1. DL manuals
  2. Wacker Neuson
  3. Power Tool
  4. BS 50-2
  5. Operator's Manual

Wacker Neuson BS 50-2 Operator's Manual

Other manuals for BS 50-2: Repair Manual, Operator's Manual, Operator's Manual
Manual is about: vibratory rammer

Summary of BS 50-2

  • Page 1

    Www.Wackergroup.Com rammer bs 50-2 operator’s manual 0158433en 003 1106 0 1 5 8 4 3 3 e n.

  • Page 3: Bs 50-2

    Bs 50-2 table of contents wc_bo0158433en_003toc.Fm 1 1. Foreword 3 2. Emission control system information 4 3. Safety information 10 3.1 operating safety ................................................................................ 11 3.2 operator safety while using internal combustion engines .....

  • Page 4: Table of Contents

    Table of contents bs 50-2 wc_bo0158433en_003toc.Fm 2 6. Maintenance 26 6.1 periodic maintenance schedule ..........................................................26 6.2 servicing air cleaner ...........................................................................27 6.3 lubrication .................

  • Page 5

    Wc_tx000001gb.Fm 3 california proposition 65 warning: engine exhaust, some of its constituents, and certain vehicle components, contain or emit chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. 1. Foreword this manual provides information and pr...

  • Page 6

    Emission control system information wc_tx000030gb.Fm 4 2. Emission control system information source of emissions the combustion process produces carbon monoxide, oxides of nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions,...

  • Page 7

    Emission control system information wc_tx000030gb.Fm 5 replacement parts the emission control systems on your wacker engine were designed, built, and certified to conform with epa and california emissions regulations. We recommend the use of genuine wacker parts whenever you have maintenance done. T...

  • Page 8

    Emission control system information wc_tx000030gb.Fm 6 methanol - (methyl or wood alcohol) 5% by volume. You may use gasoline containing up to 5% methanol by volume, as long as it contains cosolvents and corrosion inhibitors to protect the fuel system. Gasoline containing more than 5% methanol by vo...

  • Page 9

    Emission control system information wc_tx000030gb.Fm 7 owner’s warranty responsibility: as the engine owner, you are responsible for the performance of the required maintenance listed in your owner’s manual. Wacker recommends that you retain all receipts covering maintenance on your engine, but wack...

  • Page 10

    Emission control system information wc_tx000030gb.Fm 8 to obtain warranty service: you must take your wacker product along with proof of original purchase date, at your expense, to any wacker authorized dealer during their normal business hours. Claims for repair or adjustment found to be caused sol...

  • Page 11

    Emission control system information wc_tx000030gb.Fm 9 systems covered by this warranty parts descriptions fuel metering carburetor assembly exhaust system muffler air induction air filter housing air filter element* ignition flywheel magneto ignition module spark plug cap spark plug* miscellaneous ...

  • Page 12: Safety Information

    Safety information bs 50-2 wc_si000119gb.Fm 10 3. Safety information this manual contains danger, warning, caution, and note callouts which must be followed to reduce the possibility of personal injury, damage to the equipment, or improper service. This is the safety alert symbol. It is used to aler...

  • Page 13: Bs 50-2

    Bs 50-2 safety information wc_si000119gb.Fm 11 3.1 operating safety familiarity and proper training are required for the safe operation of equipment. Equipment operated improperly or by untrained personnel can be dangerous. Read the operating instructions contained in both this manual and the engine...

  • Page 14: Safety Information

    Safety information bs 50-2 wc_si000119gb.Fm 12 3.1.18 always guide the rammer in such a way that the operator is not squeezed between the rammer and solid objects. Special care is required when working on uneven ground or when compacting coarse material. Make sure to stand firmly when operating the ...

  • Page 15: Bs 50-2

    Bs 50-2 safety information wc_si000119gb.Fm 13 3.3 service safety poorly maintained equipment can become a safety hazard! In order for the equipment to operate safely and properly over a long period of time, periodic maintenance and occasional repairs are necessary. 3.3.1 do not attempt to clean or ...

  • Page 16: Safety Information

    Safety information bs 50-2 wc_si000119gb.Fm 14 3.4 label locations.

  • Page 17: Bs 50-2

    Bs 50-2 safety information wc_si000119gb.Fm 15 3.5 safety labels wacker machines use international pictorial labels where needed. These labels are described below: label meaning this molded-in label contains important safety and operating information. If it becomes illegible, the cover must be repla...

  • Page 18: Safety Information

    Safety information bs 50-2 wc_si000119gb.Fm 16 caution! Use only clean, filtered gasoline fuel. Warning! To prevent hearing loss, wear hearing protection when operating this machine. Warning! Hot surface! Replace guard! Warning! Serious injury if struck by compressed spring or cover. If the spring s...

  • Page 19: Bs 50-2

    Bs 50-2 safety information wc_si000119gb.Fm 17 guaranteed sound power level in db(a) the air intake system is equipped with a filter indicator, which indicates when a filter change is required.Replace main paper filter element when yellow plunger of the indicator appears in or near the red line. A n...

  • Page 20: Safety Information

    Safety information bs 50-2 wc_si000119gb.Fm 18 3.6 operating labels wacker machines use international pictorial labels where needed. These labels are described below: label meaning close the choke. Place the throttle control lever in the “start” position. Pull the rewind starter. Open the choke. Pla...

  • Page 21: Bs 50-2

    Bs 50-2 safety information wc_si000119gb.Fm 19 throttle control lever: 0 = stop turtle = start or idle rabbit = full or fast engine stop button: press to stop engine. Choke: 0 = open l = closed this rammer engine requires a two-cycle gasoline/oil mixture. Mix regular unleaded gasoline and two-cycle/...

