Waterproof Moto-series Installation Manual - page 6
4. Specification
Moto-620 / 625 / 630
2 Channel 40 watts waterproof outdoor Class D Amplifier for iPod / MP3 / portable CD players or
any satellite radio system
Two jet-engine speakers including (2”/ 2.5”/ 3”for selection) with 3 different available mounting
styles
Waterproof and corrosion-proof amplifier case with mounting bracket
Waterproof volume control with 6fit cable and 3.5mm mini plug
Protection :Thermal and short circuit protection and auto recovery feature
AUX-IN 3.5 mm jack with rubber cover
Automatically turn on power and automatically turn off power (30 - 50 seconds)
Amplifier : IP68 rating / CE certificate / E-Mark / RoHS conformed
Speaker : IP65 rating / IEC-268-5 (100 hrs tested) / RoHS conformed
Frequency response : 20 Hz – 20000 Hz
Impedance : 4 ohms
Output power : 20W/Chennal 4 ohm load from 12V DC
30W/Chennal 4 ohm load from 24V DC
Power supply : From 10V - 26V DC
SNR : 98 dB / 12V 102 dB / 24V
5
2
Moto-820 / 825 / 830
4 Channel 80 watts waterproof outdoor Class D Amplifier for iPod / MP3 / portable CD players or
any satellite radio system
Four jet-engine speakers including (2”/ 2.5”/ 3”for selection) with 3 different available mounting
styles
Waterproof and corrosion-proof amplifier case with mounting bracket
Waterproof volume control with 6fit cable and 3.5mm
mini
plug
Protection :Thermal and short circuit protection and auto recovery feature
AUX-IN 3.5 mm jack with rubber cover
Automatically turn on power and automatically turn off power (30 - 50 seconds)
Amplifier : IP68 rating / CE certificate / E-Mark / RoHS conformed
Speaker: IP65 rating / IEC-268-5 (100 hrs tested) / RoHS conformed
Frequency response : 20 Hz – 20000 Hz
Impedance : 4 ohms
Output power : 20W/Chennal 4 ohm load from 12V DC
30W/Chennal 4 ohm load from 24V DC
Power supply : From 10V - 26V DC
SNR : 98 dB / 12V 102 dB / 24V
1) Standard Flat Surface:
1. Mount the plastic bracket on the chosen flat surface with the
screws (4×12 mm) provided in the package
2. Hold the jet-engine speaker in position and secure the
mounting with a screw (4×15 mm) and a nut
3. Adjust the projecting angle of the speaker and tighten any
loose screws
2) Handle bar:
1. Select the appropriate mounting clamp from the package
2. Hold the jet-engine speaker in position and secure the
mounting to the clamp with a screw (4×15 mm) and a nut
3. clamp it around the handle bar
4. Adjust the angle of the clamp. Tighten the clamp with a screw
(4×25 mm) and a nut.
5. Adjust the projecting angle of the speaker and tighten any
loose screws
3) Mirror side:
1. Select the appropriate mounting bracket from the package and
dissemble the side mirror
2. Select the appropriate mounting style of the bracket. To
position the speakers at a higher level see depiction A; to
position the speakers at a lower level see depiction B
3. Hold the jet-engine speaker in position and secure the
mounting to the holder with a screw (4×15 mm) and a nut
4. Screw the holder to the stainless steel bracket with a 4×6 mm
screw and adjust the angle
5. Reassemble the side mirror on the stainless steel bracket as
shown
6. Secure a tight mounting to prevent detachment of the bracket
or the mirror
7. Adjust the final projecting angle of the speaker
8. Check for any loose screws and nuts
A
B
8. Loudspeaker Installation
Manual
9. Amplifier functional test
It is advised to carry out the following product testing procedures to test the amplifier for the first time.
The automatically on/off system could help to save electricity in various situations. The LED light
indicates the status of the amplifier. It is only switched on if the amplifier is turned on.
The amplifier would be turned on automatically in the following situations:
1) Connect the audio device (e.g. MP3 player) to the amplifier with the 3.5 mm Stereo Male to Male
Cable. Turn the volume control towards 10 o’clock position and play any music. The LED light should
be switched on and the amplifier should come to live immediately.
2) If the music device is already playing, connecting it to the amplifier should also turn on the
amplifier automatically.