Wecan E-STUDIO205L Troubleshooting Manual - Www.Wecan-Eg.Com
32 Abo Haya El Tawhedy,
Aria 7, Nasr City,
CAIRO.
WWW.WECAN-EG.COM
T:+2(02)26711737
T:+2(02)22758997
M:+2(02)01111134509
Messages Displayed on the Touch Panel
When a message appears on the touch panel, see the table below to solve the problem.
Corrective Action
Problem Description
Message
Check the cover on the touch panel
and close it.
The cover indicated by *** is open.
Close *** cover.
Remove the jammed paper following
the guidance
displayed on the touch panel.
P.11 “Clearing a Paper Jam”
Paper jam has occurred inside the
equipment.
Misfeed in ***
Just removing the jammed paper does
not prevent
another paper jam. Be sure to
correctly register the
paper size in the equipment.
P.38 “Clearing paper jams caused
by a wrong
paper size
setting”
Paper jam has occurred because of
the mismatch between the paper size
placed in drawer N and the size
registered for the drawer N in the
equipment.
Check paper size setting on control
panel for drawer N
Wait until the adjustment is completed
and the
message disappears.
The equipment is undergoing
maintenance to keep its imaging
quality.
Wait (Performing Self-check)
Remove the jammed original following
the guidance
on the touch panel.
P.13 “Paper jam in the Reversing
Automatic
Do
cument Feeder (optional) (Lower)”
The original is jammed inside of the
Reversing Automatic Document
Feeder (optional).
Check the original and set it again
Check the direction and the size of the
original and
then replace it on the Reversing
Automatic Document
Feeder. Then reattempt the operation.
The direction or the size of the
original placed on the Reversing
Automatic Document Feeder is
incorrect.
Change the orientation of the original
by 90 degrees
and place it on the original glass.
The orientation of the original placed
on the original glass is incorrect.
Change direction of original
Ask your administrator for details of
setting the limit for
the number of copies
The number of originals to be
scanned has exceeded the limit
specified with the department or user
code during scanning.
Change from this mode
Count over, cannot store anymore
Ask your administrator for details of
setting the limit for
the number of copies
The number of originals to be
scanned has exceeded the limit
specified with the department or user
code during scanning.
Change from this mode
Count over, cannot store anymore
Remove the jammed staples.
P.50 “Staple jam in the saddle
stitch unit”
Staple jam has occurred in the stapler
of the saddle stitch unit
READY (CHECK SADDLE STITCH
STAPLER)
Refill the staples.
P.66 “Refilling saddle stitch unit
staples”
No staples are left in the stapler of the
saddle stitch unit.
READY (CHECK SADDLE STITCH
STAPLER)
Remove the jammed staples.
P.43 “Clearing a Staple Jam”
Staple jam has occurred in the stapler
of the finisher.
READY (CHECK STAPLER)
Refill the staples.
P.59 “Refilling With Staples
No staples are left in the stapler of the
finisher.
READY (CHECK STAPLER)
Install the toner cartridge correctly.
P.53 “Replacing a Toner Cartridge”
The toner cartridge is not installed. Or
it is not installed correctly
READY (TONER NOT
RECOGNIZED
Use a TOSHIBA-recommended toner
cartridge.
P.53 “Replacing a Toner Cartridge”
A toner cartridge not recommended
by TOSHIBA is being used.
Remove the paper punchings.
P.70 “Cleaning the Hole Punch
Dust Bin” READY (INNER TRAY FULL)
Hole punch dust bin is full of paper
punchings.
READY (HOLE PUNCH DUST BIN IS
FULL)