Wasp WWS800 User Manual

Other manuals for WWS800: User Manual, Reference Manual, User Manual, User Manual

Manual is about: Bluetooth Wireless Scanners

Page of 22

Download

Print this page

Bookmark us

WWS800/850 Bluetooth Wireless Scanners

User’s Manual

WARNING

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

If applicable, as below

FCC Caution: To assure continued compliance, (example – use only shielded

interface cables when connecting to computer or peripheral devices). Any changes

or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 20 cm between the radiator & your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

1 2 3 4 5 6 7 Next › »

Summary of WWS800

Page 1
Wws800/850 bluetooth wireless scanners user’s manual warning this equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential ins...
Page 2
Table of contents 1. Introduction...........................................................................................1 2. Base installation ................................................................................2 2.1 p ower u p the b ase s tation ........................................
Page 3
8. Data output format.........................................................................29 8.1 c haracter s ubstitution .....................................................................29 8.2 p refix / p ostfix c ode ............................................................................
Page 4
1 1. Introduction this manual described how to operate and configure the wws800/850 wireless barcode scanner and is divided into two sections. The first section describes the installation, operation and programmable features of the scanner. The second section contains the setup barcodes used to conf...
Page 5
3 2.2 power up the wws800/850 when you receive your wws800/850, the battery will be packaged separately. Please insert the battery into the bottom of the scanner and lock the battery into place by pushing up on the clip. The scanner will beep and the led will be light up when the device is powered o...
Page 6
5 2.4.3 dc jack insert the power supply to the dc jack at bottom of the scanner. When charging, the scanner led will flash red. When the battery is fully charged, around 4 hours from completely empty battery, the led stays on solid red. 2.5 interface setting once you have “paired” the scanner and ba...
Page 7
7 • continuous mode: the scanner is always scanning. • auto power off mode: the scanner will start scanning once the switch is triggered. The scanning continues until a preset scanning period (scanner time-out duration) is expired. Unlike the auto off mode, the scanner will continue to scan and the ...
Page 8
9 • ean8 (with or without addon) • ean13 (with or without addon) • code 93 • code 128 • ean 128 • msi • telepen • plessey 3.9 negative barcodes the scanner can be configured to read negative barcodes. Normally, barcodes are printed with the color of the bars darker than that of the spaces. But for n...
Page 9
11 4.1.4 capital lock status in order to send alphabets with correct case, the scanner needs to know the capital lock status of the keyboard. Incorrect settings may result in reversed case of alphabets being transmitted. There are 3 options to this parameter: on, off, or auto detection. If this para...
Page 10
13 the scanner is out of signal range and data will transmitted to server when the scanner is back to the service range. The wws800/850 can work offline and store the reading data into the internal flash memory for later upload to the host. The stored data can be up to 128kbytes. 4.4.1 transmit buff...
Page 11
15 the initial (first time) connection setup, this setting must be enabled. User can disable this setting for security reasons after initial connection setup is completed. 5.1.4 update settings after all the desired settings are completed, the “update” barcode must be scanned to make the new setting...
Page 12
17 6.1.2 reset connection scan the “reset connection” when switch connection from one pc to another pc. The scanner will re-start itself after this barcode is read. 6.1.3 authentication & pin code the 800/850 scanner can do connection authentication if communication security is desired. Once this se...
Page 13
19 6.3 configuring bluetooth device driver please follow the procedures below to configure the bluetooth driver on the host system. Please note that, when searching nearby bluetooth devices on host computers, the 800/850 scanner will come out with the serial number as their device name. Please check...
Page 14
21 8. The scanner is ready to use. Please click ok button. 6.3.2 widcomm bluetooth driver 1. Click icon at pc. 2. Click find bluetooth devices icon at my bluetooth places. 22 3. Right click the 800/850 scanner and select pair device. 4. Input pin code and click ok button. 5. Right click 800/850 scan...
Page 15
23 6. Click pc remote commander icon. 7. Click yes button. 8. When the green arrow icon is displayed, the connection is ready. No 24 7. Symbology parameters this section describes user configurable parameters that are pertaining to barcode symbologies. 7.1 code39 • standard / full ascii code 39: use...
Page 16
25 • checksum transmission: this parameter specifies whether the checksum character is included in the data being transmitted. • code length qualification: because of the weak structure of the 2 of 5 codes, a partial scan has a high probability of decoding as a valid but shorter 2 of 5 codes (known ...
Page 17
27 • checksum verification: three kinds of checksum calculations can be implemented into msi code: single modulo 10, double modulo 10, or modulo 11 & 10 checksum. If the checksum character is incorrect, the barcode will not be read. • checksum transmission: user can control the checksum transmit ion...
Page 18
29 8. Data output format data read by the scanner will be processed in the following sequence (rs-232, keyboard wedge and usb interfaces). 1) the character substitution is performed on the barcode data. 2) the code id and the length code are inserted at the beginning of the data as shown below. [cod...
Page 19
31 9. Data editing the wws800/850 scanner provides advanced data editing functions for data formatting. Data editing is performed according to user configured editing formats. Up to three editing formats can be configured. Data is divided into fields by user specified rules. These fields together wi...
Page 20
33 always included in the field. User though, has the option of discarding this terminating string. • field length: the field division can be simply specified by the field length. The scanner will assign the next specified number of characters into the field. 9.6 additional fields user can create up...
Page 21
35 10. Configuring your wws800/850 the configuration of wws800/850 scanner is done by reading the setup labels contained in the configuration manual (the second part of this manual). This section describes the procedure of configuring the scanner. Some configuration examples are also given in this s...
Page 22
37 used. These parameters are: prefix code, postfix code, code id, and additional fields of editing formats. The available key type/status settings can be selected will be described briefly. The configuration procedures for character string parameters are shown below. Parameter label key type / stat...