Iu600es series hb0133 intended for domestic cooking only installer: leave this manual with homeowner. Homeowner: use and care information on pages 10 to 12. Read and save these instructions venmar ventilation ulc, 550 lemire blvd., drummondville qc j2c 7w9 1-800-567-3855 register your product online...
2 to reduce the risk of fire, electric shock or injury to persons, observe the following: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2. Before servicing or cleaning unit,...
3 table of contents 1. I nstall ductwork .................................................................................................. 3-4 2. P repare installation ............................................................................................. 4-5 3. P repare the hood ...............
4 2. Prepare installation note: before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer. Make sure that the following items are included: - hood - installation manual - accessories: • 2 hybrid filters • 3¼” x 10” adapter/damper ...
5 3. Prepare the hood 3.1 lay the hood filters up on a table. Use a piece of cardboard to avoid damaging the table or the hood. Remove tape on filters. Lift filters by pushing them towards the back and flip them up, then set the filters aside. Hd0553 3.2 f or 30” wide hoods : remove the 7 screws ( a...
6 4.1 carefully remove glass panel from its packaging. Remove glass panel nuts (factory installed) from both studs and set aside. 4.2 insert glass panel studs in hood front holes. 4.3 while holding glass panel, pre-tighten previously removed nuts by hand. Ensure glass panel is flush with top of hood...
7 press the metal shutoff plate on a flat surface to completely flatten bent flange. Ho0245 using both screws previously removed, install the metal shutoff plate on top of the hood. Hd0415 5. Install the adapter/damper ( all models ) the wall duct must be roughed-in to properly interface with the ho...
8 6. Install the hood 6.1 run power cable to installation location. Position the hood in its intended location. Using a pen, mark the position of the screws (as shown at right). Remove the hood. 6.2 install the first four no. 8 x 1/2’’ screws, leaving a 1/8’’ gap (do not install screws nos. 5, 6 , 7...
9 8. Reinstall blower wheel and bottom panel caution when reinstalling the blower wheel, make sure the small tab is aligned with the yellow label on the motor. 8.1 reinstall blower wheel: using both hands, gently push on the blower wheel until secured. 8.2 insert bottom panel in the back of the hood...
10 11. Care h ybrid filters and bottom panel the hybrid filters and the bottom panel should be cleaned frequently. Use a warm detergent solution. Remove hybrid filters by pushing them towards the back of hood and rotating downward. Clean all-metal filters in the diswasher using a non-phophate deterg...
11 11. Care ( cont ' d ) g lass panel hot water with mild soap or glass cleaner is all that is usually needed. When using mild soap, rinse with clear water. Wipe dry with a clean, soft cloth to avoid water marks. Avoid when choosing a detergent: - any cleaners that contain bleach. They will attack s...
12 12. Operation ( cont ' d ) c. M aster on/off: when blower is off, press this button to turn the hood on to the last memorized speed level. If there is no memorized speed level, speed will be set at level 1 . To turn off the blower and the light simultaneously, press this button once. H eat s entr...
13 13. Wiring diagram warning ! Risk of electric shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power from being switched on...
14 14. Service parts hl0224 1 2 3 4 5 6 7 8 9 10 11.
15 r eplacement p arts and r epairs in order to ensure your unit remains in good working condition, you must use venmar ventilation ulc genuine replacement parts only. Venmar ventilation ulc genuine replacement parts are specially designed for each unit and are manufactured to comply with all the ap...
16 15. Warranty venmar ventilation five-year warranty venmar ventilation ulc warrants to the original consumer purchaser of the venmar ispira iu600es series range hood that such product will be free from defects in materials or workmanship for a period of five (5) years from date of original purchas...
