- DL manuals
- Wacker Neuson
- Power Tool
- BS 50-2
- Operator's Manual
Wacker Neuson BS 50-2 Operator's Manual
Summary of BS 50-2
Page 1
Operator’s manual vibratory rammer bs50-2, bs50-2i bs60-2, bs60-2i bs70-2, bs70-2i bs65-v type bs50-2, bs50-2i, bs60-2, bs60-2i, bs70-2, bs70-2i, bs65-v document 5200016051 date 1116 revision 0 8 language en 5 2 0 0 0 1 6 0 5 1.
Page 2
Copyright notice © copyright 201 6 by wacker neuson production americas llc all rights, including copying and distribution rights, are reserved. This publication may be photocopied by the original purchaser of the machine. Any other type of reproduction is prohibited without express written permissi...
Page 3: Rammer
Wc_tx003550gb_fm10.Fm 3 rammer foreword foreword save these instructions—this manual contains important instructions for the machine models below. These instructions have been written expressly by wacker neuson production americas llc and must be followed during installation, operation, and maintena...
Page 4: Rammer
Wc_tx003550gb_fm10.Fm 4 rammer foreword machine identification a nameplate listing the model number, item number, revision number, and serial number is attached to this machine. The location of the nameplate is shown above. Serial number (s/n) for future reference, record the serial number in the sp...
Page 5: Rammer
Wc_tx003550gb_fm10.Fm 5 rammer foreword california proposition 65 warning combustion exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. Laws pertaining to spark arr...
Page 6: Rammer
Wc_tx003550gb_fm10.Fm 6 rammer foreword notes.
Page 7: Ec Declaration of Conformity
20 1 7-c e- bs 50 -2 _e n _f m 10 .Fm ec declaration of conformity manufacturer wacker neuson production americas llc, n92w15000 anthony avenue, menomonee falls, wisconsin 53051 usa machine: product product category product function item number net installed power measured sound power level guarante...
Page 9: Ec Declaration of Conformity
20 1 7-c e- bs 60 -2 _e n _f m 10 .Fm ec declaration of conformity manufacturer wacker neuson production americas llc, n92w15000 anthony avenue, menomonee falls, wisconsin 53051 usa product product product category product function item number net installed power measured sound power level guarantee...
Page 11: Ec Declaration of Conformity
20 1 7-c e- bs 70 -2 _e n _f m 10 .Fm ec declaration of conformity manufacturer wacker neuson production americas llc, n92w15000 anthony avenue, menomonee falls, wisconsin 53051 usa product product product category product function item number net installed power measured sound power level guarantee...
Page 13: Ec Declaration of Conformity
20 1 7-c e- bs 65 -v _ en _f m 10 .Fm ec declaration of conformity manufacturer wacker neuson production americas llc, n92w15000 anthony avenue, menomonee falls, wisconsin 53051 usa product product product category product function item number net installed power measured sound power level guarantee...
Page 15: Table of Contents
Table of contents rammer wc_bo5200016051_0 8_fm10t 15 foreword 3 ec declaration of conformity 7 1 safety information 17 1.1 signal words used in this manual ..................................................... 17 1.2 machine description and intended use ................................................
Page 16: Table of Contents
Table of contents rammer 16 5.4 checking and changing the ramming system oil .............................53 5.5 checking the fuel lines and fittings ..................................................55 5.6 maintaining the shoe hardware ..........................................................56 5....
Page 17: Rammer
Wc_si000836gb_fm10.Fm 17 rammer safety information 1 safety information 1.1 signal words used in this manual this manual contains danger, warning, caution, notice, and note signal words which must be followed to reduce the possibility of personal injury, damage to the equipment, or improper service....
Page 18: Rammer
Wc_si000836gb_fm10.Fm 18 rammer safety information 1.2 machine description and intended use this machine is a vibratory rammer. The wacker neuson rammer consists of a gasoline or diesel engine, a clutch, a fuel tank, a spring-loaded ramming system, a ramming shoe, and a handle. The engine transmits ...
