- DL manuals
- Vais Technology
- Network Card
- SL3x
- Owner's Manual
Vais Technology SL3x Owner's Manual
Summary of SL3x
Page 1
Audio interface controller with built-in xm satellite radio interface www.Vaistech.Com owner’s manual copyright (c) 2003-2012 vais technology published august 7, 2012 toyota • lexus • scion ( required xm direct cnp2000uca ).
Page 2
Do not disassemble or alter doing so may result in an accident, fire or electric shock do not block your view do not mount product or any added audio and/or video equipment where it can block your view through the windshield or your view of dashboard indicators and displays. Do not block the airbag ...
Page 3
Before you start this unit is equipped with: ! Built-in electronic ground noise isolator to eliminate unwanted car engine noise. ! Resettable fuses (provides protection for electronic circuits from over-current conditions) this unit is a interface adapter for toyota/lexus head unit to control xm n t...
Page 4
Connections 4 connecting the units vehicle antenna xm direct cnp2000uca soundlinq3 20-pin y- harness soundlinq3 audio harness (36”) soundlinq3 12-pin y- harness soundlinq3 interface adapter model sl3x mode programming switch power and audio wiring harness service port red led interface connector for...
Page 5
Connections 5 head unit (radio receiver) factory audio harness soundlinq3 20-pin y- harness plug into head unit (connector “a”) a a to soundlinq3 connection diagram used for all 2001-2009 lexus vehicles connecting soundlinq3 to head unit using 20-pin y-harness head unit (radio receiver) connection d...
Page 6
Installation we strongly recommend that you install the unit in an easily accessible location, so you can later upgrade the unit or re-program it in case of incorrect programming. Important @ gain access to the back of your vehicle’s head unit. @ find the same port as our y-harness (see “connecting ...
Page 7
Installation 7 emulation mode selection (sat emulation) sat emulation mode programming steps: @ properly install this unit. @ put “left” programming switch in “down” position. @ put ignition switch into the “acc” position. @ wait for long beep followed by a few short beeps. This may take up to one m...
Page 8
Cd changer or md changer emulation sat emulation 8 emulation.
Page 9
Audio input dedicated for xm radio receiver can only be used for integration. Control of xm radio receiver this unit supports the direct tuner . (model # cnp2000uca) xm radio is done through your head unit or the steering wheel controls (explained below). Xm this unit can be programmed in cd changer...
Page 10
Xm radio controls you must set the correct display mode, in order to display channel number and text information correctly. ( see “xm radio input settings” for details). Track+ track- and select next/previous channel (if the selected channel is not available, the unit will jump to the next available...
Page 11
Xm radio controls presets note: beep indicates successfully accomplished operation. If you do not hear a beep, please repeat the above steps. @ select the desired channel @ press the [rpt] or [repeat] button 4 times (must be done within 1-2 seconds). You will hear a beep. @ soundlinq3 will store the...
Page 12
Xm radio controls display settings soundlinq3 supports 8 types of display modes. Display mode can only be set up for the xm radio source. It is critical to setup, the correct display mode for the following reasons: ! For channel information to be displayed correctly. ! For text information to be dis...
Page 13
Xm radio controls display settings track number, minutes , and secondsare used to display the selected satellite channel number. Note: for cars with the radio integrated into the navigation system, “disc” number must be “invisible” or “12” in order to have all ten numbers availablefor “direct entry”...
Page 14: Sat Emulation
Audio input dedicated for xm radio receiver can only be used for integration. Control of xm radio receiver this unit supports the direct tuner (model # cnp2000uca) xm radio is done through your head unit or the steering wheel controls (explained below). Xm please see attached chart to determine whic...
Page 15
Head unit controls 15 select desired source by pressing the am button on the head unit or mode on the steering wheel control. (see diagram below) head unit: to switch between unit sources, press the am button on the head unit. The am button will cycle through the following modes: am radio, sat1, sat...
Page 16
Xm radio controls to display the song title and artist name that is currently playing, press the text button. If the information is available from the current satellite channel, it will be displayed. Song title and artist name can display a maximum of 16 alphanumeric characters each. Track+ track- a...
Page 17
Xm radio controls xm radio input settings you can adjust the input sound level of your satellite receiver. The sound level adjustment allows you to balance the volume control with other sources connected to your head unit (such as cd player, fm radio, etc), and eliminate possible distortions caused ...
Page 18
Channel tuning options 17 sat3 - settings mode if xm radio adds/removes a channel, you need to use [rescan] feature to update “channel list”. 1. Activate “settings mode” steps are above. 4. Push and hold "rescan" or "preset #4" on your radio to hear a short beep. 5. Unit will automatically switch to...
Page 19: Warranty
18 licensing agreement, disclaimers and limited warranty vais technology, llc license agreement for u.S.A. (hereinafter referred to as ‘product’) and its related software for most toyota/lexus vehicles 2001-2009; (hereinafter collectiv ely referred to as ‘products’). This is a legal agreement betwee...
Page 20
A copy of the ‘operational warnings and safety instructions’ is to be kept with the vehicle at all times. 3.Disclaimer and limitation of warranties . (a) except as otherwise contained herein, the products and related documentation are provided to you, “as is”. In no event shall vais be liable for an...
Page 21
5. Limited warranty. Vais warrants that the products will be free from defects in materials and workmanship for a period of one (1) year from the date of purchase. Vais’s sole obligation under this warranty is to repair or replace at vais's option, any products that vais shall have determined to be ...
Page 22: The Vais Products.
6. Other provisions: a. Indemnification of vais, its agents and employees . By purchasing, installing and using the products, you, the end- user, agree to indemnify, defend and hold harmless, vais, and it s affiliates, directors, officers, agents and employees from an y liabilities, damage, loss, cl...