VADDIO WALLVIEW CCU HE100 Installation And User Manual - page 7
WallVIEW CCU HE100
Quick-Connect CCU HE100 Installation and User Guide 341-789 Rev. B Page 7 of 12
Setting the Format and Output Settings (continued):
NOTE: Only values that are valid for the specific camera firmware will be saved. Confirmation of the format
or output saved can be verified by turning the Pedestal or Chroma knobs.
Exiting Camera Setup Mode: Exiting this configuration mode is done by pressing either the AWB or OPWB
button on the Quick-Connect CCU. “Exit Setup” is displayed on the LCD screen when either button is
pressed.
All of the cameras Format and Output settings can be accessed with the Panasonic IR Remote Control.
Connecting the Tally Port (optional)
The CCU system is capable of illuminating a Tally light on the front of the Quick-Connect enclosure. This
light provides a visual indicator to the equipment operator to know which camera is live during a broadcast.
In addition the tally function will illuminate the tally light on the front of the camera lens, to allow the presenter
to know which camera is live.
General Specifications
WallVIEW CCU HE100
Part Numbers
WallVIEW
CCU HE100 999-6107-000 (NTSC)
WallVIEW
CCU HE100 999-6107-001 (PAL)
•
Panasonic AW-HE100
Image Device
1/3” CCDs x 3
Signal System
N: 1080/59.94i, 720/59.94p, 480i,
P: 1080/50i, 720/50p, 576i
Lens
13x Optical Zoom
Focal Length
f=4.2 to 55mm
Horizontal Viewing Angle
5.1 to 60 degrees (16:9); 3.8 to 47 degrees (4:3)
Pan/Tilt Angle
-175 to +175 degrees (Pan), -40 to +210 degrees (Tilt)
•
Quick-Connect CCU Interface (QCCU)
Connectors
Power Connector: 5.5mm OD x 2.5mm ID
Power RJ-45: Supplies 36V to EZCamera Interface Module Regulator
Control In RJ-45: Accepts RS-232 from ProductionVIEW or other non-daisy-chain control systems
Control Out RJ-45: Passes RS-232 and Sync video feed to camera EZIM
Tally: 2-Pin Phoenix type spring cage connector
G/L Input: BNC Connector for Sync
Video Outputs: BNC Connectors for HD Analog Component (Y,PB,PR) / SD (Composite)
Video RJ-45: Transports HD video from camera EZIM
Camera Select Switch
Dip Switch 2 UP for WallVIEW CCU HE100 (the rest remain down)
Video Adjustments
Y-Gain (luminance gain) for fine tuning over longer cable distances
Distance Compensation: 100’, 200’, 300’, 400’+
CAT-5 Cable Distance
Up to 500’ (152.4m)
Power Supply
36 VDC, 2.78 Amp
Dimensions
1-RU Rack Mount - 1.75” H x 19” W x 6” D (4.45 cm x 4.26 cm x 15.24 cm)
•
EZCamera Interface Module CCU (EZIM)
Connectors
Three (3) RJ-45 Connectors
One DB-25 for Power, Video, Control & Genlock
EZIM CCU Cable
Assembly
For Panasonic HE100 Camera: DB-25M to DB-15HD, DB-9 to RJ-45, BNC x 2, 4-Pin XLR-F Power
Connector PN# 440-6707-110
Power Regulator
Supplies 12VDC to Cameras
Dimensions
3” H x 4.5” W x 1.2” D (7.6 cm x 11.4 cm x 3 cm)
•
Thin Profile Wall Mount HE100
Materials
12-Gauge CRS with Black Powder Coat Paint
Dimensions
8” H x 8.5” W x 13.5” D (20.3 cm x 21.6 cm x 34.3 cm)
Weight
Approx. 6 lbs. (2.7kg)