Vacon nx ac drives dc/dc converter operating guide ®.
Vacon • 1 local contacts: http://drives.Danfoss.Com/danfoss-drives/local-contacts/ table of contents document id:dpd01901a revision release date: 01.11.2016 1. Introduction ................................................................................................................ 2 1.1 applicat...
1 vacon • 2 introduction local contacts: http://drives.Danfoss.Com/danfoss-drives/local-contacts/ 1. I ntroduction the dc/dc application creates output according to the needs of the system, and it is possible to integrate into the system with different topologies. Choosing applicable topology, see t...
Introduction vacon • 3 local contacts: http://drives.Danfoss.Com/danfoss-drives/local-contacts/ 1 figure 2. Fr4-fr9 main terminals fr6 u v w l1 l2 l3 fr4 fr5 b- r- b+ r+ u v w b- r- b+ r+ l1 l2 l3 fr7 r- b+/r+ b- fr8 b- b+/r+ r- fr9 l2 l1 l3 u/t1 v/t2 w/t3 l1 l2 l3 l1 l2 l3 u v w u v w u v w b- r- b...
1 vacon • 4 introduction local contacts: http://drives.Danfoss.Com/danfoss-drives/local-contacts/ figure 3. Ch62 main terminals dc+ dc- w v u.
Introduction vacon • 5 local contacts: http://drives.Danfoss.Com/danfoss-drives/local-contacts/ 1 figure 4. Fi4-fi10 basic wiring diagrams note: the location and selection of fuses varies according to system design. + - + - nxp control x10 fi 9/10 b+ dc+ dc- b- x15 x9 h1..H7 pe fi4-fi8 fi9-fi10 b+ b...
1 vacon • 6 introduction local contacts: http://drives.Danfoss.Com/danfoss-drives/local-contacts/ figure 5. 2 x fi10 basic wiring diagram note: the location and selection of fuses varies according to system design. X15 x9 x10 h1-h7 x15 x9 x10 h1-h7 + - nxp control b+ dc+ dc- b- fi10 module 1 fi10 mo...
Parameters vacon • 7 24-hour support +358 (0)201 212 575 • email: service@vacon.Com 2 2. P arameters 2.1 source side parameters 2.1.1 basic parameters p2.1.1 s ource n om c urrent id113 this parameter defines the current value that is used as the 100 % current for e.G. Charging current limit. P2.1.2...
2 vacon • 8 parameters tel. +358 (0) 201 2121 • fax +358 (0)201 212 285 2.1.2 voltage reference p2.2.1.1 dc v oltage r eference id1462 voltage reference in percentage of source nom voltage. P2.2.1.2 d rooping id620 voltage reference drooping. Used when parallel dc-dc converters are used. P2.2.1.3 r ...
Parameters vacon • 9 24-hour support +358 (0)201 212 575 • email: service@vacon.Com 2 2.1.3 current reference p2.2.2.1 c urrent reference id1860 the active current reference of the drive in percentage of source nominal current. Active curr. Ref > 0: current flow from drive dc-link to source. Active ...
2 vacon • 10 parameters tel. +358 (0) 201 2121 • fax +358 (0)201 212 285 2.1.4 source voltage p2.5.4.1 s ource min voltage id1893 if source dc voltage reaches this minimum value, discharging is disabled. P2.5.4.2 s ource max voltage id1895 if source dc voltage reaches this maximum value, charging is...
Parameters vacon • 11 24-hour support +358 (0)201 212 575 • email: service@vacon.Com 2 2.2 dc-link side parameters 2.2.1 over voltage control for dc-link voltage p2.5.3.1 o ver voltage reference id1528 the over voltage reference in percentage of nominal dc voltage of the drive. P2.5.3.2 o ver voltag...
3 vacon • 12 control io tel. +358 (0) 201 2121 • fax +358 (0)201 212 285 3. C ontrol io table 8. Default i/o configuration k1 nxopta1 nxopta2 terminal signal description 1 +10 vref reference voltege output 2 ai1+ analogue input 1. Range 0-10v, r i = 200 Ω range 0-20 ma, r i = 250 Ω analogue input 2....
Document id: *dpd01901a* dpd01901a rev. A sales code: doc-insdcdc+dluk vacon ltd member of the danfoss group runsorintie 7 65380 vaasa finland www.Danfoss.Com.
