Vaterra GLAMIS UNO Owner's Manual - page 12
12
ESC LED STATUS
»
No ESC LEDs will glow when there is
no throttle input from the transmitter
»
The red ESC LED glows when there is
any throttle input from the transmitter
AUDIBLE WARNING TONES
1 Input voltage: The ESC checks the in-
put voltage when it is powered ON. If a
voltage problem is detected, the ESC
continuously sounds 2 beeps with a
1 second pause (xx-xx-xx). Power OFF
the ESC and ensure the connections
are secure and that the battery power
is not too low for safe operation.
2 Radio connection: The ESC checks
radio signal input when it is powered
ON. If a problem is detected, the ESC
continuously sounds 1 beep with a 2
second pause (x--x--x). Power OFF
the ESC and ensure the radio system
is operating correctly.
NOTICE: Always disconnect the
battery from the ESC when you have
finished operating your vehicle. The
ESC’s switch only controls power
to the receiver and servos. The ESC
will continue to draw current when
connected to the battery, resulting
in possible damage to the battery
through over-discharge.
ESC CALIBRATION PROCEDURE
Ensure proper ESC function by calibrat-
ing the ESC to your transmitter inputs.
1 Power OFF the ESC.
2 Ensure your transmitter is powered
ON, the throttle is not reversed, the
throttle trim is neutral and the throttle
travel range is at 100%.
3 Press the SET button while powering
ON the ESC. Release the button as
soon as the green LED starts to flash.
4 Calibrate the throttle points by press-
ing the SET button once after each
step.
•
Neutral (1 flash)—
leave the throttle at rest,
untouched
•
Full throttle (2 flashes)—
pull the throttle fully back
•
Full brake/reverse (3 flashes)—
push the throttle fully forward
5 The motor vibrates for 3 seconds
after the last step is completed.
ESC FUNCTIONS AND MODES
The ESC includes programming options
so you can adjust the way your vehicle
performs. Refer to the included settings
table to adjust the ESC for your driving
conditions.
ESC PROGRAMMING
PROCEDURE
Programming is accomplished using the
SET button on the ON/OFF switch.
PROGRAMMING THE ESC:
1 Connect a fully charged battery
to the ESC.
2 Power ON the ESC.
3 Hold the SET button for 1 second
until the green LED blinks, then
release the SET button to enter
programming mode.
4 Press and release the SET button as
needed to get to the desired menu
option (the Green LED will blink
corresponding to the menu
item number).
5 When at the desired menu item, hold
the SET button for 3 seconds until the
red LED blinks.
6 Press the SET button to move among
the settings based on how many
times the red LED blinks (Refer to the
table for more information).
7 Save the setting by holding the SET
button for 3 seconds.
8 Power OFF the ESC and repeat the
instructions above to change other
settings.
Tip: If desired, the ESC programming
can be returned to default settings
by powering ON the ESC and holding
the SET button for 5 seconds.
TECHNICAL
SPECIFICATIONS
Type Sensorless/
Waterproof
Constant/Peak 70A/290A
Resistance
0.0012 Ohm
Function
Forward Only with
Brake
Forward/Reverse
with Brake
Operation
Proportional forward,
proportional reverse
with braking delay
Battery Type/
Input Voltage 2–3 cell Li-Po/Li-Fe or
4–9 cell Ni-MH/Ni-Cd
BEC output 6V/3A
Overload
Protection Thermal
Dimensions
(LxWxH)
31.5mm x 27.5mm x
33mm (1.24 in x 1.08 in
x 1.30 in)
Weight
74 g (2.61 oz)
with wires
DYNAMITE 70A WATERPROOF SENSORLESS BRUSHLESS ESC
/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /