WAGNER AC20 Operating Instructions Manual - page 38
#
#
#
+
+
+
+
#
#
Sender’s SMTP Password :
Send mail when Internet IP address changes:
Notes:
12.2.7 Automatic recording following motion detection or according to a
Schedule [50 - Recording (Alarm), Format and Motion Detection]
without
Note:
Enable Recording (Alarm):
Edit Schedule:
IMPORTANT NOTE:
* Enter the password for the email address (e.g.
the password for SamSample@gmail.com) from which you want the
emails to be sent here, and confirm with "Done".
Keep the factory setting.
The TLS encryption protocol that is required to send emails
The following settings are possible:
Both motion detection and automatic recording are activated:
Both settings are set to OFF
Only motion detection is activated,
recording:
Motion Detection is set to ON, Enable Recording is set to OFF
If motion is detected, a 59-second recording will automatically be saved
on the micro-SD card:
"Motion Detection" and "Enable Recording" are set to ON - no time
period is activated in the schedule
Compared to a continuous recording according to a schedule, recordings
following motion detection require less storage space, and it is easier to
search for events.
To be able to quickly switch on and off the recording following motion
detection, first set "Enable Recording" to ON in the settings. This can
be done directly via "Guard" [41] in the menu bar.
In accordance with the pre-set schedule, recordings are made during the
specified time periods. In each case for four full hours, divided into
sequential 15-minute files (i.e. 16 files are recorded during a 4-hour
period). The rest of the time, outside of the specified time periods, there are
no recordings or, depending on the settings, no recordings following
motion detection.
"Enable Recording" is set to ON, at least one time period has been
specified in the schedule (Edit Schedule), "Motion Detection" is set to
ON or OFF.
When set to ON, automatic recording is enabled
(depending on other settings either following motion detection or
according to a schedule); when set to OFF, it is disabled
Setting up the schedule for a continuous 4-hour recording,
divided into 15-minute sequences. You can activate individual time
periods, whole columns or rows, or the entire week (mark blue)
Factory setting: OFF
Factory setting: ON
Factory setting: No continuous recording
is not supported
by some providers. If necessary, set up a free email account, e.g. with
Google Mail (gmail).
If your "Sender's Email" is a Google account, it may be necessary to
activate access for "less secure apps" under "Security" in the email address
settings.
#
The revised schedule must be confirmed with "Save" two times: Once
after the time periods have been set, and another time immediately
afterwards.
Record frame: 15 or 30 frames/second are recorded
Factory setting: 15 images/second (requires less storage space)
Here you can format the micro-SD card that is
inserted in the camera. Please note, however, that all previously saved
data will be deleted in the process.
When set to ON, recording is activated by motion
detection; if set to OFF, it is disabled
Here you
#
#
#
#
Format MicroSD Card:
Enable Motion Detection:
Sensitivity:
Factory setting: ON
can adjust the motion detection sensitivity (1 - not
very sensitive / 10 - very sensitive)
ve your settings, press "Save".
Automatic recording is not automatically switched on/off too, i.e. changing the
settings to "ON" will only trigger a recording following motion detection if
"Enable Recording" is also set to ON.
Here you can change the camera name (Name) that is shown at the top of the
camera field for the corresponding mobile device.
In the "Name" field, enter the desired camera name and confirm with
"Save".
Factory setting: 5
Note:
12.4 Change the camera name [42 - Edit]
!
12.2.8 Update Firmware / Restore Factory Settings / Restart
Camera [51 - Tools]
Update Firmware:
Restore Factory Settings:
Restart System:
!
!
!
!
!
Only if required: press this field. The app will
automatically search for new firmware. If a new one is detected, confirm
with "OK" in the following field. The app will now load the firmware
automatically, after which the camera will shut down and restart
automatically. The connection LED [6] goes out. As soon as it is
permanently lit again, the camera has restored the connection to the
router. Now wait until the connection indicator [19] appears in the camera
field (if it does not appear, close and restart the app).
Here all settings are reset to the factory settings.
At the same time the camera is restarted, so that access must be set up
again on all mobile devices: Press this field and then confirm with "OK".
Now deleted the camera field of the old connection with "Delete" [43].
Once the camera's connection LED [6] starts to blink, carry out the initial
setup process as described in Chapter 6.1 from section six onwards. If more
mobile devices had access to the camera, delete the camera field there too
and then proceed as described in Chapter 9.2 from section two onwards.
To restart the camera automatically (retaining all
settings), press this field and then "OK". The connection LED [6] will go out.
Once it is permanently lit again, the camera has restored the connection to
the router. Now wait until the connection indicator [19] appears again in
the camera field (if it does not appear, close and restart the app).
Here you can switch motion detection on and off.
To sa
12.3 Activate/Deactivate motion detection [41 - Guard]
38 -
GB