Tel: +86-579-82346658 email: sales@wanhao3dprinter.Com web: www.Wanhao3dprinter.Com user manuel resolution 0.02mm speed 300mm/second software: wanhao maker 3d ＷＡＮＨＡＯ ＰＲＩＮＴＥＲ duplicator5s.
Duplicator 5s.
Wanhao is excited to welcome you to the world of the wanhao duplicator 5s. .Following this guide will help with duplicator 5s this user manual is designed to help you start your experience with duplicator 5s. .Within these pages, we want to show you how simple and easy it is to produce great prints....
28kg(62lbs) 39kg(86lbs) width 565mm length 605mm height 950mm 295*195*575mm height 810mm width 415mm length 455mm data print technology fused filament fabrication(fff) build volume layer resolution ultra high 20 micron high 60 micron medium 100 micron low 200 micron position precision x 12.5 micron ...
Ｂ１ Ｕｎｂｏｘｉｎｇ 1. Place the duplicator 5s box on the ground next to a clean, flat workspace. 2. Cut of the rope and discard the top cardboard insert. 3. Now remove the inner cardboard box, and take the duplicator 5s out of its box. 4. Now you can clear away the cardboard inserts and remove the accessor...
Accesoires that comes with this 3d printer.All the following parts should be in the box,please besides your duplicator 5s supplied with sd card in the 3d printer ,there are a lot of essential Ｂ２ Ｗｈａｔ＇ｓ ｉｎ ｔｈｅ ｂｏｘ check contents. 1 pc printer 1 pc bulid plate 1 pc spool holder 1 pc clamp 1 pc usb cab...
1. Led display 2. Push and rotate button 3. Extruder cable 4. Filament tube 5. Mk10 extruder 6. Building plate 7. Building plate screw 8. Spool holder 9. Usb socket 10. Power switch 11. Material feeder 12. Power socket Ｂ３ Ｄｕｐｌｉｃａｔｏｒ ５Ｓ ｇｌａｎｃｅ.
7 . The main cable in the power brick can be 6 . The plug has a sliding collar. When 5 . Next take the power plug out of the wall slot.The flat side of the power plug s b switch and u has to face towards the top of the duplicator5 . Step is to make sure the duplicator5 turned off. This the duplicato...
Auto- homing f inshed 4. Prepare a name card, wait until 1. Navigate the rotate button and push the button 2. Navigate the rotate button to utility and push the button 7. Navigate to step2, 3 and 4 6. Insert one name card between the nozzle and plate(0.1mm thick) 5. Push the button and adjust nut be...
Guided along the filament guide,with the filament 1. Now that we have completed the initial leveling tasks we [continue] and go to the step where we are going to insert filament material in the material feeder. Navigate the control button to ---utility---load 2. Wait the extruder to heat up to 220'c...
Installation wiz ard will continue to finish the printer and ready to become your physical object. Your model at the background. Faster than ever.From there it is just seconds away from your object, wanhao maker’s slicer engine prepares program that helps you install the lastest firmware as well as ...
Wanhao maker interface 1. Load file click this button to load an object to your print area. You can add as many objects as you can fit on the plate. 2. Start making press this button to start slicing. There will be more options after pressing the button 3. Save toolpath (sd) when you press this butt...
That your file has been saved. 7. .When finished saving it will give you the notification * .I file into sd card directly. Range of the printing table. 3.After you put the file in,please check if it is in the the file on the sd card.Or you can copy the toothpath use your own stl file. Preparing a 3d...
