WANDERS KANDA User Manual And Installation Manual - Operation (Manual)
19
GB
Possible error messages:
t -POHTJHOBMT TFDTJHOBMTTFDOPTPVOEEVS
-
ing ignition
indicate that the batteries of the re-
ceiver are almost exhausted. (The appliance can still
be switched on for another 10 times after hearing this
signal.)
t TFDPOETDPOUJOVPVTTJHOBM
is an error message. It
may indicate that one of the cables is not connected
PSUIBUUIFi
O I
wTXJUDIJTOPUJOUIFi
I
” position.
t CSJFGTJHOBMT TFDTJHOBMTTFDOPTPVOE
JOEJDBUFUIBUJHOJUJPOPGUIFQJMPUnBNFBOEUIFNBJO
burner has failed. Possible reason is air in the pilot-
nBNFDPOOFDUJPO
Important: If the pilot flame has extinguished you must
wait at least 5 MINUTES before repeating the above ac-
tions.
Setting the height of the flames
t "GUFSJHOJUJPOPGUIFCVSOFSUIFnBNFIFJHIUXJMMBV
-
tomatically be in the highest position.
t $POUJOVPVTMZ QSFTT CVUUPO
d
UP MPXFS UIF nBNFT
and to extinguish the burner (extinguishing the fire:
i
STAND BY
w#SJFnZQSFTTJOHCVUUPO
d
will gradu-
BMMZMPXFSUIFnBNFT
t 1SFTTJOH CVUUPO
c
XJMM HJWF IJHIFS nBNFT #SJFnZ
pressing button
d
XJMMHSBEVBMMZSBJTFUIFnBNFT
Switching off the appliance
t 1SFTTCVUUPO
d
UPEFDSFBTFnBNFIFJHIUBOEUPTXJUDI
off the appliance.
t 5IFO QSFTT i
OFF
” button
e
to switch off the whole
BQQMJBODFJODMVEJOHUIFQJMPUnBNF
t *GUIFBQQMJBODFXJMMOPUCFVTFEGPSBMPOHFSUJNFJUJT
advisable to close the gas tap in the gas supply pipe.
Important: If for whatever reason the pilot flame has ex-
tinguished you must wait 5 MINUTES before lighting the
pilot again.
Malfunctioning
If it appears that the signals of the remote control are not
(properly) picked up by the stove (receiver), this may be
caused by:
t %FBECBUUFSJFTSFQMBDFCBUUFSJFT
t "OFMFDUSJDBMQSPCMFNUPCFSFNFEJFECZQSFTTJOHUIF
i
RESET
” button on the receiver.
t 4IPVMEUIFBQQMJBODFTIVUJUTFMGPGGSFHVMBSMZZPVOFFE
to contact your installer.
Operation (manual)
If the batteries are dead or if the receiver is defect, the
stove can also be manually operated. First disengage the
ignition cable (piezo) cable from the receiver and care-
fully slide it onto the piezo connection of the gas control
block.
Ignition of the fire
1. Open the gas shut-off cock, which is fitted on the
gas pipe to the appliance.
1SFTTi
O I
” switch
g
on the gas control block in the
i
I
” position.
3. Turn motor switch
i
on the gas control block com-
pletely to the right; the switch will make a ticking
sound.
4. Turn
control
switch
h
on the gas control block to
the
MAN
position; an opening in the control switch
will become visible
j
.
5. Press the metal pin in the opening, with a pointed
JOTUSVNFOUFHBQFO5IFHBTXJMMnPXUPUIFQJ
-
lot.
5PJHOJUFUIFQJMPUnBNFQSFTTUIF TRVBSFJHOJUJPO
switch
k
OFYU UP UIF i
O I
” switch) several times
while keeping the pressure on the metal pin. Check
UISPVHIUIFHMBTTXJOEPXJGUIFQJMPUnBNFJTCVSO
-
ing.
7. Once the pilot is burning, keep the metal pin
pressed for another 10 seconds, and then release
g
h
h
g
i
j
k