1. DL manuals
  2. VDO Cyclecomputing
  3. Bicycle Accessories
  4. x3dw
  5. Instruction Manual

VDO Cyclecomputing x3dw Instruction Manual

Other manuals for x3dw: Instruction Manual
Manual is about: Series X

Summary of x3dw

  • Page 1

    I f gb d 1 x3dw d bedienungsanleitung gb instruction manual f manuel d‘ installation et d‘ utilisation i manuale d‘ installazione e funzionamento se r ie s- x i f gb d.

  • Page 2: Preface

    X3dw vdo cyclecomputing 30 f i d gb preface congratulations with your selection of a vdo computer you have opted for a technically very high quality appliance. In order to fully benefit from the potential of the computer, we recommend that you carefully read this manual. It contains all operating in...

  • Page 3: Table of Contents

    I f www.Vdocyclecomputing.Com x3dw 31 d gb table of contents 1. Display 32 2. Operation 34 3. Functions 35 3.1 information functions 35 in function mode 3.2 timer-functions 36 3.3 cadence option 37 4. Installation 37 4.1 fitting the transmitter, magnet 37 and handlebar holder 4.2 switching on the co...

  • Page 4: 1.  Display

    X3dw vdo cyclecomputing 32 f i d gb 1. Display the display can be divided into 5 sections: section 1 always shows the current time. Section 2 shows the current cadence, if the cadence transmitter is installed (optional). Section 3 shows the current speed. Section 4 shows the value of the display fun...

  • Page 5

    I f www.Vdocyclecomputing.Com x3dw 33 d gb service indicator shows that your bike should go for a service. You can set the service interval individually for bike 1 and bike 2 stopwatch indicator shows that a timer is still running whilst you have retrieved other information on the display indicator ...

  • Page 6: 2.  Operation

    X3dw vdo cyclecomputing 34 f i d gb c = clear in function mode: b jump back a menu level from the submenu. B hold c for 3 seconds: set timer back to zero. In setting mode: b jump back to function mode. B correct an entry. B jump back a digit. = down in function mode: b scroll downwards within the fu...

  • Page 7: 3.  Functions

    I f www.Vdocyclecomputing.Com x3dw 35 d gb 3. Functions 3.1 information functions in function mode tripdistance shows the distance of the current trip since the last reset.Maximum value 999.99 km. If the maximum value is exceeded, the counter starts again at zero. At the same time the values for rid...

  • Page 8: 3.2  Timer-Functions

    X3dw vdo cyclecomputing 36 f i d gb 3.2 timer-functions the x3dw has 7 different selectable timers. Only the timer selected is shown on the display. Stopwatch you can use the stopwatch to measure as ma- ny times as you want. Maximum value: 23:59:59 hh:mm:ss. If the maximum value is exceeded, the cou...

  • Page 9: 3.3  Cadence Option

    I f www.Vdocyclecomputing.Com x3dw 37 d gb 3.3 cadence option the cadence menu is only available if b the cadence transmitter is installed, b the transmitter was recognized during pairing. After pairing the cadence transmitter, the current ca- dence is shown in section 2 of the display. In function ...

  • Page 10: >>> P05

    X3dw vdo cyclecomputing 38 d gb to wake it up out of despatch mode, press the button simultaneously for a few seconds. The computer is now ready for use and tells you so by showing the language setting. See also chapter 4.4 4.2 switching on the computer for the first time >>> p02, display see chapte...

  • Page 11: >>> P06

    Www.Vdocyclecomputing.Com x3dw 39 i f d gb 4.4 language setting after battery change after inserting the battery, your vdo computer automatically welcomes you in the english main menu. Language english. Confirm with m . English select ok? Confirm with m . Computer confirms: language select done. Aut...

  • Page 12: 4.6  Transmitter Pairing

    X3dw vdo cyclecomputing 40 f i d gb 4.6 transmitter pairing the speed and cadence signals (option: item no. 7702) will be transmitted digitally and encoded to your computer. This technology is less prone to problems than analogue transmission. This way, when riding in a group there are no data overl...

  • Page 13

    I f www.Vdocyclecomputing.Com x3dw 41 d gb 5.2 setting and measuring the wheel size 5.2.1 setting using tyre table you must set the wheel size (wheel roll circum- ference) of your bike so that your vdo computer can measure correctly. There are 2 ways of doing this: the common types of tyres are list...

  • Page 14: >>> P07

    X3dw vdo cyclecomputing 42 f i d gb how to set the tyre size by selecting the tyre: using go to settings/ select. Confirm with m . You are now in setting mode (pressing c for 3 seconds gets you back to function mode). Using up/down go to wheelsize/set. Confirm with m . Measurement/kmh. Confirm with ...

  • Page 15

    I f www.Vdocyclecomputing.Com x3dw 43 d gb wheelsize/bike 1. (use to go to setting for bike 2) confirm with m . Using go to wheel-size/manual set. Confirm with m . Bike 1 ...Set size/continue now set the wheel roll circum- ference measured using . Confirm the entry with m . Bike 1/set ok? Confirm wi...

