Triple S 20C Operating Instructions Manual

Manual is about: AUTOMATIC SCRUBBER

Summary of 20C

  • Page 1

    Read this book operating & maintenance introduction instructions automatic scrubber model 20c this operator’s book has important information for the use and safe operation of this machine. Read this book care- fully before starting the machine. Keep this book and tell all operators to read the book....

  • Page 2

    Table of contents 2 important safety instructions symbols used on the machine machine preparation 1. Unpacking the machine 2. Battery installation 3. Connecting the battery charger 4. Charging the batteries 5. Connecting the battery connector 6. Battery charge level indicator 7. Squeegee assembly 8....

  • Page 3

    Read and understand all instructions and warnings before operating this machine! Warning: to reduce the risk of fire, electric shock or injury: 1. You must have training in the operation of the machine before using it. Read the instruction book. If you do not understand any instruction, ask your sup...

  • Page 4

    4 symbols used on the machine symbol for the water lever: indicates the valve is open. Symbol for the brush : indicates the brush motor switch. Symbol for the vacuum motor : indicates the vacuum motor switch. Symbol indicating the raised or lowered position of the squeegee : indicates the squeegee l...

  • Page 5

    5.

  • Page 6

    2 1 6 machine preparation 1. Unpacking the machine 1. Use a fork truck to move the machine when packaged. 2. Take off the outer package 3. The machine is fixed on the pallet with wooden wedges that block the wheels. 4. Take the wedges off. 5. Using a ramp, pull the machine down from the pallet, push...

  • Page 7

    2 2 1 7 machine preparation 5. Place the batteries in their compartment. 6. Connect the batteries’ connector (2) to the machine’s connector (1). 7. Reassemble the recovery tank, vacuum plug and squeegee hose. 3. Connecting the battery charger the battery chargers’ connector fits into the battery con...

  • Page 8

    1 8 machine preparation 5. Connecting the battery connector after charging the batteries, reconnect the battery connector (2) to the connector of the machine (1). 6. Battery charge level indicator the batteries’ indicator is digital with 4 fixed positions and a blinking one. The numbers, which appea...

  • Page 9

    5mm 9 machine preparation 9. Adjusting the squeegee inclination during operation, the rear squeegee blade is most efficient when tilted back about 3/16 inch (5mm) along its whole length. To increase the blade bending in the central part, tilt the squeegee body backward by turning the adjuster counte...

  • Page 10

    10 machine preparation 12. Recovery tank open the lid and confirm the following connections are secure: 1. The vacuum plug (2) is securely attached, turn clockwise to tighten. 2. The vacuum hose (1) is attached. 3. The plug on the drain hose (on the back of the machine) is inserted. 13. Solution wat...

  • Page 11

    1 3 2 11 operation operating 1. Connect the machine connector (1) to the battery connector. 2. Press the brush motor switch (2). 3. Press the vacuum motor switch (3). 4. Adjust the amount of cleaning solution through the lever (4). There should be enough solution to wet the floor uniformly, but not ...

  • Page 12

    12 operation device too full the machine is equipped with a float that stops the vacuum when the recovery tank is full. When this occurs, empty the recovery tank by removing the plug on the drain hose. Warning! Use gloves for protection from contact with dangerous solutions. Movement the movement of...

  • Page 13

    13 upon completion of the work after finishing your work and before any type of maintenance is done, it is necessary to do the following: 1. Close the water valve through lever (1). 2. Raise the brush base with the pedal. 3. Lift the squeegee with lever (2). Note: the squeegee blades can be damaged ...

  • Page 14

    14 daily maintenance cleaning the recovery tank 1. Empty the recovery tank by removing the drain plug from the drain hose. Warning! Use gloves for protection from contact with dangerous solutions. 2. Lift the cover of the recovery tank. 3. Take off the vacuum plug (1) by rotating it counter-clockwis...

  • Page 15

    15 daily maintenance replacing the squeegee blades check the squeegee blades for wear and if necessary, change them. To replace the squeegee blades: 1. Remove the squeegee hose from its coupling. 2. Take off the pin from the stud bolt. 3. Remove the squeegee from its support. 4. Loosen the wing nuts...

  • Page 16

    16 weekly maintenance cleaning the squeegee hose weekly or whenever the suction is insufficient, make sure the squeegee hose is not obstructed. To clean: 1. Take off the hose from its coupling on the squeegee. 2. Take off the other end from the recovery tank. 3. Wash the inner part of the hose with ...

  • Page 17

    17 trouble shooting guide insufficient water onto the brush 1. Make sure the water valve is open (lever 1). 2. Confirm there is water in the solution tank. The machine does not clean satisfactorily check the condition of the brush and replace it if necessary. The brush should be replaced when the br...

  • Page 18

    Sss automatic scrubber, model 20c limited warranty the sss automatic scrubber, model 20c has been manufactured, tested and inspected in accordance with specific engineering requirements, and is warranted by the manufacturer to be free from defects in workmanship and materials. This warranty is, howev...