WALTHER PILOT pilot maxi Operating Instructions Manual - page 3
Declaration of CE-Conformity
We,the manufacturers of the equipment, hereby declare under our sole responsibility
that the product(s) described below conform to the essential safety requirements. This
declaration will be rendered invalid if any changes are made to the equipment without
prior consultation with us.
Wuppertal, the 7th of July 2003
Name:Torsten Bröker
Position:Manager, Design and Development
This Declaration does not give assurance of properties in the sense of product liability.The safety instructions provi-
ded in the product documentation must be observed at all times.
Manufacturer
WALTHER Spritz-und Lackiersysteme GmbH
Kärntner Str. 18-30
D-42327 Wuppertal
Tel.: 0202 / 787-0
Fax: 0202 / 787-217
www.walther-pilot.de • Email:info@walther-pilot.de
Type Designation
Manual spray guns PILOT Maxi-HD / ND / MD
PILOT Maxi-HD Gravity-feed cup
V 11 613
PILOT Maxi-HD Material connection
V 11 614
PILOT Maxi-HD Suction cup
V 11 619
PILOT Maxi-MD Gravity-feed cup
V 11 615
PILOT Maxi-MD Material connection
V 11 616
PILOT Maxi-MD Suspended pressure cup
V 11 617
PILOT Maxi-ND Gravity-feed cup
V 11 633
PILOT Maxi-ND Material connection
V 11 634
PILOT Maxi-ND Suspended pressure cup
V 11 635
PILOT Maxi-HD-K Material connection
V 11 618
PILOT Maxi-HD-K Gravity-feed cup
V 11 626
PILOT Maxi-ND-K Material connection
V 11 620
PILOT Maxi-ND-K Suspended pressure cup
V 11 622
PILOT Maxi-ND-K Gravity-feed cup
V 11 623
Intended purpose
Processing of sprayable media
Applied Standards and Directives
EU-Machinery Directive 98 / 37 CE
94 / 9 EC (ATEX Directives)
DIN EN ISO 12100-1
DIN EN ISO 12100-2
EN 1127-1
Specification according 94 / 9 / CE
Category 2
Part marking
II 2 G c T 6
Tech.File,Ref.:
2404
special remarks :
The named product is intended for installation in other equipment. Commissioning is pro-
hibited until such time as the end product has been proved to conform to the provision of
the Directives 98 / 37 / CE.
i.V.
EG-Konformitätserklärung
Wir, der Gerätehersteller, erklären in alleiniger Verantwortung, daß das Produkt in
der untenstehenden Beschreibung den einschlägigen grundlegenden Sicherheits- und
Gesundheitsanforderungen entspricht. Bei einer nicht mit uns abgestimmten Änderung an
dem Gerät oder bei einer unsachgemäßen Verwendung verliert diese Erklärung ihre
Gültigkeit.
Wuppertal,den 7. Juli 2003
Name:Torsten Bröker
Stellung im Betrieb:Leiter der Konstruktion und Entwicklung
Diese Erklärung ist keine Zusicherung von Eigenschaften im Sinne der Produkthaftung. Die Sicherheitshinweise der
Produktdokumentation sind zu beachten.
Hersteller
WALTHER Spritz-und Lackiersysteme GmbH
Kärntner Str. 18-30
D-42327 Wuppertal
Tel.: 0202 / 787-0
Fax: 0202 / 787-217
www.walther-pilot.de • Email:info@walther-pilot.de
Typenbezeichnung
Handspritzpistolen PILOT Maxi-HD / ND / MD
PILOT Maxi-HD Fließbecher
V 11 613
PILOT Maxi-HD Materialanschluss
V 11 614
PILOT Maxi-HD Saugbecher
V 11 619
PILOT Maxi-MD Fließbecher
V 11 615
PILOT Maxi-MD Materialanschluss
V 11 616
PILOT Maxi-MD Hängedruckbecher
V 11 617
PILOT Maxi-ND Fließbecher
V 11 633
PILOT Maxi-ND Materialanschluss
V 11 634
PILOT Maxi-ND Hängedruckbecher
V 11 635
PILOT Maxi-HD-K Materialanschluss
V 11 618
PILOT Maxi-HD-K Fließbecher
V 11 626
PILOT Maxi-ND-K Materialanschluss
V 11 620
PILOT Maxi-ND-K Hängedruckbecher
V 11 622
PILOT Maxi-ND-K Fließbecher
V 11 623
Verwendungszweck
Verarbeitung spritzbarer Materialien
Angewandte Normen und Richtlinien
EG-Maschinenrichtlinien 98 / 37 EG
94 / 9 EG (ATEX Richtlinien)
DIN EN ISO 12100-1
DIN EN ISO 12100-2
EN 1127-1
Spezifikation im Sinne der Richtlinie 94 / 9 / EG
Kategorie 2
Gerätebezeichnung
II 2 G c T 6
Tech.File,Ref.:
2404
besondere Hinweise :
Das Produkt ist zum Einbau in ein anderes Gerät bestimmt. Die Inbetriebnahme ist so lange
untersagt, bis die Konformität des Endproduktes mit der Richtlinie 98 / 37 / EG festgestellt ist.
i.V.