WALTHER PILOT PILOT WA 800 Operating Instructions Manual - page 3
EG-Konformitätserklärung
Wir, der Gerätehersteller, erklären in alleiniger Verantwortung, daß das Produkt in der untenste-
henden Beschreibung den einschlägigen grundlegenden Sicherheits- und Gesundheitsanfor-
derungen entspricht. Bei einer nicht mit uns abgestimmten Änderung an dem Gerät oder bei
einer unsachgemäßen Verwendung verliert diese Erklärung ihre Gültigkeit.
Wuppertal,den 7. Juli 2003
Name: Torsten Bröker
Stellung im Betrieb: Leiter der Konstruktion und Entwicklung
Diese Erklärung ist keine Zusicherung von Eigenschaften im Sinne der Produkthaftung. Die Sicherheitshinweise der
Produktdokumentation sind zu beachten.
Declaration of CE-Conformity
We, the manufacturers of the equipment, hereby declare under our sole responsibility
that the product(s) described below conform to the essential safety requirements. This
declaration will be rendered invalid if any changes are made to the equipment without prior
consultation with us.
Wuppertal, the 7th of July 2003
Name: Torsten Bröker
Position: Manager, Design and Development
This Declaration does not give assurance of properties in the sense of product liability.The safety instructions provi-
ded in the product documentaion must be observed at all times.
Hersteller
WALTHER Spritz-und Lackiersysteme GmbH
Kärntner Str. 18-30
D-42327 Wuppertal
Tel.: 0202 / 787-0
Fax: 0202 / 787-217
www.walther-pilot.de • Email: info@walther-pilot.de
Typenbezeichnung
Automatische Spritzpistolen PILOT WA 800-Serie
WA 800-HD
(Hochdruck mit Innensteuerung)
V 20 800
WA 805-HD
(Hochdruck ohne Innensteuerung)
V 20 805
WA 810-HD-U
(Hochdruck-Umlauf mit Innensteuerung)
V 20 810
WA 815-HD-U
(Hochdruck-Umlauf ohne Innensteuerung)
V 20 815
WA 820-ND
(Niederdruck mit Innensteuerung)
V 20 820
WA 825-ND
(Niederdruck ohne Innensteuerung)
V 20 825
WA 830-ND-U
(Niederdruck-Umlauf mit Innensteuerung)
V 20 830
WA 835-ND-U
(Niederdruck-Umlauf ohne Innensteuerung)
V 20 835
WA 840-MD
(Mitteldruck mit Innensteuerung)
V 20 840
WA 845-MD
(Mitteldruck-ohne Innensteuerung)
V 20 845
WA 850-MD-U
(Mitteldruck-Umlauf mit Innensteuerung)
V 20 850
WA 855-MD-U
(Mitteldruck-Umlauf ohne Innensteuerung)
V 20 855
WA 870-HD-K
(Hochdruck-Kleberausführung ohne Innen.)
V 20 870
WA 871-HD-K-U (Hochdruck-Kleberausführung-Umlauf o. Innen.) V 20 871
WA 872-ND-K
(Niederdruck-Kleberausführung ohne Innen.)
V 20 872
WA 873-ND-K-U (Niederdruck-Kleberausführung-Umlauf o. Innen.) V 20 873
Verwendungszweck
Verarbeitung spritzbarer Materialien
Angewandte Normen und Richtlinien
EG-Maschinenrichtlinien 98 / 37 EG
94 / 9 EG (ATEX Richtlinien)
DIN EN 292 Teil 1
DIN EN 292 Teil 2
DIN EN 1953
Spezifikation im Sinne der Richtlinie 94 / 9 / EG
Kategorie 2
Gerätebezeichnung
II 2 G c T 5
Tech.File,Ref.:
2407
Besondere Hinweise :
Das Produkt ist zum Einbau in ein anderes Gerät bestimmt. Die Inbetriebnahme ist so lange unter-
sagt, bis die Konformität des Endproduktes mit der Richtlinie 98 / 37 / EG festgestellt ist.
i.V.
i.V.
Manufacturer
WALTHER Spritz-und Lackiersysteme GmbH
Kärntner Str. 18-30
D-42327 Wuppertal
Tel.: 0202 / 787-0
Fax: 0202 / 787-217
www.walther-pilot.de • Email: info@walther-pilot.de
Type Designation
Automatic Spray Gun PILOT WA 800-Models
WA 800-HD
(High pressure with internal control)
V 20 800
WA 805-HD
(High pressure without internal control)
V 20 805
WA 810-HD-U
(High pres.-circulation with internal control)
V 20 810
WA 815-HD-U
(High pres.-circulation without internal c.)
V 20 815
WA 820-ND
(Low pressure with internal control)
V 20 820
WA 825-ND
(Low pressure without internal control)
V 20 825
WA 830-ND-U
(Low pres.-circulation with internal control)
V 20 830
WA 835-ND-U
(Low pres.-circulation without internal c.)
V 20 835
WA 840-MD
(Mediem pressure with internal control)
V 20 840
WA 845-MD
(Medium pressure without internal control)
V 20 845
WA 850-MD-U
(Medium pres.-circulation with internal c.)
V 20 850
WA 855-MD-U (Medium pres.-circulation without internal c.)
V 20 855
WA 870-HD-K
(High pressure-adhesive version)
V 20 870
WA 871-HD-K-U (High pressure-adhesive version-circulation)
V 20 871
WA 872-ND-K
(Low pressure-adhesive version)
V 20 872
WA 873-ND-K-U (Low pressure-adhesive version-circulation)
V 20 873
Intended purpose
Processing of sprayable media
Applied Standards and Directives
EU-Machinery Directive 98 / 37 CE
94 / 9 EC (ATEX Directives)
DIN EN 292 Part 1
DIN EN 292 Part 2
DIN EN 1953
Specification according 94 / 9 / CE
Category 2
Part marking
II 2 G c T 5
Tech.File,Ref.:
2407
Special remarks :
The named product is intended for installation in other equipment. Commissioning is prohibited until such
time as the end product has been proved to conform to the provision of the Directives 98 / 37 / CE.