1. DL manuals
  2. Vega
  3. Switch
  4. VEGAWAVE 63
  5. Operating Instructions Manual

Vega VEGAWAVE 63 Operating Instructions Manual

Manual is about: NAMUR

Summary of VEGAWAVE 63

  • Page 1

    Operating instructions vegawave 63 - transistor (npn/pnp) document id: 32258 vibration.

  • Page 2: Contents

    Contents 1 about this document 1.1 function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.2 target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.3 symbolism used. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 for your safety 2.1 authorised...

  • Page 3

    9 supplement 9.1 technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 9.2 dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 supplementary documentation information: supplementary documents appropriate to the ordered version come with the delivery. You...

  • Page 4: About This Document

    1 about this document 1 .1 function this operating instructions manual provides all the information you need for mounting, connection and setup as well as important instructions for maintenance and fault rectification. Please read this information before putting the instrument into operation and keep...

  • Page 5: For Your Safety

    2 for your safety 2 .1 authorised personnel all operations described in this operating instructions manual must be carried out only by trained specialist personnel authorised by the plant operator. During work on and with the device the required personal protective equipment must always be worn. 2 ....

  • Page 6

    2 .5 safety label on the instrument the safety approval markings and safety tips on the device must be observed. 2 .6 ce conformity this device fulfills the legal requirements of the applicable ec guidelines. By attaching the ce mark, vega provides a confirmation of successful testing. You can find the...

  • Page 7: Product Description

    3 product description 3 .1 structure the scope of delivery encompasses: l vegawave 63 point level switch l documentation - this operating instructions manual - safety manual "functional safety (sil)" (optional) - supplementary instructions manual "plug connector for level sensors" (optional) - ex-sp...

  • Page 8

    L sil identification (with sil rating ex works) with the serial number, you can access the delivery data of the instrument via www.Vega.Com, "vega tools" and "serial number search". In addition to the type label outside, you can also find the serial number on the inside of the instrument. 3 .2 princip...

  • Page 9

    3 .3 operation with the factory setting, products with a density of > 0.02 g/cm³ (0.0008 lbs/in³) can be measured. The instrument can also be adapted to products with lower density > 0.008 g/cm³ (0.0003 lbs/in³). On the electronics module you will find the following indicating and adjustment elements...

  • Page 10: Mounting

    4 mounting 4 .1 general instructions make sure that all parts of the instrument exposed to the process, in particular the sensor element, process seal and process fitting, are suitable for the existing process conditions. These include above all the process pressure, process temperature as well as th...

  • Page 11

    The max. Permissible pressure is specified in chapter "technical data" or on the type label of the sensor. The vibrating level switch is a measuring instrument and must be treated accordingly. Bending the vibrating element will destroy the instrument. Warning: the housing must not be used to screw th...

  • Page 12

    Fig. 3: inflowing medium vegawave 63 can be mounted with a lock fitting for height adjustment. Take note of the pressure information of the lock fitting. The vibrating element should protrude into the vessel to avoid buildup. For that reason, avoid using mounting bosses for flanges and screwed fittings. ...

  • Page 13

    D d d 6 d 6 fig. 4: filling and emptying centred d d 6 1 2 3 fig. 5: filling in the centre, emptying laterally 1 vegawave 63 2 discharge opening 3 filling opening vegawave 63 • - transistor (npn/pnp) 13 4 mounting 32258 - en -120418.

  • Page 14

    To minimise flow resistance caused by the tuning fork, vegawave 63 should be mounted in such a way that the surfaces of the blades are parallel to the product movement. 1 2 fig. 6: flow orientation of the tuning fork 1 marking with screwed version 2 direction of flow in applications such as grit chamb...

  • Page 15

    > 125 mm (> 5") > 1 2 0 mm (> 4 .7 ") fig. 7: baffle for protection against mechanical damage vegawave 63 • - transistor (npn/pnp) 15 4 mounting 32258 - en -120418.

  • Page 16

    5 connecting to power supply 5 .1 preparing the connection always keep in mind the following safety instructions: l connect only in the complete absence of line voltage in hazardous areas you must take note of the respective regulations, conformity and type approval certificates of the sensors and po...

  • Page 17

    5 lift the opening levers of the terminals with a screwdriver (see following illustration) fig. 8: connection steps 5 and 6 6 insert the wire ends into the open terminals according to the wiring plan 7 press down the opening levers of the terminals, you will hear the terminal spring closing 8 check ...

  • Page 18

    1 4 4 4 2 3 fig. 9: material versions, single chamber housing 1 plastic (not with eex d) 2 aluminium 3 stainless steel (not with eex d) 4 filter element for pressure compensation or blind stopper with version ip 66/ ip 68, 1 bar (not with eex d) we recommend connecting vegawave 63 in such a way that...

  • Page 19

    + - + - 1 2 3 4 fig. 11: npn action + - + - 1 2 3 4 fig. 12: pnp action 5 .4 wiring plan - version ip 66/ip 68 (1 bar) 1 2 3 4 5 fig. 13: wire assignment connection cable. The numbers of the wires correspond to the terminals of the instrument. 1 brown (+) voltage supply 2 white 3 yellow 4 blue (-) v...

