1 visit our website at http://watt-age.Globalhobby.Com for information on other wattage products specifications: ● wing span: 33 inches ● wing area: 165 square inches ● length: 27 inches ● weight rtf: 12 ounces ● ● ● ● ● wing loading: 10.5 ounces per square foot ● functions: ailerons, elevator, rudd...
2 need help or have any questions? Call us at 1-714-963-0329 or send us an email to service@globalhobby.Net table of contents this r/c airplane is not a toy! If misused or abused, it can cause serious bodily injury and/or damage to property. Fly only in open areas and preferably at a dedicated r/c f...
3 visit our website at http://watt-age.Globalhobby.Com for information on other wattage products this instruction manual is designed to guide you through the entire final assembly process of your new airplane in the least amount of time possible. Along the way you'll learn how to properly assemble y...
4 need help or have any questions? Call us at 1-714-963-0329 or send us an email to service@globalhobby.Net this section describes our recommendations to help you in deciding which types of accessories to purchase for your new odyssey ep arf. Please read through this entire section very carefully. W...
5 visit our website at http://watt-age.Globalhobby.Com for information on other wattage products here's a list of what we used to finish our odyssey ep arf: qty. 1 759134 hitec electron 6 micro receiver hitec dual conversion fm rx crystal qty. 3 444035 cirrus cs-6.2 micro servos qty. 1 128482 wattag...
6 need help or have any questions? Call us at 1-714-963-0329 or send us an email to service@globalhobby.Net we have organized the parts as they come out of the box for easier identification during assembly. Before you begin assembly, group the parts as we list them below. This will ensure that you h...
7 visit our website at http://watt-age.Globalhobby.Com for information on other wattage products the covering material used on the wattage odyssey ep arf is real iron-on, heat-shrink covering material. It is possible with heat and humidity changes that the covering on your airplane may wrinkle or sa...
8 need help or have any questions? Call us at 1-714-963-0329 or send us an email to service@globalhobby.Net ❑ kwik bond 5 minute epoxy ❑ # 1 phillips head screwdriver ❑ excel modeling knife ❑ 220 grit sandpaper w/sanding block ❑ masking tape you'll need the following parts from the kit: ❑ (1) fusela...
9 visit our website at http://watt-age.Globalhobby.Com for information on other wattage products ❑ mix a generous amount of 5 minute epoxy and carefully apply a thin layer to the root ribs on both wing panels. Warning for maximum wing strength, make sure to cover the entire surface of both root ribs...
10 need help or have any questions? Call us at 1-714-963-0329 or send us an email to service@globalhobby.Net ❑ kwik bond 5 minute epoxy ❑ kwik bond thick c/a ❑ # 0 phillips head screwdriver ❑ magnum z-bend pliers ❑ wire cutters ❑ needle nose pliers ❑ excel modeling knife ❑ electric or hand drill you...
11 visit our website at http://watt-age.Globalhobby.Com for information on other wattage products ❑ carefully slide the plain end of the pushrod wire (with the control horn still attached) into the nylon pushrod housing in the right side of the fuselage (looking from the back of the airplane). ❑ car...
12 need help or have any questions? Call us at 1-714-963-0329 or send us an email to service@globalhobby.Net ❑ place a small "4-point" servo horn onto the elevator servo, making sure that the servo horn is centered and points toward the fuselage side. ☞ you might have to cut off the excess arms from...
13 visit our website at http://watt-age.Globalhobby.Com for information on other wattage products ❑ install the control horn to the left side of the rudder, making sure that the pushrod attachment holes are positioned over the rudder hinge line and that the control horn is lined up with the pushrod ...
14 need help or have any questions? Call us at 1-714-963-0329 or send us an email to service@globalhobby.Net ❑ using a modeling knife, cut away and remove the two lower arms from a "4-point" servo horn. Your servo horn should look like the drawing at left. ❑ plug the aileron servo into the receiver....
15 visit our website at http://watt-age.Globalhobby.Com for information on other wattage products ❑ place the servo horn onto your servo, making sure it's centered and that the arms face toward the leading edge. ❑ make a z-bend in each pushrod wire where they cross the second hole out from the cente...
16 need help or have any questions? Call us at 1-714-963-0329 or send us an email to service@globalhobby.Net step 2: installing the receiver ❑ plug the elevator, rudder and esc leads into their proper slots in your receiver. ❑ mount the receiver to the fuselage floor, directly behind the battery mou...
17 visit our website at http://watt-age.Globalhobby.Com for information on other wattage products ❑ ruler section 10: balancing the odyssey ep arf you'll need the following tools and supplies: ❑ masking tape important it is critical that your airplane be balanced correctly. Improper balance will cau...
18 need help or have any questions? Call us at 1-714-963-0329 or send us an email to service@globalhobby.Net section 11: control throws & flight setup we recommend setting up the odyssey ep arf using the control throws listed below. These control throws are suggested for the best overall flight perf...
19 visit our website at http://watt-age.Globalhobby.Com for information on other wattage products section 12: preflight check & safety ● check the operation of the throttle. To do this, do the following: a) plug the flight battery into the esc and turn on the radio system. Warning do not turn the re...
20 need help or have any questions? Call us at 1-714-963-0329 or send us an email to service@globalhobby.Net section 13: flying the odyssey ep arf the odyssey ep arf can take off from the ground or be hand-launched. We recommend ground take-offs only from hard, smooth surfaces. Since the wheels are ...
21 visit our website at http://watt-age.Globalhobby.Com for information on other wattage products elevator: the elevator is the control surface on the back of the airplane that moves up and down. This surface controls pitch. Epoxy: a two-part glue containing a resin and a hardener. Epoxy is availabl...
22 need help or have any questions? Call us at 1-714-963-0329 or send us an email to service@globalhobby.Net.
23 visit our website at http://watt-age.Globalhobby.Com for information on other wattage products telling us what you like and don't like determines what model kits we make and how we make them. We would appreciate it if you would take a few minutes of your time to answer the following questions abo...
24 need help or have any questions? Call us at 1-714-963-0329 or send us an email to service@globalhobby.Net fold along dotted line fold along dotted line global hobby distributors attn: global services 18480 bandilier circle fountain valley ca 92728-8610 post office will not deliver without proper ...
