Weider powerguide x2 User Manual

Page of 12

Download

Print this page

Bookmark us

USER’S MANUAL

home gym s

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete cus-

tomer satisfaction. If you have

questions, or find that there are

missing or damaged parts, we

will guarantee complete satisfac-

tion through our Customer

Service Department.

Please CALL:

0345-089009

or WRITE:

ICON Lifestyle Ltd

Greenwich House

223 North Street

Sheepscar

Leeds LS7 2AA

West Yorkshire

Model No. X2-1

Serial No.

Serial Number Decal (Under Seat)

ORDERING REPLACEMENT PARTS

To order replacement parts, write or call:

Consumer Products Distribution

Greenwich House

223 North Street

Sheepscar

Leeds LS7 2AA

West Yorkshire

Tel: Country Code: 0345-089009

Fax: 0113-2411120

To help us assist you, please be prepared to give the following information:

• The MODEL NUMBER of the product (X2-1).

• The NAME of the product (WEIDER

POWERGUIDE X2 HOME GYM SYSTEM).

• The SERIAL NUMBER of the product (see the front cover of this manual).

• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on page 18 of this user’s manual).

Part No. 123331 R0497A

CAUTION

Read all precautions and instruc-

tions in this user’s manual

before using this equipment.

Save this user’s manual for

future reference.

1 2 3 4 5 6 7 Next › »

Summary of powerguide x2

Page 1
User’s manual home gym s home gym s questions? As a manufacturer, we are com- mitted to providing complete cus- tomer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee complete satisfac- tion through our customer service department. Please call: ...
Page 2
Exploded drawing—model no. X2-1 r0497a 2 table of contents important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 3
18 part list—model no. X2-1 r0497a note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key no. Qty. Description 1 14 5/16” nylon locknut 2 5 3/8” nylon locknut 3 2 1/4” nylon locknut 4 10 3 1/2” thin pulley 5 10 5/16” flat washer 6 2 1/4” flat washer 7 1 ...
Page 4
17 cable diagrams the diagrams below show the proper routing of the low cable (70) and the high cable (71). Use the diagrams to make sure that the two cables are assembled correctly. The numbers show the routing of the cables from the starting to ending points. 4 5 6 7 low cable (70) 2 1—low pulley ...
Page 5
16 trouble-shooting and maintenance inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. How to tighten the cables woven cable, the type of ...
Page 6
15 attaching the leg lever to the low pulley station to use the leg lever (20), the seat must be attached to the front upright (see attaching and remov- ing the seat on page 14). Attach the chain (58) between the low cable (70) and the 5/16” x 2” eye bolt (21) with two cable clips (57). Attaching th...
Page 7
14 adjustment the instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise chart accompanying this user’s manual to see how the home gym system should be set up for each exercise. Important: when attaching the lat bar or nylon strap, make sure that the ...
Page 8
13 29. Before using the home gym system, tighten the cables (see how to tighten the cables on page 16 of this user’s manual). In addition, pull each cable a few times to make sure that the cables move smoothly over the pulleys. If the cables do not move smoothly, locate and correct the problem befor...
Page 9
25 26 27 28 81 19 18 72 41 22 20 23 23 15 10 10 14 pins 18 41 60 27 27 16 6 lubricate—80 20 5 1 21 12 25. Press a 1 1/2” inner cap (19) into the leg lever (20). Lubricate a 5/16” x 2 1/4” bolt (80). Attach the leg lever (20) to the seat frame (18) with the bolt and a 5/16” jam nut (81). Do not overt...
Page 10
10 18. Route the low cable (70) on the indicated side of the “v” brace (42). Route the low cable into the groove in a 3 1/2” thin pulley (4). Attach th epulley an d a cable trap (69) to the large pivot bracket (52) with a 3/8” x 1 3/4” bolt (68) and a 3/8” jam nut (82). Be sure the cable trap is in ...
Page 11
1” round cover cap (30)–2 4” weight pin (50)–1 plastic bushing (79)–2 4 1/2” “l” pin (61)–2 5/16” knob (15)–1 “j” pin (56)–1 this chart is provided to help you identify the small parts used in assembly. Note: some parts may have been pre- assembled for shipping purposes; if you cannot find a part in...
Page 12
Part identification chart—model no. X2-1 r0197a this chart is provided to help you identify the small parts used in assembly. The number in parenthesis below each part refers to the key number of the part. The second number refers to the quantity used in assembly. 1/4” jam nut (75)–4 1/4” nylon lock...