1. DL manuals
  2. Wattstopper
  3. Accessories
  4. CI-355
  5. Installation Instructions Manual

Wattstopper CI-355 Installation Instructions Manual

Manual is about: 360 Passive Infrared Line Voltage Occupancy Sensor with Light Level feature

Summary of CI-355

  • Page 1

    Ci-355 v3 360° passive infrared • line voltage occupancy sensor with light level feature specifications voltages ............................................. 120//230/277/347vac, 50/60hz load ratings @120vac .........................................0-800w ballast/tungsten/led @230vac (single phase)...

  • Page 2: Unit Description

    Call 800.879.8585 for technical support unit description the wattstopper ci-355 360° passive infrared (pir) occupancy sensors turn lighting systems on and off based on occupancy and ambient light levels. The light level feature can be used to keep lights from turning on if the ambient light level is...

  • Page 3: Placement Guidelines

    Visit our website for faqs: www.Wattstopper.Com placement guidelines depending upon obstacles such as furniture or partitions, the area of coverage may be less or more than the sensing distances shown in the coverage pattern. This must be considered when planning the number of sensors and their plac...

  • Page 4: Wiring Directions

    Call 800.879.8585 for technical support wiring directions caution turn power off at the circuit breaker before installing sensors. Single sensor, single load warning: this application does not allow for load to increase. Load switch load hot neutral neutral ground (optional) hot neutral neutral load...

  • Page 5: Mounting The Sensor

    Mounting the sensor using a 4-inch square junction box with double-gang mudring 1. Pull the high voltage wires into the j-box through the conduit knockout. 2. Connect the high voltage wires to the appropriate terminals on the sensor. 3. Align the sensor in the j-box so that the mudring mounting scre...

  • Page 6: Sensor Adjustment

    Call 800.879.8585 for technical support sensor adjustment this unit is pre-set for basic operation as described in this guide. Adjustment is optional. The sensors are factory preset to allow for quick installation in most applications. Verification of proper wiring or coverage, or customizing the se...

  • Page 7: Light Level Feature

    Light level feature the light level feature holds lights off upon initial occupancy if adequate ambient light exists. It will not turn the lights off if they are on. The default setting is for maximum, meaning that even the brightest ambient light will not hold the lights off. Notes on functionality...

  • Page 8: *disabling Light Level

    Call 800.879.8585 for technical support 5. When the led stops flashing, replace the front cover. *disabling light level pressing the pushbutton for 5 seconds or more resets the light to default (maxi- mum). Press and hold the light level button over 5s, the led will be on and then off showing 5s mar...

  • Page 9: Dip Switch Setting

    Dip switch setting the ci-355 has 6 dip switches under the cover. Time delay: switches 1, 2, 3 the sensor will hold the lights on as long as occupancy is detected. The time delay countdown starts when no motion is detected. After no motion is detected for the length of the time delay, the sensor wil...

  • Page 10: Troubleshooting

    Troubleshooting for any unexpected operation 1. Check dip switch settings. 2. Make sure the switches are set according to the defined settings in the dip switch setting chart. Lights do not turn on with occupancy, and the following condition exists: red led does not flash: 1. When power is initially...

  • Page 11

    Unwanted sensor activations (led flashes): improper sensor location or inadequate masking causing detection outside of desired coverage area. 1. The pir sensitivity may be set too high. 2. Sensor located too close to hvac or vav vents with heavy air flow. 3. Check if light level is enabled. • if occ...

  • Page 12: Ordering Information

    Ordering information catalog # description ci-355 passive infrared occupancy sensor, line voltage, 360 o lens, up to 1200 square ft., with light level sensor ci-355-1 passive infrared occupancy sensor, line voltage, 360 o high density/reduced range lens, up to 500 square ft., with light level sensor...