  • Page 16

    X3dw vdo cyclecomputing 44 f i d gb the display confirms: clock/set done. Automatic return to settings/select. How to set the alarm: using go to settings/ select. Confirm with m . You are now in setting mode (pressing c for 3 seconds gets you back to function mode). Using go to clock/alarm/ set. Con...

  • Page 17

    Www.Vdocyclecomputing.Com x3dw 45 d gb f i alarm/set ok? Confirm with m . The display confirms: alarm/set done. Automatic return to settings/select. If you have set the alarm to on, the alarm symbol appears on the bottom left of the display -symbol. Alarm...Set hour/continue set the hours using up/d...

  • Page 18: >>> P03

    X3dw vdo cyclecomputing 46 f i d gb 5.5 switch from bike1 to bike2 >>> p03 5.6 service interval display the selected bike 1 or 2 is shown on the display bottom left ( ). Note: the transmitter on bike 2 must have been set to bike 2 before using it the first time. >>> p03 how to set the service interv...

  • Page 19: 5.7  The Navigator

    I f www.Vdocyclecomputing.Com x3dw 47 d gb bike service/bike 1 (use to switch to bike 2) confirm with m . Bike 1 ...Set distance/ continue. You can set the flash- ing digits using to access the next digit, confirm with m . Repeat the steps until the last digit on the right is flashing. Confirm with ...

  • Page 20: 5.8  Sleep Mode

    X3dw vdo cyclecomputing 48 f i gb in sleep-modus 2 the wireless receiver is also switched off. (after 15 min). The display shows sleep mode/press button before continuing to ride, you must press a button to switch the receiver back on. The display for the speed and the cadence flashes. Navigator/set...

  • Page 21: 5.9  Reset Functions

    I f www.Vdocyclecomputing.Com x3dw 49 d gb using go to data reset/ select. Confirm with m . Use to go to the data you want to reset: b data reset/tour data b data reset/tot ride tm b data reset/odo total b data reset/lap data b data reset/navigator confirm your selection with m . Query: selected dat...

  • Page 22: 6.  Timer Functions

    X3dw vdo cyclecomputing 50 d gb f i 5. Countdown you can program a time, and the timer counts back- wards from this time. At the end of the countdown time a single beep is heard. 6. Time trial on the time trial timer, a distance can be set (time trial distance). Whilst cycling, the expected ride tim...

  • Page 23: 6.1  Selecting Timers

    I f www.Vdocyclecomputing.Com x3dw 51 d gb 6.1 selecting timers when confirming the select the timing function last selected always appears. Confirm with m . Timer/select ok? Confirm with m . Timer/select done appears briefly and your vdo computer automatically returns to the start menu settings/ se...

  • Page 24

    X3dw vdo cyclecomputing 52 f i d timer1+2…set repeats/ continue. Using enter the number of repeats you want (e.G. In interval training). Confirm with m . Timer1+2/set ok? Confirm with m . Return confirmation: timer1+2/set done your vdo computer automatically returns to the menu settings/select. Sett...

  • Page 25

    I f www.Vdocyclecomputing.Com x3dw 53 gb d lap timer/manual start (use to switch lap timer/ auto start. Confirm with m . If you have chosen auto start, you must now enter the distance, after which the next lap is automatically started (e.G. 1 km) lap timer… set distance/ continue the flashing digit ...

  • Page 26: 6.3  Operating The Timers

    X3dw vdo cyclecomputing 54 f i d gb 6.3 operating the timers recalling lap data: using go to settings/ select. Confirm with m . You are now in setting mode (pressing c for 3 seconds gets you back to function mode). Using go to lap data/ recall. Confirm with m . Lap data/lap 1. Using you can selected...

  • Page 27: 7.  Terms of Guarantee

    I f www.Vdocyclecomputing.Com x3dw 55 d gb 7. Terms of guarantee please contact the dealer from whom you purchased the device for all complaints and guarantee claims. Or send your complaint directly to: cycle parts gmbh große ahlmühle 33 d-76865 rohrbach (germany) we would be pleased to answer any t...

  • Page 28: 8.  Troubleshooting

    X3dw vdo cyclecomputing 56 f i gb d 8. Troubleshooting here you can find a list of possible faults, their causes and what you can do about them: error possible cause correction half segments on the display (e.G. After a battery change) computer software not running correctly after battery change tak...

  • Page 29

    I f gb d www.Vdocyclecomputing.Com x3dw 57 gb d 9. Technical spezifications speed range: for wheel size 2155 mm, min 2.5 km/h, max 199.5 km/h ride time measurement range: up to 23:59:59 hh:mm:ss stopwatch measurement range up to 23:59:59 hh:mm:ss day‘s trip counter measurement range: up to 999.99 km...

  • Page 30

    116 d gb f i se r ie s- x www.Cyclecomputing.Com cp-x3dw-bda 1 / 1.

  • Page 31

    Fcc id: tfo7702 fcc compliance and advisory statement this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that ma...