WAGO I/O-SYSTEM 750 Manual - Device Description
WAGO-I/O-SYSTEM 750
Device Description
13
750-623 Supply Module DC 24V / 5-15V
Manual
Version 1.2.0
Pos: 17 /All e Seri en (Allgemei ne Module)/Ü berschriften/N eue Ü berschriften/Ebene 1Ger ätebeschrei bung - Ü berschrift 1 @ 3\mod_1233756084656_21.docx @ 27096 @ 1 @ 1
3
Device Description
Pos: 18.1 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebeschrei bung/Ei nlei tung/Anwendung/SY/Anwendung 750-0623 @ 11\mod_1317905453996_21.docx @ 80779 @ @ 1
The supply module 750-623 uses the DC 24 V input voltage to generate an
adjustable output voltage of DC 5 V, DC 8 V, DC 10 V, DC 12 V or DC 15 V.
Pos: 18.2 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebeschrei bung/Ei nlei tung/I/O-Beschrei bung/SY/I/O- Beschr eibung 750- 0623 @ 11\mod_1317905581177_21.docx @ 80783 @ @ 1
The input voltage is supplied via the CAGE CLAMP connections 24 V, 0 V and
ground from an external power source.
The output voltage is derived from the CAGE CLAMP connections + and -.
Furthermore, the power jumper contacts provide the output voltage to adjacent I/O
modules.
Pos: 18.3 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebeschrei bung/Ei nlei tung/I/O-Beschrei bung/Allgemei n/Ver weis auf Kapitel "Anschlüsse" @ 8\mod_1276775378035_21.docx @ 57956 @ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos: 18.4 /Dokumentation allgemei n/Glieder ungselemente/------Leerzeile------ @ 3\mod_1224662755687_0.docx @ 24460 @ @ 1
Pos: 18.5 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebeschrei bung/Ei nlei tung/LED-Anzeige/LED Versorg ung Eingang/Ausg ang @ 4\mod_1241687100406_21.docx @ 32677 @ @ 1
Two green status LED indicate the status of the input voltage and the output
voltage.
Pos: 18.6 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebeschrei bung/Ei nlei tung/LED-Anzeige/Ver weis auf Kapitel "Anzeigeelemente" @ 5\mod_1246010525000_21.docx @ 36194 @ @ 1
The meaning of the LEDs is described in the “Display Elements” section.
Pos: 18.7 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebeschrei bung/Ei nlei tung/Versorgung/Einspeisung 5 V ... 15 V, 0 V, Er de @ 11\mod_1317905843710_21.docx @ 80787 @ @ 1
The I/O module provides the 5V … 15V potential, 0V potential and earth
potential to subsequent I/O modules via the power contacts used as spring
contacts.
Pos: 18.8 /Serie 750 (WAGO-I/O-SYST EM)/Wichtige Erläuterungen/Sicherheits- und sonstig e Hinweise/Achtung/Achtung: M axi mal er Strom Einspeisung 750-0623 0,5 A / 1,0 A @ 11\mod_1317906232519_21.docx @ 80791 @ @ 1
Do not exceed maximum current via power contacts!
The maximum current that is permitted to flow through the power jumper contacts
is 0.5 A (1 A at an output voltage of 5 V). When configuring the system, this
current must not be exceeded.
Pos: 18.9 /Serie 750 (WAGO-I/O-SYST EM)/Wichtige Erläuterungen/Sicherheits- und sonstig e Hinweise/Achtung/Achtung: Ü berl astschutz 750- 0623 0,5 A /Achtung: Ü berlastschutz 750-0623 0,5 A / 1,0 A @ 17\mod_1383659220483_21.docx @ 136708 @ @ 1
Restricted overload protection!
The 750-623 supply module is short-circuit-protected. The overload protection
provides only limited protection. An overload of 150 % (0.75 A or 1.5 A) must
not be present for more than 5 seconds.
If this cannot be guaranteed, the 24 V power supply must be protected to prevent
damage to the 750-623 supply module.
Pos: 18.10 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Ei nleitung/Versorgung/Gal vanische Trennung Einspeisung nicht vor handen! @ 11\mod_1317908305666_21.docx @ 80795 @ @ 1
Input and output voltages are not electrically isolated from each other.
Pos: 18.11 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Ei nleitung/Versorgung/Anordnung der Potenti algruppen und Buskl emmen i n den Potenti algruppen beliebig @ 9\mod_1289992989792_21.docx @ 66482 @ @ 1
Both the potential groups and the individual modules within these groups can be
arranged in any combination when designing the field bus node.
Pos: 18.12 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Ei nleitung/Einsatzbereich/Einsatzbereich 750- xxxx alle Koppler/C ontroll er ohne Ei nschränkung @ 3\mod_1232541691906_21.docx @ 26522 @ @ 1
The I/O module 750-623 can be used with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750.
Pos: 19 /D okumentation allgemei n/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1