1. DL manuals
  2. Wasp
  3. Barcode Reader
  4. WWS800
  5. User Manual

Wasp WWS800 User Manual

Other manuals for WWS800: User Manual, Reference Manual, User Manual, User Manual
Manual is about: Bluetooth Wireless Scanners

Summary of WWS800

  • Page 1

    Wasp technologies wws800 cordless scanner user’s manual document number: w800-a1 release date: february 18, 2004  2004, wasp ® technologies all rights reserved. Warning this equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of fcc rules....

  • Page 2

    Table of contents 1. Introduction ........................................................................1 2. Installation..........................................................................2 2.1 power up the wws800 base station ................................2 2.2 power up the wws800 cordle...

  • Page 3

    The wws800 cordless barcode scanner is the first wasp technologies scanner utilizing bluetooth technology. The scanner has a remote range of over 160 feet and a battery life of over 50,000 scans. The wws800 uses a ccd long-range linear imager. This manual contains all the information needed to opera...

  • Page 4

    When you receive your wws800 cordless scanner, it will be in an off mode. This is done to conserve power and for transportation purposes. At the base of the scanner you will find a small pin hole. Using a straightened paper clip insert the end of the paper clip into the pin hole and then remove. The...

  • Page 5

    # $ ! Once you have “paired” the scanner and base, you need to specify the interface type to your pc. The interface settings are stored in the base. So ensure that you have rf connection between your scanner and base prior to setting the interface type. For details on selecting interfaces please ref...

  • Page 6

    • alternate mode: the scanner will start scanning once the switch is triggered. The scanner will continue scanning until the switch is triggered again. • momentary mode: the scanner will scan as long as the switch is depressed. • repeat mode: the scanner is always scanning just like continuous mode....

  • Page 7

    3 $ 4 5 the wws800 is a multi-interface scanner. It can be used as a keyboard wedge scanner or a usb scanner. The output interface can be programmed using the setup bar codes found in the reference guide. Please ensure that you have an rf connection between the scanner and the base prior to selectin...

  • Page 8

    ' - " - the scanner can work offline and store data in the internal flash memory for later upload to the host. The stored data can be up to 32kbytes. ' - "' this setting enables or disables the memory function of the scanner. * the clear label will enable the user to clear or erase the data in the s...

  • Page 9

    # ! After all the desired settings are completed, the “update” bar code must be scanned to make the new settings effective. The scanner will re-start itself after the “update” bar code is scanned. # # , - the scanner will stay active only for one minute waiting for connection. If there is no connect...

  • Page 10

    Select “bluetooth serial port” from the list. Click “property” button. “secure connection”. If you have enabled the authentication and have configured a pin code on the wws800, leave “secure connection” checked. Otherwise, uncheck it. Click “apply” and “ok” click “ok” to go back to “my bluetooth pla...

  • Page 11

    Double click “sw3000006”. This will bring up a screen showing the available services on this device. We can see that there is only one service available on “sw3000006”. The service name is “com1 on sw3000006”, which is the bluetooth serial port service. Double click on the service. This will start t...

  • Page 12

    + "- / !" - this section describes user configurable parameters pertaining to bar code symbologies. + 0 • standard / full ascii code 39: user can choose to read either standard code 39 or full ascii code 39 by configuring this parameter. • start/stop transmission: this parameter specifies whether th...

  • Page 13

    +. ( • convert to ean13: if this parameter is enabled, the upca read will be expanded into ean13, and the following processing will follow the parameters configured for ean13. • system number transmission: if this parameter is enabled, the system number will be included in the data being transmitted...

  • Page 14

    . * 3 - data read by the scanner will be processed in the following sequence (keyboard wedge then usb interfaces). 1) the character substitution is performed on the bar code data. 2) the code id and the length code are inserted at the beginning of the data as shown below. [code id] [length code] [da...

  • Page 15

    * = ! The wws800 scanner provides advanced data editing functions for data formatting. Data editing is performed according to user configured editing formats. Up to three editing formats can be configured. Data is divided into fields by user specified rules. These fields, together with user configur...

  • Page 16

    + ( you can create up to five additional fields for each editing format. Each additional field can have at most four characters. The additional fields are numbered af1 to af5 accordingly. . , - > after the data fields and the additional fields are configured, you can now program the transmission seq...

  • Page 17

    0 $! !" configuring the wws800 scanner is done by reading the setup labels contained in the reference guide. This section describes the procedure of configuring the scanner. Some configuration examples are also given in this section for illustration. 0 = $! ' to start the configuration, the “ enter ...

  • Page 18

    Parameter label key type / status label two hexadecimal labels "validate" label for example, to configure the prefix code to be “ab”, the “prefix code” label is first read, and then the hexadecimal digit labels “4”, “1”, “4”, and “2” are read, and finally, the “validate” label to complete the settin...