1. DL manuals
  2. Valor Fires
  3. Electric Heater
  4. 834
  5. Installer And Owner Manual

Valor Fires 834 Installer And Owner Manual - How Do I Clean My Heater?

Other manuals for 834: Installer And Owner Manual

Summary of 834

  • Page 1

    5133257/02 installer and owner guide © baxi heating u.K. Limited 2008. Model 834 electric heater fitted with one of the following fascia aldwyn, distinction 2 or panache. (gc no. Ef-032-24) this guide is intended to help you install and care for your valor fires electric heater. Please read carefull...

  • Page 2

    © baxi heating u.K. Limited 2008. All rights reserved. No part of this publication may be reproduced in any material form (including photocopying), stored in any medium by electronic means (including in any retrieval system or database) or transmitted, in any form or by any means, whether electronic...

  • Page 3: Customer Care

    Safety first. Valor fires heaters are ce approved and designed to meet the appropriate british standards and safety marks. Quality and excellence. All valor fires heaters are manufactured to the highest standards of quality and excellence and are manufactured under a bs en iso 9001 quality system ac...

  • Page 4: 1. Handling And Unpacking

    1. Handling and unpacking fascia parts may be covered in protective film. Ensure that this has been removed before using the heater. Before continuing any further with the installation of this heater please read the following: important safety instructions.  the lifting weights of the heater (kg) p...

  • Page 5: 2. Safety

    2. Safety this appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety...

  • Page 6: 3. Heater Dimensions

    Caution: in order to avoid a hazard due to inadvertent resetting of the thermal cut out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility. Important! This heater must be earthed. ...

  • Page 7: 4. Fitting The Heater

    4. Fitting the heater the installation of this heater requires a reasonable level of diy skills. Please read this guide thoroughly before commencing installation and if in doubt, seek help from a competent person. Before fitting the fuel support ensure that the back page of this guide is completed. ...

  • Page 8

    Securing the heater. The contents have been identified as in figure 2 (the fascia and fuel effect is not shown). Additional fixings may be required if fitting the heater to a plasterboard wall that has a wooden frame behind it. In such cases we recommend the use of heavy duty cavity fixings. Page 8 ...

  • Page 9

    Page 9 installer and owner guide © baxi heating u.K. Limited 2008. Panache models contents qty (illustrations are not to scale) screw (surround to plinth) 6 figure 2. Contents continued (items are not to scale) aldwyn contents qty (illustrations are not to scale) contents qty (illustrations are not ...

  • Page 10

    Fitting the heater. Distinction 2 models. 1. There is a lower support bracket supplied with the heater. Secure this to the rear base of the heater with the two screws supplied (see figure 3). 2. Decide the location of the heater. 3. The fascia is secured at the base with two knurled shoulder screws ...

  • Page 11

    Fitting the distinction 2 fascia. 1. The rear of the fascia has two vertical metal strips. The tops of these strips have a ‘u’ shape. Hang the fascia to the top side flanges of the heater using these ‘u’ channels (see figure 5). Page 11 installer and owner guide © baxi heating u.K. Limited 2008. Fig...

  • Page 12

    2. The bottom of the fascia has a bracket with two holes. Secure the bottom of the fascia to the heater using the two knurled shoulder screws supplied (see figure 6). Aldwyn model. 1. Place the wall fixing brackets as shown in figure 7. Ensure that the two fixing holes in the brackets are positioned...

  • Page 13: 5. Using The Heater

    Fitting the fuel support (all models). Before fitting the fuel support ensure that the back page of this guide is completed. 1. Locate the fuel support as in figure 8. 2. Place the coals / pebbles on top of the fuel support. It is not necessary to use all the coals / pebbles supplied. Important note...

  • Page 14: How Do I Clean My Heater?

    6. Cleaning and maintaining the heater how do i clean my heater? The heater fascia and plastic parts need only to be wiped clean with a dry soft cloth, do not use polishes or abrasive materials. I have a problem with my heater! Important safety before undertaking maintenance or replacing the lamp(s)...

  • Page 15: 1- 3.

    2. My heater is on but there is no light or heat. The first thing to do is check the wall socket. To do this plug in a known working appliance. If the appliance you have plugged in works then there is a good chance that the problem lies with the 13amp fuse in the heater plug. If either fuse or socke...

  • Page 16: 8. Warranty And Service

    8. Warranty and service information for the customer standard warranty terms & conditions the warranty is for 12 months subject to contract. In the united kingdom servicing can be carried out either by a heateam service engineer or a suitably qualified person. You must register your heater with heat...

  • Page 17

    What this warranty does not cover repairs to heaters which haven’t been installed properly and as set out in this guide. Faults caused by inadequate supply of electricity. Reimbursement of any third party repair or replacement costs that we haven’t been told about or agreed with you in advance. Comp...

  • Page 18

    Page 18 installer and owner guide © baxi heating u.K. Limited 2008..

  • Page 19

    Page 19 installer and owner guide © baxi heating u.K. Limited 2008. Brand (please tick) baxi valor wonderfire other........................ D d m m y y date of installation fascia name (block capitals) fascia code - can be found close to the information label (block capitals) model 8 3 4 serial numb...

  • Page 20

    © baxi heating u.K. Limited 2008..