the screen’s contrast using
the
SHUTTLE/DATA
wheel. You may also access this
function by simultaneously pressing the
SHIFT
and
CANCEL
keys.
Playlist Defaults
Leads to a submenu containing default settings for
new playlist entries.
NOTE
Simultaneously pressing SHIFT+TIME keys is a shortcut to
the System Settings
Ducking Submenu
This menu contains all ducking-related settings:
Ducking Mode
Off
,
Attenuate Input
, or
Attenuate
Playback
. When ducking is enabled, the HD-R1
will mix the analog input with the recorder output
during playback, ducking one or the other when
a signal is present.
Attenuate Playback
will attenuate the playback volume any time there
is a signal at the analog input over the
Ducking
Threshold
.
Attenuate Input
will
attenuate the input volume any time there is a
playback signal over the
Ducking Threshold
.
Ducking Threshold
-6 dBFS
,
-12 dBFS
,
-18 dBFS
,
-24
dBFS
,
-30 dBFS
Ducking Attenuation
-3 dB
,
-6 dB
,
-9 dB
,
-12 dB
,
-18 dB
,
-24 dB
,
-Infinity
. Determines the amount of
attenuation used when ducking.
Ducking Hold Time
0.1 sec, 0.5 sec, 1.0 sec, 1.5
sec, 2.0 sec, 2.5 sec, 3.0 sec,
3.5 sec, 4.0 sec, 4.5 sec, 5.0
sec
. The ducking control signal must remain below
the
Ducking Threshold
for this many
seconds for the HD-R1 to stop attenuating.
Metering Submenu
This menu contains all meter-related settings.
Meter Clip Hold
Flash
,
3 sec
,
6 sec
,
10 sec
or
Infinite
.
When set to
Infinite
, the overload indicator on
the display is cleared by pressing
CANCEL
.
Meter Decay Rate
Fast Decay
,
Medium Decay
or
Slow
Decay
. Determines how quickly the meter decays.
Meter Peak Decay
Hold
,
Fast Decay
,
Medium Decay
,
Slow
Decay
or
Off
. Determines how quickly the peak
decays.
Meter Overload Threshold
-0.2 dBFS
or
0 dBFS
. Signals over this
threshold cause the overload indicator to come on.
Network Submenu
This menu contains all settings that pertain to the
LAN Ethernet port.
Change Password
The password is used to limit access via the LAN. The
password can be from 0 to 8 characters. By factory
default, the password is
hdr1
.
IP Address
T
he
IP Address
set up is displayed.
IP Mode
DHCP
or
Static
. When set to
DHCP
, the
IP
Address
,
IP Mask
, and
Gateway
are
obtained automatically, provided that there is a DHCP
server on the LAN. When set to
Static
, they must
be set manually.
DHCP
is the default.
IP Address
When in
Static
mode, this is used to set the IP
Address. When in DHCP mode, the
IP Address
is obtained automatically, so it is simply displayed
here and cannot be modified.
IP Mask
When in
Static
mode, this is used to set the
IP Mask
. When in DHCP mode, the
IP Mask
is
obtained automatically, so it is simply displayed here
and cannot be modified.
Gateway
When in
Static
mode, this is used to set the
Gateway
. When in DHCP mode, the
Gateway
is
obtained automatically, so it is simply displayed here
and cannot be modified.