WeBoost Drive 4G-X Installation Instructions Manual - page 11
11
ENGLISH
Need help?
www.weboost.com
Customer Support 866-294-1660
Signal Booster Specifications
Drive 4G-X
Product Number
U470010
Model Number
460021
FCC ID
PWO460021
IC
4726A-460021
Connectors
SMA
Antenna Impedance
50 Ohms
Frequency
698-716 MHz, 729-756 MHz, 777-786 MHz, 824-894 MHz,
1850-1995 MHz, 1710-1755 MHz / 2110-2155 Mhz
Passband Gain (typical)
700 MHz
Band 12/17
45 .8
700 MHz
Band 13
46 .8
800 MHz
Band 5
46 .8
1700/2100 MHz
Band 4
45 .2
1900 MHz
Band 2
44 .6
20 dB Bandwidth (MHz)
700 MHz
Band 12/17
700 MHz
Band13
800 MHz
Band 5
1700/2100 MHz
Band 4
1900 MHz
Band 2
Typical
Maximum
30 .6
35 .2
31 .0
35 .2
37 .9
39 .9
79 .2
79 .8
77 .3
83 .2
Power output for single cell
phone (Uplink) dBm
700 MHz
Band 12/17
700 MHz
Band13
800 MHz
Band 5
1700 MHz
Band 4
1900 MHz
Band 2
24 .84
24 .35
23 .4
21 .3
24 .43
Power output for single cell
phone (Downlink) dBm
700 MHz
Band 12/17
700 MHz
Band13
800 MHz
Band 5
2100 MHz
Band 4
1900 MHz
Band 2
2 .87
2 .79
2 .8
2 .0
1 .92
Power output for multiple
received channels
(Uplink) dBm
No. Tones
Maximum Power
700 MHz
Band12/17
700 MHz
Band13
800 MHz
Band 5
1700 MHz
Band 4
1900 MHz
Band 2
2
25 .4
23 .9
22 .9
22 .8
24 .9
3
21 .8
20 .4
19 .4
19 .3
21 .3
4
19 .3
17 .9
16 .9
16 .8
18 .8
5
17 .4
16 .0
15 .0
14 .8
16 .9
6
15 .8
14 .4
13 .4
13 .2
15 .3
Power output for multiple
received channels
(Downlinklink) dBm
Maximum Power
No. Tones
700 MHz
Band12/17
700 MHz
Band13
800 MHz
Band 5
2100 MHz
Band 4
1900 MHz
Band 2
2
4 .8
5 .6
5 .4
6 .3
4 .5
3
1 .3
2 .1
1 .9
2 .8
0 .9
4
-1 .2
-0 .4
-0 .6
0 .3
-1 .6
5
-3 .2
-2 .4
-2 .6
-1 .6
-3 .5
6
-4 .7
-4 .0
-4 .2
-3 .2
-5 .1
Noise Figure
5 dB nominal
Isolation
> 90 dB
Power Requirements
6 V 2 A
Each Signal Booster is individually tested and factory set to ensure FCC compliance . The Signal Booster cannot be adjusted without factory
reprogramming or disabling the hardware . The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage
of authorized frequency bands only . If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected . If a detected
signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on
that band . For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1 minute . After 5 (five) such
automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing
power from the Signal Booster . Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor .
The Manufacturer’s rated output power of this equipment is for single carrier operation . For situations when multiple carrier signals are present, the
rating would have to be reduced by 3 .5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users .
This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device .
This device complies with Part 15 of FCC rules . Operation is subject to two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation . Changes or modifications not
expressly approved by weBoost could void the authority to operate this equipment .
The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met .