Waveline WL270SAXT Owner's Manual & Assembly Manual - page 10
7.
11. ASSEMBLY OF YOUR CRAFT
1. Lay out boat skin
Laytheboatskinoutflatandpullthetransomuprightasmuchaspossible
2. Partially inflate sides
Yourboathasthreeairchamberswithintheskin.Beforeyouinsertthehosenozzle,makesurethatthe
valvehasbeenprimedbygivingthespringinthecentreaclockwise90ºturnensuringthespringitisatfull
length.
Thisensuresapositivesealoncethechamberisinflated.
Toconnectthepumphosesecurelytothevalve,twistthe
nozzletolockintoplace.Usingthefootpump,inflatethe
frontchamberuntilabout1/2-3/4inflated.
Repeatthisprocessforeachoftheothertwochambersontheboat.
3. Constructing Your Floor
ALUMINIUMFLOOR:Unpackthefloorsectionsandtheflooroutnexttotheboat.Lifttheportsideofthe
boatskinatthebowandinsertthefirstfloorsectionrightintothegroovesbetweenthefloorandthepar-
tiallyinflatedsideoftheboatskin.Thenrepeatforthestarboardside.Makesurebowboardispushedright
intothegroovesandthekeelvalveiseasilyaccessiblethroughtheholeinthefloorsection.Insertthenext
floorsectionaswithbow,assuringitlocksintothebowfloorsection.Insertthelastboardintotheboatat
thesternendfirst,andthemlockintothecentresectionatbefore.Pushtheboardsflatandintothegrooves
betweenthefloorandthesidesoftheboatskin.Pullsidesouttoallowboardstoslidein.Unpackthelocking
bars.Placethefirstlockingbarontheleftsidewiththeinsetsidebarfacingintotheboat.Tipthebarunder
thefloorsotheinsertsectionlocksboardsections2and3together.Repeatforrightlockingbar.
AIRDECKFLOOR:Unrollthefloorandfitthewoodensupportbattenintothepocketprovidedontheun-
dersideoftheairdeck(notapplicabletoWL230RAXS)Putthedeckintoplaceensuringtheinflationvalve
isfacingupwardsandtheholethroughtheairdeckallowsaccesstothekeelinflationvalve(WL270SAXT,
WL290SAXT,WL320SAXTonly)
SLATTEDFLOOR:Ifnotalreadyinplace,inserttheprovidedslatsintothestitchedpocketsontheinsideof
theboatfloor.
4. Fit seat
Makesureyouslideyourseatinplaceandtheninflate.Donotinserttheseatafterinflating.
5. Fully inflate both sides
Insertpumppipeintothebowvalveagain,andfullyinflatethebowoftheboatskin.Repeatforbothsides.
Makesurenottooverinflate.Putcapsontovalvesleavingvalvestobeintheclosedposition.Allthree
compartmentsofyourboatshouldnowbeinflated.
6. Assemble oars
Clipthetwopartoarstogether.Twisttheoarmounts(rowlocks)ontothepadsontheboat.Insertoarinto
rowlock,andsecureintotheoarretainer.
7. Final procedures
Affixtheoutboardbracket(WL230RAXSonly)totherearoftheboat.Keepallaccessoriesawayinasafe
place.
WARNING: DO NOT USE A COMPRESSED AIR SOURCE TO INFLATE YOUR CRAFT.
OVERINFLATION MAY CAUSE SEAMS AND/OR CHAMBERS TO RUPTURE.
CAUTION:
-Ensuretheassemblyareaiscleanandfreeofsharpobjects.
-Checkinflationpressurebeforeeachuse
-Checkthetightnessofthevalveregulary.
Closed Position
Open Position
Valve Stem (Spring)
Valve Cap