  • Page 20: Set Up

    6 set up 6 .1 general information the figures in brackets refer to the following illustrations. On the electronics module you will find the following indicating and adjustment elements: l potentiometer for adaptation to the product density (1) l dil switch for mode adjustment - min./max. (2) l signal ...

  • Page 21

    By default, the potentiometer of vegawave 63 is set to the right stop (> 0.02 g/cm³ or 0.0008 lbs/in³). In case of very light-weight solids, turn the potentiometer to the left stop (> 0.008 g/cm³ or 0.0003 lbs/in³). Vegawave 63 will thus be more sensitive and can detect light-weight solids more reli...

  • Page 22

    Level switching status control lamp failure of the sup- ply voltage (min./max. Mode) any open malfunction any open flashes red 22 vegawave 63 • - transistor (npn/pnp) 6 set up 32258 -en -120418.

  • Page 23

    7 maintenance and fault rectification 7 .1 maintenance if the instrument is used properly, no special maintenance is required in normal operation. 7 .2 remove interferences the operator of the system is responsible for taking suitable measures to rectify faults. Vegawave 63 offers maximum reliability....

  • Page 24

    Error cause rectification wrong mode selected set the correct mode on the mode switch (overflow protection, dry run protection). Wiring should be carried out according to the quiescent current principle. Signal lamp flashes red error on the vibrating ele- ment check if the vibrating element is damage o...

  • Page 25

    6 pull out the old electronics module 7 compare the new electronics module with the old one. The type label of the electronics module must correspond to that of the old electronics module. This applies particularly to instruments used in hazardous areas. 8 compare the settings of the two electronics...

  • Page 26: Dismounting

    8 dismounting 8 .1 dismounting steps warning: before dismounting, be aware of dangerous process conditions such as e.G. Pressure in the vessel, high temperatures, corrosive or toxic products etc. Take note of chapters "mounting" and "connecting to power supply" and carry out the listed steps in reve...

  • Page 27: Supplement

    9 supplement 9 .1 technical data general data material 316l corresponds to 1.4404 or 1.4435 materials, wetted parts - process fitting - thread 316l - process fitting - flange 316l - process seal klingersil c-4400 - tuning fork 316l - extension tube ø 43 mm (1.7 in) 316l materials, non-wetted parts - pl...

  • Page 28

    Fig. 26: max. Lateral load alongside fork side (narrow fork side) output variable output floating transistor output, permanently shortcircuit- proof load current 400 ma turn-on voltage 55 v dc blocking current 100 µa modes (switchable) min./max. Switching delay - when immersed 0.5 s - when laid bare...

  • Page 29

    1 2 3 -50°c (-58°f) 50°c (122°f) 40°c (104°f) -40°c (-40°f) 80°c (176°f) 0°c (32°f) 100°c (212°f) 150°c (302°f) 200°c (392°f) 250°c (482°f) fig. 27: ambient temperature - process temperature 1 process temperature 2 ambient temperature 3 temperature range with temperature adapter product density - st...

  • Page 30

    - tensile strength 1200 n (270 lbf) - standard length 5 m (16.4 ft) - max. Length 1000 m (3280 ft) - min. Bending radius 25 mm (0.984 in) with 25 °c (77 °f) - diameter approx. 8 mm (0.315 in) - colour - standard pe black - colour - standard pur blue - colour - ex-version blue adjustment elements mod...

  • Page 31

    9 .2 dimensions housing in protection ip 66/ip 67 and ip 66/ip 68; 0.2 bar 3 2 1 4 ~ 69 mm (2.72") ø 79 mm (3.11") 1 1 7 mm (4 .6 1 ") m20x1,5/ ½ npt ~ 59 mm (2.32") ø 80 mm (3.15") 1 1 2 mm (4 .4 1 ") m20x1,5/ ½ npt ~ 69 mm (2.72") ø 79 mm (3.03") 1 1 2 mm (4 .4 1 ") m20x1,5/ ½ npt ~ 116 mm (4.57")...

  • Page 32

    22mm ( 55 / 64 ") 33mm (1 19 / 64 ") g1½a 150mm (5 29 / 32 ") l ø 43mm (1 11 / 16 ") fig. 30: vegawave 63, threaded version g1½ a (din iso 228/1) l sensor length, see chapter "technical data" 32 vegawave 63 • - transistor (npn/pnp) 9 supplement 32258 -en -120418.

  • Page 33

    ø 34 mm (1 11 / 32 ") 1 7 8 mm (7 1 / 6 4 ") fig. 31: temperature adapter vegawave 63 • - transistor (npn/pnp) 33 9 supplement 32258 - en -120418.

  • Page 34

    9 .3 industrial property rights vega product lines are global protected by industrial property rights. Further information see http://www.Vega.Com . Only in u.S.A.: further information see patent label at the sensor housing. Vega produktfamilien sind weltweit geschützt durch gewerbliche schutzrechte...

  • Page 35

    Vegawave 63 • - transistor (npn/pnp) 35 9 supplement 32258 - en -120418.

  • Page 36

    Vega grieshaber kg am hohenstein 113 77761 schiltach germany phone +49 7836 50-0 fax +49 7836 50-201 e-mail: info.De@vega.Com www.Vega.Com printing date: iso 9001 all statements concerning scope of delivery, application, practical use and operating conditions of the sensors and processing systems co...