Www.Wackergroup.Com rammer bs 60-2 bs 70-2 operator’s manual 0158434en 006 1107 0 1 5 8 4 3 4 e n.
Bs 60/bs 70-2 table of contents 3 1. Foreword 5 2. Emission control system information 6 3. Safety information 13 3.1 operating safety ................................................................................ 14 3.2 operator safety while using internal combustion engines ................ 15 3...
Table of contents bs 60/bs 70-2 wc_bo0158434en_006toc.Fm 4 6. Technical data 35 6.1 rammer ...............................................................................................35 6.2 sound measurements .........................................................................36 6.3 vibratio...
Foreword wc_tx000001gb.Fm 5 california proposition 65 warning: engine exhaust, some of its constituents, and certain vehicle components, contain or emit chemicals known to the state of california to cause cancer and birth defects or other reproductive harm. 1. Foreword this manual provides informati...
Emission control system information wc_tx000030gb.Fm 6 2. Emission control system information source of emissions the combustion process produces carbon monoxide, oxides of nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions,...
Emission control system information wc_tx000030gb.Fm 7 replacement parts the emission control systems on your wacker engine were designed, built, and certified to conform with epa and california emissions regulations. We recommend the use of genuine wacker parts whenever you have maintenance done. T...
Emission control system information wc_tx000030gb.Fm 8 methanol - (methyl or wood alcohol) 5% by volume. You may use gasoline containing up to 5% methanol by volume, as long as it contains cosolvents and corrosion inhibitors to protect the fuel system. Gasoline containing more than 5% methanol by vo...
Emission control system information wc_tx000030gb.Fm 9 owner’s warranty responsibility: as the engine owner, you are responsible for the performance of the required maintenance listed in your owner’s manual. Wacker recommends that you retain all receipts covering maintenance on your engine, but wack...
Emission control system information wc_tx000030gb.Fm 10 to obtain warranty service: you must take your wacker product along with proof of original purchase date, at your expense, to any wacker authorized dealer during their normal business hours. Claims for repair or adjustment found to be caused so...
Emission control system information wc_tx000030gb.Fm 11 systems covered by this warranty parts descriptions fuel metering carburetor assembly exhaust system muffler air induction air filter housing air filter element* ignition flywheel magneto ignition module spark plug cap spark plug* miscellaneous...
Emission control system information wc_tx000030gb.Fm 12.
Safety information bs 60/bs 70-2 wc_si000120gb.Fm 13 3. Safety information this manual contains danger, warning, caution, notice and note callouts which must be followed to reduce the possibility of personal injury, damage to the equipment, or improper service. This is the safety alert symbol. It is...
Bs 60/bs 70-2 safety information wc_si000120gb.Fm 14 3.1 operating safety familiarity and proper training are required for the safe operation of the machine. Machines operated improperly or by untrained personnel can be dangerous. Read the operating instructions contained in both this manual and the...
Safety information bs 60/bs 70-2 wc_si000120gb.Fm 15 3.1.18 always guide the rammer in such a way that the operator is not squeezed between the rammer and solid objects. Special care is required when working on uneven ground or when compacting coarse material. Make sure to stand firmly when operatin...
Bs 60/bs 70-2 safety information wc_si000120gb.Fm 16 3.3 service safety a poorly maintained machine can become a safety hazard! In order for the machine to operate safely and properly over a long period of time, periodic maintenance and occasional repairs are necessary. 3.3.1 do not attempt to clean...
Safety information bs 60/bs 70-2 wc_si000120gb.Fm 17 3.4 label locations.
Bs 60/bs 70-2 safety information wc_si000120gb.Fm 18 3.5 safety and operating labels wacker machines use international pictorial labels where needed. These labels are described below: ref. Label meaning a this molded-in label contains important safety and operating information. If it becomes illegib...
Safety information bs 60/bs 70-2 wc_si000120gb.Fm 19 -- pull the rewind starter. -- open the choke. -- place the throttle control lever in the “stop” position. -- throttle control lever: 0 = stop turtle = start or idle rabbit = full or fast -- danger! Engines emit carbon monoxide; operate only in we...
Bs 60/bs 70-2 safety information wc_si000120gb.Fm 20 -- danger! No sparks, flames or burning objects near machine. -- shut off the engine before refueling. -- caution! Use only clean, filtered gasoline fuel. B warning! To prevent hearing loss, wear hearing protection when operating the machine. C wa...
Safety information bs 60/bs 70-2 wc_si000120gb.Fm 21 e caution! Always follow instructions when disconnecting fuel lines. Failure to do so may result in fuel squirting from fuel system. Read and understand the supplied operator's manuals before operating this machine. F for optimal control, performa...
Bs 60/bs 70-2 safety information wc_si000120gb.Fm 22 k choke: 0 = open l = closed l this engine is certified to operate on regular unleaded gasoline mixed with two cycle oil at 50:1-100:1 ratio. This rammer engine requires a two-cycle gasoline/oil mixture (50:1) -- this machine may be covered by one...