Page 19: Rammer
Wc_si000836gb_fm10.Fm 19 rammer safety information 1.3 safety guidelines for operating the machine operator training before operating the machine: ■ read and understand the operating instructions contained in all manuals delivered with the machine. ■ familiarize yourself with the location and proper...
Page 20: Rammer
Wc_si000836gb_fm10.Fm 20 rammer safety information safe operating practices when operating this rammer: ■ remain aware of the rammer’s moving parts. Keep hands, feet, and loose clothing away from the rammer’s moving parts. ■ when working near the edges of pits, slopes, trenches, and platforms, alway...
Page 21: Rammer
Wc_si000836gb_fm10.Fm 21 rammer safety information 1.5 service safety service training before servicing or maintaining the machine: ■ read and understand the instructions contained in all manuals delivered with the machine. ■ familiarize yourself with the location and proper use of all controls and ...
Page 22: Rammer
Wc_si000836gb_fm10.Fm 22 rammer safety information replacing parts and labels ■ replace worn or damaged components. ■ replace all missing and hard-to-read labels. ■ when replacing electrical components, use components that are identical in rating and performance to the original components. ■ when re...
Page 23: Rammer
Wc_si000836gb_fm10.Fm 23 rammer safety information 1.6 operator safety while using internal combustion engines operating safety when running the engine: ■ keep the area around the exhaust pipe free of flammable materials. ■ check the fuel lines and the fuel tank for leaks and cracks before starting ...
Page 24: Rammer
Wc_si000837gb_fm10.Fm 24 rammer labels 2 labels 2.1 label locations wc_gr010404 a a f m m e e h h k k d d l l b b g g j c c bs 50-2i/bs 60-2i/bs 70-2i bs 50-2/bs 60-2/bs 70-2, bs 65-v n r p q o wc_gr011507 bs 65-v.
Page 25: Rammer
Wc_si000837gb_fm10.Fm 25 rammer labels 2.2 label meanings a danger asphyxiation hazard. ■ engines emit carbon monoxide. ■ do not run the machine indoors or in an enclosed area unless adequate ventilation, through such items as exhaust fans or hoses, is provided. ■ no sparks, flames, or burning objec...
Page 26: Rammer
Wc_si000837gb_fm10.Fm 26 rammer labels b warning springs are compressed. Release cover slowly to avoid spring ejection. See the repair manual for proper disassembly instructions. C emission control information this engine/equipment meets u.S. Epa exhaust/ evaporative regulations for 2015. Engine fam...
Page 27: Rammer
Wc_si000837gb_fm10.Fm 27 rammer labels d guaranteed sound power level in db(a) e wacker neuson label f use only clean, filtered fuel. G turtle = idle/slow engine speed rabbit = full/fast engine speed h 1. Move the throttle to the idle position. 2. Close the choke. 5200015661 5200000314 5200000314 1 ...
Page 28: Rammer
Wc_si000837gb_fm10.Fm 28 rammer labels j engine oil tank ■ use only wacker neuson two-cycle or other fully syn- thetic oil meeting the nmma tc-w3, jaso fd, or iso-l-egd specification. Read the operator’s manual. K warning operation of this equipment may create sparks that can start fires around dry ...
Page 29: Rammer
Wc_si000837gb_fm10.Fm 29 rammer labels p locking lever label refer to selecting ramming stroke and adjusting ramming stroke for explanation of this label. Q caution cutting hazard. Moving parts under the housing cover can cut skin and catch clothing. Do not operate the machine while the housing cove...
Page 30: Rammer
Wc_tx003551gb_fm10.Fm 30 rammer lifting and transporting 3 lifting and transporting 3.1 lifting the rammer requirements ■ lifting device (crane or hoist) capable of supporting the rammer’s weight (see the identification plate on the rammer) ■ lifting gear (hooks, slings, and/or chains) capable of su...
