- DL manuals
- Walimex
- Camera Accessories
- PBS-400
- Instruction Manual
Walimex PBS-400 Instruction Manual
Summary of PBS-400
Page 1
1 copy of instruction manual portable studio flash system pbs-400 gewerbering 26 86666 burgheim tel. +49 84 32 / 9489-0 fax. +49 84 32 / 9489 - 8333 email: info@foto-walser.De www.Foto-walser.De.
Page 2: Content
2 content 1. How to understand this instruction manual .................................. 4 1.1 markings on the device ..................................................................... 4 1.2 markings in this manual .................................................................... 4 2. Importa...
Page 3: Well.
3 thank you very much for your confidence. We wish you much pleasure and success with your new device. The walimex portable studio flash system is particularly suitable for all photographic works, for which an uncomplicated handling and high mobility is important. You will achieve professional resul...
Page 4: Marking
4 1. How to understand this instruction manual 1.1 markings on the device this marking means, that your device meets the safety requirements of all relevant european directives. This marking means, that your device should be disposed in the local disposal points. 1.2 markings in the manual marking m...
Page 5: Important Safety Notes
5 2. Important safety notes warning risk of eye injury the optical radiation of the lamps could blind your eyes and lead to afterimages, if persons and animals look into the lamp directly. This could lead to injuries. Please avoid persons and animals looking into the flash directly. Warning danger o...
Page 6: Warning
6 warning danger of electric shock, fire through short-circuit a short-circuit could be caused through defect cables and through humidity or moisture. A short-circuit can warm up the conductors, so that there isolation will melt or even melt thoroughly. This could lead to fire. Please just use the o...
Page 7: Required Specifications.
7 the device itself, accessories and easily inflammable materials in close distance could catch fire. Please just use accessories and spare parts, which are conform to the required specifications. See technical specifications. Lamps, which are damaged or deformed through heat, should be exchanged im...
Page 8: Changing Accessories.
8 please handle the lamps with care to avoid bursting. Don´t touch the lamps with bare hands. Just touch the lamp at the plastic socket or wear clean cotton gloves or use a clean cloth. Avoid touching the flash tube accidentally when mounting or changing accessories. Only use accessories, which comp...
Page 9: Overview About The Parts
9 4. Overview about the parts a b carrying bag flash with handle and reflector c d e f g h i lamp protection cap accumulator charger power cord with power supply unit powerpack connection cord powerpack - flash j k connection cord powerpack - flash test button l jack for power cord with power supply...
Page 10: Quick-Start Guide
10 5. Quick-start guide advice: the detailed instruction for the following operations can be found in the respective chapters in this instruction manual. Keep the sequences of the following operation steps when using the device for the first time to avoid damages on the device. Warning please note t...
Page 11: Warning
11 6.2 mount/demount reflector switch off device. See switch the device on and off. Let the device cool down. Warning! Danger of burning on reflector and lamp. Let the device cool down approx. 30 minutes. Push the lateral release lever backwards and keep pressed. Put the reflector in the three openi...
Page 12
12 3. Let the device cool down. Caution! Danger of burning on the lamp. Let the device cool down for approx. 30 minutes. 4. Screw in lamp: screw in lamp carefully. Warning! Danger of electric shock. Always screw in the lamp as to avoid touching in the socket, when the device is switched on. 5. Screw...
Page 13: Operation Of The Device
13 7. Operation of the device 7.1 adjust tilt angle 1. Open tilt lever. 2. Adjust the required tilt angle. 3. Tighten tilt lever. 7.2 connect the device with the powerpack 1. Screw the connection cord powerpack-studio flash with the jack of the power pack and tighten it..
Page 14: Transportation And Storage
14 7.3 switch on powerpack and studio flash/adjust the output/switch off the studio flash and the powerpack can be switched on and off through the on/off tappet switch. 1. Switch on powerpack and studio flash: set on/off tappet switch on i. The modeling lamp lights up. You can trigger the studio fla...
Page 15: Solve Problems
15 6. Clean the device if necessary. See cleaning. 7. Put the device and all demounted elements in one carton and carry and store them according to the requirements in the technical specifications. See technical specifications. 9. Solve problems problem possible reason remedy device is switched on, ...
Page 16: 10. Maintenance
16 10. Maintenance 10.1 continuous inspections what you should do? Before every operation with every change check all cables and plugs for damages in case of damage: warning! Danger of electric shock and fire through short-circuit. The device should be repaired by an electrician immediately x check,...
Page 17: Portable Studio
17 portable studio flash system pbs-400 cleaning housing powerpack/studio flash use a microfiber cloth to remove light and stubborn dirt lamp wipe off with dust brush or dry, soft cloth advice: don´t clean the lamps with water. Even small residues on the lamps could lead to bursting 10.3 change lamp...
Page 18: Part Of The Device
18 part of the device item number additional accumulator for pbs-400 15956 13. Disposal and environment protection your device should be disposed free of charge at the local disposal points. 14. Technical specifications powerpack dimensions (lxwxd) approx. 21,5x16x7cm operating voltage dc12v chargin...
Page 19: Set
19 recycling time approx. 2-4sec. Modeling lamp 50w trigger mode sync cord, test button colour temperature 5300-5600k flash tube „plug-in“ power supply dc12v length of the cable approx. 150cm weight approx. 1180g set colour black/grey material plastic/metal total weight approx. 3400g.