WATT AGE Super Impress II EP ARF Instructions For Final Assembly - page 5
5
Here's a List of What We Used to Finish Our Super Impress II EP ARF:
✦
✦
✦
✦
✦IMPORTANT✦
✦
✦
✦
✦
When choosing the propeller and flight battery for your particular motor, double-check that the power system will not draw
more amperage than your motor is designed for.
The part number listed for the Cirrus servos is compatible with all radio control systems. This servo uses a universal connector. The part
number listed for the Cirrus MRX-4II Micro receiver is compatible with all radio control systems. This receiver features auto-shift select. The
part number listed for the Cirrus servo extension is compatible with Hitec and JR radio control systems. This item is also available for Futaba and
Airtronics radio control systems. The Wattage IC-15A Micro ESC is compatible with Futaba, JR, Hitec, Airtronics-Z and others.
When you purchase the Cirrus MRX-4II Micro receiver, you must also purchase a Cirrus brand crystal compatible with the receiver. The crystal
must also be on the same frequency as your transmitter.
QTY. 1
145346
Wattage 370 Power System w/Gear Box and Propeller
QTY. 1
443534
Cirrus MRX-4II Micro Receiver
QTY. 1
4462xx
Cirrus Crystal for MRX-4II Micro Receiver
QTY. 3
444038
Cirrus CS-6.5 Micro Servos
QTY. 1
128484
Wattage IC-15A Micro Electronic Speed Control
QTY. 1
128538
8 Cell 5/4AAA 800mAH NiMH Flight Battery
QTY. 1
145310
Wattage Spinner for 370 Power System
QTY. 1
130108
Wattage PF-12 AC/DC Park Flyer Charger
QTY. 1
444713
Cirrus 12" Servo Extension (Optional)
OUR RECOMMENDATIONS, CONTINUED....
❑ Kwik Bond 5 Minute Epoxy # 887560
❑ Kwik Bond Thin C/A # 887500
❑ Kwik Bond Thick C/A # 887510
❑ Kwik Bond C/A Debonder # 887545
❑ Pacer Formula 560 Canopy Glue # 339176
❑ #0, #1 & #2 Phillips Head Screwdrivers
❑ Wire Cutters
❑ Needle Nose Pliers
❑ Adjustable Wrench
❑ Excel Modeling Knife # 692801
❑ Scissors
❑ Electric or Hand Drill
❑ Assorted Drill Bits
❑ Ernst Airplane Stand # 223977
❑ Ruler
❑ Pencil
❑ Dubro T-Pins # 567677
❑ Builder's Triangle
❑ 220 Grit Sandpaper w/Sanding Block
❑ Masking Tape
❑ Paper Towels
❑ Waxed Paper
❑ Rubbing Alcohol
❑ NHP Epoxy Mixing Sticks # 864204
❑ NHP Epoxy Mixing Cups # 864205
❑ K&S 30 Watt Soldering Iron # 598120
*
❑ Solder
*
❑ Heat-Shrink Tubing (Assorted Sizes)
*
SECTION 2: TOOLS AND SUPPLIES REQUIRED
*
These items may be necessary for the installation of your power system.
The tools and supplies listed below will be necessary to finish the assembly of your new Wattage Super Impress II EP ARF. We
suggest having these items on hand before beginning assembly.
The MRX-4II Micro receiver uses a 50U-compatible
micro crystal, Cirrus P/N 4462XX. XX being the
frequency number of your transmitter (i.e., if your
transmitter is on frequency number 52, the crystal you
would purchase would be P/N 446252).
For Direct Drive Power System, Use:
QTY. 1 131480
Wattage Super 400 Cobalt Motor
QTY. 1 128486
Wattage IC-30A Micro ESC
QTY. 1 128577
Wattage 7 Cell CP1300 NiCD Flight Battery
QTY. 1 608140
APC 7 x 4 Nylon Propeller
QTY. 1 143989
Wattage Red Nylon Spinner for C182 EP