Wallace international kinetic dc 15w gate operator kinetic dcs 15w gate operator kinetic dc 10fw gate operator kinetic dcs 10fw gate operator installation and maintenance manual wallace international 90 lowson cr. Winnipeg, manitoba. R3p 2h8.
Contents rev: a contents-1 introducing kinetic dc kinetic c omponents ....................................................................................................................................... I ntro- 1 i ntelligent f eatures s mart dc c ontroller ™ ........................................
Contents contents-2 rev: a u sing a s olar p owered o perator ...................................................................................................................... 2 - 6 design requirements & considerations ...............................................................................
Contents rev: a contents-3 chapter 5: bi-parting gate systems p ower r equirements ..................................................................................................................................................... 5 - 1 m aster & s lave w iring c onnections ..........................
© 2010 d0394 rev. B product & warranty registration enter the following information to register your wallace product. Please write legibly. Today’s date: _____________________ note: to extend the operator warranty beyond 1 year, you must return this registration within 60 days of purchase. Refer to ...
Kinetic components rev: a intro-1 kinetic components note: refer to parts & limited warranty for kinetic parts list..
Intelligent features: smart dc controller ™ intro-2 rev: a introducing kinetic dc thank you for purchasing our premium kinetic dc™ slide gate operator. At wallace international, we pride ourselves on quality. Our new line electromechanical gate operators include a number of unparalleled user benefit...
Technical support rev: a intro-3 for technical support, call your installer or authorized wallace international distributor. Obtain the serial number of your operator before calling. Refer to kinetic components on the front page. For the name of a distributor near you, call wallace international at ...
Installer’s check list intro-4 rev: a installer’s check list the following list provides a high level overview of the tasks involved in installing the kinetic dc gate operator. Take a moment to review the list and check off the items as you complete the install. Make sure gate installation complies ...
Important safety instructions rev: a s-1 safety requirements automatic gate operators provide user convenience and security. However, because these machines can produce high levels of force, it is imperative that gate operator system designers, installers and end users be aware of potential hazards ...
Important safety information s-2 rev: a • before attaching the operator to the gate, slide the gate in both directions. Make sure it is level and moves freely. A gate that slides easily reduces strain on operator components. Gravity should play no part in the opening or closing of the gate. • in the...
Important safety instructions rev: a s-3 safety standards – owner / user responsibility a moving gate can cause serious injury or death. Automatic gate operators move gates with high force. Make sure gates and gate operators are installed to reduce the risks of entrapment. Verify your gate and gate ...
Important safety information s-4 rev: a hazardous materials and proper disposal the kinetic operator uses sealed, state-of-the-art absorbed glass mat (agm) batteries wallace international highly recommends replacing used batteries with new agm-type batteries. The batteries used with the kinetic gate...
Secondary entrapment protection sensors rev: a s-5 secondary entrapment protection sensors kinetic is equipped with a primary, type a, inherent entrapment sensor (ies). Ul 325 safety standard compliance requires installation of secondary entrapment protection sensors, the number of which, depends on...
Secondary entrapment protection sensors s-6 rev: a identifying gate operator category & usage class the kinetic operator, according to ul 325 safety standards, falls in the slide gate and vertical barrier arm category for gate operators. Its usage class is determined by the area that the vehicular g...
Secondary entrapment protection sensors rev: a s-7 choosing secondary entrapment protection the site designer or installer must determine which secondary entrapment sensor devices will be installed with the kinetic operator to meet ul compliance. The type of entrapment sensor device systems are desc...
Secondary entrapment protection sensors s-8 rev: a emergency stop button an emergency stop button that is accessible from the outside of the operator is a requirement for compliance with ul 325 safety standards. The red emergency stop button is located inside a hole cutout on the kinetic cover. Pres...
Safety notices rev: a s-9 safety notices the following four levels of safety notices are used where applicable within this manual; each notice contains information specific to the situation. Indicates death or serious injury will occur if the hazardous situation is not avoided. Indicates death or se...
Common industrial symbols s-10 rev: a this page left intentionally blank.
Site overview & planning rev: a 1-1 installation chapter 1 site overview & planning kinetic dc 15w kinetic dc 10fw duty cycle: continuous duty cycle: continuous power: single phase, switch selectable power: single phase, switch selectable 115 volts, 3 amps, 50/60 hertz 115 volts, 3 amps, 50/60 hertz...
Installing the drive on gate post 1-2 rev: a installing the kinetic operator on gate posts rh & lh mounting options can be configured by the following steps: 1) remove the 4 - 10x1.5 x 20mm button head screws on the side of the operator that will be mounted to the gate post. See figure 1-2. Discard ...
Installing the drive on gate post rev: a 1-3 adjusting the drive height: 1) raise the operator to the correct height so that it engages the toothrack in the gate beam. Clearance between the toothrack and spur gear should be .11” (2.7mm); an 11ga tie wire can be used as a gauge to set the correct cle...
Installing the toothrack 1-4 rev: a installing the toothrack: hook toothracks together and slide them into rail throughout the entire length of gate. See figure 1-7 toothracks can be .80” (2cm) to 1.18” (3cm) shorter than gate length; it must not protrude past the end of the gate beam. See figure 1-...
Installing the drive on gate post rev: a 1-5 connecting the battery and turn dc power on: 1. Connect the red battery wire to its spade terminal. See figure 1-10 2. Turn dc power on. The usage class appears when power is first supplied to the operator. 3. To navigate within the setup menu, use the se...
Installing the drive on gate post 1-6 rev: a programming the initial setup menu: several sequential displays present information which must be configured before kinetic operator will function. Once the configuration is complete, the information is retained even when a power loss occurs. Table 1-1. M...
Installing the drive on gate post rev: a 1-7 establishing the open & close limits the learn limits display automatically appears after you set the gate weight. To set the open and close limits, take the following steps: 1. Hold the open button until the gate slides to full open. Release the open but...
Installing the drive on gate post 1-8 rev: a installing the target magnet figure 1-13 1. With the gate closed, mark the gate beam directly across from target sensor that is closest to the trailing edge of the gate. See figure 1-13. 2. Press the open button to move the gate a few feet and then press ...
Installing the drive on gate post rev: a 1- 9 8. To verify that the operator recognizes the target magnet, turn off both dc and ac power switches and watch the display go blank. Then, turn both switches on. The operator beeps indicating limit relearn mode. The gate then travels about 6 inches (15cm)...