Wayne-Dalton 3018 Installation Instructions And Owner's Manual - Warning
please do not return this product to the store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need
You can reach us Toll Free at
1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com
29
primary programming for homelink
®
to the classicdrive
®
I
note: This step can only be done on automobiles equipped with the
HomeLink
®
System.
note: Programming HomeLink
®
requires a Wayne-Dalton
Transmitter that is programmed to the opener (transmitter(s) sup-
plied with the opener, come pre-programmed from the factory). Any
additional transmitter(s) will need to be programmed to the opener, see
page 32.
IMportant: use the programming instructions provided with your
vehicle first. Follow these instructions if the HomeLink
®
unit does not
learn the transmitter, when using the vehicle’s instructions.
note: If Primary Programming does not work then use the Alternate
Procedure on next page.
note: Vehicle may need to be in accessory position when
programming. Check car owner’s manual.
note: HomeLink
®
is a registered trademark of johnson Controls.
programming/training homelink
®
unit
GARAGE DOOR MAy OPERATE DuRING PROGRAMMING. TO AVOID
POSSIBLE SEVERE OR FATAL INjuRy, PLACE THE EMERGENCy
DISCONNECT HANDLE IN THE MANuAL OPERATED POSITION.
1. Pull the manual disconnect to put the opener in the disengaged
position.
2. Verify the HomeLink
®
unit has an empty channel press the desired
HomeLink
®
button and observe the indicator light if it flashes slowly,
the channel is empty and ready for programming. If pressing the
desired channel/button causes the indicator light to blink rapidly, or
come on without blinking this channel is already programmed. you
either need to choose a different channel/button on the HomeLink
®
, or
perform Step 3 below.
3. optIonal – To completely clear all channels on the HomeLink
®
unit, press and hold the two outside buttons on the HomeLink
®
unit
until the HomeLink
®
indicator light begins to flash rapidly (approx. 20
seconds), then release both buttons. (Do not perform this step to train
additional hand-held transmitters.)
note: This operation erases all
previously learned transmitters and you will need to re-teach any other
transmitters to your HomeLink
®
unit.
4. Hold the end of the Wayne-Dalton hand-held transmitter
approximately 1 to 3 inches away from the HomeLink
®
surface keeping
the HomeLink
®
indicator light in view.
5. Press and hold the desired HomeLink
®
channel/button indicator light
should flash slowly (indicating empty channel). Continue holding the
HomeLink
®
button, and press and hold the large button (“u” Models) or
desired button (“A”, “C” or “R” models) on the Wayne-Dalton
transmitter for approximately 3-5 seconds. The HomeLink
®
indicator
light should now blink rapidly, indicating a successful learn operation.
Release both buttons. Verify transmitter has been learned by pressing
the HomeLink
®
button used to learn the transmitter; HomeLink
®
indicator light will come on without flashing or flash rapidly indicating a
successful learn. Proceed to step 6 below.
note: If this procedure is
unsuccessful perform Alternate procedure.
teaching homelink
®
to the opener
6. Press and release the program switch on the opener. The red
program status light on the opener and light will turn on and remain lit
for one minute, indicating that it is ready to learn.
7. Press the HomeLink
®
button used in Step 5 above for 1 to 3
seconds. The program status light and convenience light on the opener
will turn on and off three times indicating a successful learn.
8. Press the HomeLink
®
button once more to operate the door. The
opener will activate and the trolley will travel towards open, the next
activation will cause the trolley to travel to the closed position and
reengage, subsequent operations will move the door.
warnIng
OPERA
TION