Operation bs 60/bs 70-2 23 4. Operation 4.1 application rammers are designed to compact loose soils and gravel to prevent settling and to provide a firm, solid base for the placement of footings, concrete slabs, foundations, and other structures. 4.2 recommended fuel this rammer engine requires a tw...
Bs 60/bs 70-2 operation 24 4.4 to start see graphic: wc_gr001461 4.4.1 open throttle to full position (c4). This will automatically turn on the flow of fuel. 4.4.2 if machine is equipped, pump the purge bulb (e) 6 to 10 times or until you see fuel in bulb. 4.4.3 close choke (b1). 4.4.4 pull starter ...
Operation bs 60/bs 70-2 25 4.5 to stop see graphic: wc_gr001461 4.5.1 place throttle in the idle position (c2). 4.5.2 shut off the engine by moving the throttle through the detent to the off position (c1). The engine will stop and the fuel valve will close. Note: if the throttle control wire should ...
Bs 60/bs 70-2 operation 26 4.7 proper compaction see graphic: wc_gr000045 4.7.1 run rammer at the full throttle position (a4) for maximum performance. 4.7.2 guide rammer with its handle. Allow machine to pull itself forward. Do not try to over-power the machine. 4.7.3 for best compaction, the shoe m...
Maintenance bs 60/bs 70-2 27 5. Maintenance 5.1 periodic maintenance schedule daily before starting after first 5 hours every week or 25 hours every month or 100 hours every 3 months or 300 hours every year check fuel level. Check air filter indicator. Replace as needed. Check ramming system oil lev...
Bs 60/bs 70-2 maintenance 28 5.2 air cleaner see graphic: wc_gr001168 never use gasoline or other types of low flash point solvents for cleaning the air filter. A fire or explosion could result. Notice: never run engine without main paper filter element (b). Severe engine damage will occur. Filter i...
Maintenance bs 60/bs 70-2 29 5.3 lubrication see graphic: wc_gr001464 ramming system check oil level: 5.3.1 tilt the machine backwards approximately 15° until the engine is level by placing a wedge under the shoe. 5.3.2 check the oil level through oil sightglass (d). Proper ramming system lubricatio...
Bs 60/bs 70-2 maintenance 30
Maintenance bs 60/bs 70-2 31 5.4 fuel lines see graphic: wc_gr0001493 always follow the instructions when disconnecting the fuel lines. Failure to do so may result in fuel leaking from the fuel system. To disconnect the fuel lines: 5.4.1 shut off the engine by moving the throttle through the detent ...
Bs 60/bs 70-2 maintenance 32 5.5 shoe hardware see graphic: wc_gr000055 on new machines, or after replacing shoe, check and tighten shoe hardware (a) after the first 5 hours of operation. Inspect hardware every week thereafter. Torque hardware as specified. 5.6 carburetor adjustments see graphic: wc...
Maintenance bs 60/bs 70-2 33 5.7 storage 5.7.1 drain the fuel from the tank. 5.7.2 start the engine and run it until remaining fuel is used. 5.7.3 remove the spark plug. Pour approximately 30 ml (1 oz.) of clean sae 10w30 engine oil into the cylinder through the spark plug opening. 5.7.4 pull the st...
Bs 60/bs 70-2 maintenance 34 5.9 troubleshooting problem / symptom reason / remedy engine does not start, or stalls. • no fuel in tank. • spark plug fouled. • fuel valve closed. Engine does not accelerate, is hard to start, or runs erratically. • improper fuel mix. Too much oil. • spark plug fouled....
Technical data bs 60/bs 70-2 35 6. Technical data 6.1 rammer item number: bs 60-2 0009388 0009417 0009421 bs 60-2 0009391 0009418 bs 70-2 0009397 0009399 0009424 0009425 0009427 rammer engine model type wm80 engine speed - full rpm 4400 ± 100 4600 ± 100 engine speed - idle rpm 1800 ± 100 clutch enga...
Bs 60/bs 70-2 technical data 36 6.2 sound measurements products are tested for sound pressure level in accordance with en iso 11204. Sound power level is tested in accordance with european directive 2000/14/ec - noise emission in the environment by equipment for use outdoors. • the sound pressure le...
2005-ce-bs60-2-70-2-q.Fm william lahner greg orzal vice president of engineering manager, product engineering wacker corporation date / datum / fecha / date ec declaration of conformity ce-konformitÄtserklÄrung declaraciÓn de conformidad de la ce dÉclaration de conformitÉ c.E. Wacker corporation, n9...
Wacker construction equipment ag · preußenstraße 41 · d-80809 münchen · tel.: +49-(0)89-3 54 02 - 0 · fax: +49 - (0)89-3 54 02-3 90 wacker corporation · p.O. Box 9007 · menomonee falls, wi 53052-9007 · tel. : (262) 255-0500 · fax: (262) 255-0550 · tel. : (800) 770-0957 wacker asia pacific operations...