Page 31: Rammer
Wc_tx003551gb_fm10.Fm 31 rammer lifting and transporting 3.2 transporting the rammer overview this rammer can be transported in a vehicle, or manually, depending on job site conditions and distance to be traveled. Notice: do not tow this rammer. Requirements ■ engine stopped and cool to the touch ■ ...
Page 32: Rammer
Wc_tx003551gb_fm10.Fm 32 rammer lifting and transporting continued from the previous page. If the rammer cannot be secured in the upright position, a. Drain the fuel tank to prevent fuel from leaking from the cap (c). B. Lay the rammer down only as shown and tie it to the vehicle at points (a) and (...
Page 33: Rammer
Wc_tx003551gb_fm10.Fm 33 rammer lifting and transporting notes.
Page 34: Rammer
Wc_tx003552gb_fm10.Fm 34 rammer operation 4 operation 4.1 preparing the machine for first use 1. Make sure all loose packaging materials have been removed from the machine. 2. Check the machine and its components for damage. If there is visible damage, do not operate the machine! Contact your wacker...
Page 35: Rammer
Wc_tx003552gb_fm10.Fm 35 rammer operation 4.2 recommended fuel for rammers with oil injection (bs 50-2i, bs 60-2i, bs 70-2i) if the rammer has a fuel tank (a) and an oil tank (b), it has oil injection—no premixing of the gasoline and oil is required. Mixing of the gasoline and oil is done automatica...
Page 36: Rammer
Wc_tx003552gb_fm10.Fm 36 rammer operation for rammers without oil injection (bs 50-2, bs 60-2, bs 70-2, bs 65-v, bs 65-v) if the rammer has a fuel tank (c) but no oil tank, the engine requires a two-cycle gasoline/oil mixture. Notice: use only the recommended gasoline/oil mixture to fuel this machin...
Page 37: Rammer
Wc_tx003552gb_fm10.Fm 37 rammer operation 4.3 refueling the machine requirements ■ machine shut down ■ engine cool ■ machine standing upright on the ramming shoe ■ fresh, clean fuel supply procedure perform the procedure below to refuel the machine. 1. Remove the fuel cap (a). 2. Fill the fuel tank ...
Page 38: Rammer
Wc_tx003552gb_fm10.Fm 38 rammer operation 4.4 filling the oil tank for rammers with oil injection (bs 50-2i, bs 60-2i, bs 70-2i) if the rammer has a fuel tank (a) and an oil tank (b), it has oil injection. The oil tank requires oil. Requirements ■ machine shut down ■ engine cool ■ machine standing u...
Page 39: Rammer
Wc_tx003552gb_fm10.Fm 39 rammer operation 4.5 purging the oil lines for rammers with oil injection (bs 50-2i, bs 60-2i, bs 70-2i) if the rammer has a fuel tank (a) and an oil tank (b), it has oil injection. The oil lines may need purging. When as needed: when air bubbles are visible in the oil suppl...
Page 40: Rammer
Wc_tx003552gb_fm10.Fm 40 rammer operation continued from the previous page. Purging the oil discharge line perform the procedure below to purge the oil discharge line. 1. Locate the oil discharge line (c). 2. If air bubbles are visible in the oil discharge line, they must be manually purged using th...
Page 41: Rammer
Wc_tx003552gb_fm10.Fm 41 rammer operation 4.6 position of the operator for optimal control, performance, and minimal hand/arm vibration, follow the guidelines below when using the machine. Grasp the handle with both hands as shown. Stand behind the rammer, walking slowly and guiding the direction of...
Page 42: Rammer
Wc_tx003552gb_fm10.Fm 42 rammer operation 4.8 starting, operating, and stopping the machine requirements ■ rammer is in serviceable condition and has been properly maintained ■ there is fuel in the tank starting the machine perform the procedure below to start the machine. 1. Move the throttle to th...