  • Page 22: Technical Data

    Technical data bs 50-2 wc_td000119gb.Fm 20 4. Technical data 4.1 rammer item number: bs 50-2 0009380, 0009382, 0009384, 0009410 0009411, 0009413, 0620025, 0620048 rammer engine model type wm80 engine speed - full rpm 4400 ± 100 engine speed - idle rpm 1800 ± 100 clutch engagement rpm 2500 ± 100 spar...

  • Page 23: Bs 50-2

    Bs 50-2 technical data wc_td000119gb.Fm 21 4.2 sound measurements products are tested for sound pressure level in accordance with en iso 11204. Sound power level is tested in accordance with european directive 2000/14/ec - noise emission in the environment by equipment for use outdoors. • the sound ...

  • Page 24: Operation

    Operation bs 50-2 wc_tx000312gb.Fm 22 5. Operation 5.1 application rammers are designed to compact loose soils and gravel to prevent settling and to provide a firm, solid base for the placement of footings, concrete slabs, foundations, and other structures. 5.2 recommended fuel this rammer engine re...

  • Page 25: Bs 50-2

    Bs 50-2 operation wc_tx000312gb.Fm 23 5.4 to start see graphic: wc_gr001461 5.4.1 open throttle to full position (c4). This will automatically turn on the flow of fuel. 5.4.2 close choke (b1). 5.4.3 pull starter rope (a). Repeat until engine starts. Multiple pulls (typically less than 5 pulls) may b...

  • Page 26: Operation

    Operation bs 50-2 wc_tx000312gb.Fm 24 5.5 to stop see graphic: wc_gr001461 5.5.1 place throttle in the idle position (c2). 5.5.2 shut off the engine by moving the throttle through the detent to the off position (c1). The engine will stop and the fuel valve will close. Note: if the throttle control w...

  • Page 27: Bs 50-2

    Bs 50-2 operation wc_tx000312gb.Fm 25 5.7 proper compaction see graphic: wc_gr000045 5.7.1 run rammer at the full throttle position (a4) for maximum performance. 5.7.2 guide rammer with its handle. Allow machine to pull itself forward. Do not try to over-power the machine. 5.7.3 for best compaction,...

  • Page 28: Maintenance

    Maintenance bs 50-2 wc_tx000313gb.Fm 26 6. Maintenance 6.1 periodic maintenance schedule daily before starting after first 5 hours every week or 25 hours every month or 100 hours every 3 months or 300 hours every year check fuel level. Check air filter indicator. Replace as needed. Check ramming sys...

  • Page 29: Bs 50-2

    Bs 50-2 maintenance wc_tx000313gb.Fm 27 6.2 servicing air cleaner see graphic: wc_gr001168 never use gasoline or other types of low flash point solvents for cleaning the air filter. A fire or explosion could result. Caution: never run engine without main paper filter element (b). Severe engine damag...

  • Page 30: Maintenance

    Maintenance bs 50-2 wc_tx000313gb.Fm 28 6.3 lubrication see graphic: wc_gr01463 ramming system check oil level: 6.3.1 place the rammer so it is resting on its shoe on a level surface. 6.3.2 check the oil level through oil sightglass (d). Proper ramming system lubrication is indicated when approximat...

  • Page 31: Bs 50-2

    Bs 50-2 maintenance wc_tx000313gb.Fm 29 6.4 fuel lines see graphic: wc_gr0001493 always follow instructions when disconnecting fuel lines. Failure to do so may result in fuel squirting from fuel system. To disconnect fuel lines: 6.4.1 shut off the engine by moving the throttle through the detent to ...

  • Page 32: Maintenance

    Maintenance bs 50-2 wc_tx000313gb.Fm 30 6.5 shoe hardware see graphic: wc_gr000048 on new machines, or after replacing shoe, check and tighten shoe hardware (a) after the first 5 hours of operation. Inspect hardware every week thereafter. Torque hardware as specified. 6.6 carburetor adjustments see ...

  • Page 33: Bs 50-2

    Bs 50-2 maintenance wc_tx000313gb.Fm 31 6.7 long-term storage 6.7.1 drain fuel from tank. 6.7.2 start engine and run until remaining fuel is used. 6.7.3 remove spark plug. Pour approximately 30 ml (1 oz.) of clean sae 10w30 engine oil into cylinder through spark plug opening. 6.7.4 pull starter rope...

  • Page 34: Maintenance

    Maintenance bs 50-2 wc_tx000313gb.Fm 32 6.9 troubleshooting problem / symptom reason / remedy engine does not start, or stalls. • no fuel in tank. • spark plug fouled. • fuel valve closed. Engine does not accelerate, is hard to start, or runs errati- cally. • improper fuel mix. Too much oil. • spark...

  • Page 35

    2005-ce-bs50-2-2i-q.Fm william lahner greg orzal vice president of engineering manager, product engineering wacker corporation date / datum / fecha / date ec declaration of conformity ce-konformitÄtserklÄrung declaraciÓn de conformidad de la ce dÉclaration de conformitÉ c.E. Wacker corporation, n92 ...

  • Page 36

    Wacker construction equipment ag · preußenstraße 41 · d-80809 münchen · tel.: +49-(0)89-3 54 02 - 0 · fax: +49 - (0)89-3 54 02-3 90 wacker corporation · p.O. Box 9007 · menomonee falls, wi 53052-9007 · tel. : (262) 255-0500 · fax: (262) 255-0550 · tel. : (800) 770-0957 wacker asia pacific operations...