1. DL manuals
  2. Worcester
  3. Thermostat
  4. DT10RF
  5. Instruction manual

Worcester DT10RF Instruction manual

Other manuals for DT10RF: Operating And Installation
Manual is about: Digital Wireless Thermostat

Summary of DT10RF

  • Page 1

    Dt10rf programmer digistat - radio frequency controlled programmable room thermostat with domestic hot water programmer for greenstar cdi, greenstar i junior and greenstar si models also greenstar i system and greenstar cdi system (only when used in conjunction with optional integral diverter valve ...

  • Page 2

    For latest prices and delivery to your door visit mytub ltd - www.Mytub.Co.Uk - info@mytub.Co.Uk 0844 556 1818.

  • Page 3

    Worcester, bosch group: technical 08705 266241 service 08547 256206 spares 01905 752571 literature 01905 752556 training 01905 752526 sales 01905 752640 website worcester-bosch.Co.Uk symbols domestic hot water radio frequency (rf) transmitter please read these instructions carefully before starting ...

  • Page 4

    Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 digistat transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 general information . . . . . . . . . . . . . . . . . . . . . . . . . . .2 programmable thermostats . . . . . . . . ...

  • Page 5

    Ec directives: european union law directive 2000/84/ec low voltage directive (2006/95/ec) electro-magnetic compatibility directive (89/336/eec) ec marking directive (93/68/eec) standard package: programmable / rf receiver remote rf transmitter screws (x2) wall plugs (x2) instructions batteries (x2) ...

  • Page 6

    What is a programmable room thermostat? A programmable room thermostat is both a pro- grammer and a room thermostat. A programmer allows you to set ‘on’ and ‘off’ time periods to suit your own lifestyle. A room thermostat works by sensing the air tem- perature, switching on the heating when the air ...

  • Page 7

    General information operating controls dt10rf pro grammer instruction manual 8 716 114 477a (08.07) oper at ing & insta l l at ion inst ruct ions 3 days temperature see note + or - buttons for setting adjustment clock mode right hand button > moves the pointer to the right, selects and accepts chang...

  • Page 8

    Digistat pre-programmed settings oper at ing & insta l l at ion inst ruct ions 4 the digistat programmer this is a programmable thermostat 24-hour product (the same program for every day of the week) which allows you to set up to 6 time and temperature events per day. Pre-set program 1 the following...

  • Page 9

    Programmable settings adjusting times & temperatures dt10rf programmer instruction manual 8 716 114 477a (08.07) oper at ing & insta l l at ion inst ruct ions 5 to change temperature for a short period (override): 1. Press + or - buttons to adjust set temperature. Set temperature shown flashing 2. A...

  • Page 10

    Digistat user options user options user options (shown in table below) can be accessed from auto or man by pressing simultaneously for 3 seconds. Once you have accessed the user options menu press > to scroll through selectable options. The settings for each option can be changed by pressing + or - ...

  • Page 11

    Pre-set program 3 (home worker) 24 hours as you can see, at 06:00, the heating will come on to raise the temperature to 21°c. At 08:30, the temperature set point is dropped to 19°c, it stays at 19°c until 12:00 when the heating comes on to raise the temperature to 21°c. The tem- perature stays at 21...

  • Page 12

    Note: option 5 must be completed before attempting option 6 option 06 how to change temperature offset. The temperature displayed on the thermostat may not match that of other temperature measuring devices in the controlled space, because of its location. The displayed temperature may be offset to b...

  • Page 13

    Mode indicator hot water pre- heat on light hot water pre-heat select button, moves the pointer up and down to select and accept changes hot water pre- heat advance button, when pressed stays on until next off period. Press to accept each program setting setting clock, date, time, program and holida...

  • Page 14

    Hot water: 1. Press select button to choose off = constantly off timed = up to 3 on and 3 off time periods as program once = on from first on until third off time period as program on = constantly on 2. Press “advance” button: on = hot water pre-heat light on (hot water pre-heat stays on until next ...

  • Page 15

    Note: the on/off periods pre-programmed for hot water pre-heat are shown in the table opposite. The factory installed settings can be used without any further programming of the receiver. The date and time are pre-programmed and should not require adjustment. If you need to restore the factory pre-s...

  • Page 16

    Dt10rf receiver programmable settings setting mon - fri 1. Press set? Until set and prog? Are shown in the display. 2. Press ok to select mon-fri. 3. Press ok to select on time. Note: speed up the display by holding down the + or - buttons. 4. Press + or - to change the on time. 5. Press set? To set...

  • Page 17

    Setting individual weekdays: note: if you do not require individual weekday times, then press set? Until set sun-sat is displayed and continue on the next page. If you do not wish to change the setting for the day displayed, then press set? Until the first day you want to change is displayed. 1. Pre...

  • Page 18

    Setting sat - sun: 1. Press ok to select weekend. Note: speed up the display by holding down the + or - buttons. 2. Press + or - to change the on time. 3. Press set? To set the on time and select the off time. 4. Press + or - to change the off time. 5. Press set? To set the off time and select the n...

  • Page 19

    Setting individual weekend days: note: if you do not require individual weekend times, then press set? Until the normal dis- play is shown. If you do not wish to change the setting for sat, then press set? Until the normal display is shown. 1. Press ok to select the day displayed. Note: speed up the...

  • Page 20

    Setting the clock and time 1. Press the set? Button until set and clock are displayed. 2. Press ok. 3. Press + to switch between 24hr and 12hr display. 4. Press set? To set the clock and the hours display flashes. 5. Press + or - to set the correct hour. Note: speed up the display by holding down th...

  • Page 21

    Setting the date note: if the day displayed is incorrect, the date needs resetting as follows: 1. Press the set? Button until set and date are displayed. 2. Press the ok button once, the year will flash on the display. 3. Press + or - to correct the year. 4. Press the set? Button and the month will ...

  • Page 22

    Dt10rf receiver installation danger: 230 volts do not touch the electrical components or circuits caution: isolate the mains electricity supply before starting any work and observe all relevant safety precautions 1. Remove the boiler outer casing and control panel fascia to gain access to the heatro...

  • Page 23

    1. Remove the front cover using a flat screwdriver and separate from back plate. 2. Fix the back plate directly onto the wall using suit- able wall plugs and screws. 3. Replace the front cover by locating in position and pushing fully onto the back cover. Mounting the digistat location the digistat ...

  • Page 24

    Receiver set up: after initial start up, the colon, ch and antenna symbols should be flashing on the display. 1. Press the set? Button 4 times 2. Press the ok button once 3. Press the set? Button 4 times; lrn and off should be displayed 4. Press the + button so the display shows on and a flashing an...

  • Page 25

    Installer options if you wish to change any of the installer options as shown below, enter the installer option menu from auto mode by pressing seconds. Pressing menu and return to auto mode. Once the installer options screen has been selected, the buttons allow you to scroll through the menu (shown...

  • Page 26

    Option 10 - system protection in some heating systems there may be a requirement to protect the system by operating it once a day, for a given period. If system protection is selected the system will be operated for a period as shown in system protection time (mins). System protection time is every ...

  • Page 27

    Maintenance: the transmitter (digistat programmer or optimising programmer) requires no maintenance. The outer casing can be wiped clean using a dry cloth. Do not use polish or detergents. These units can not be serviced. Should the existing unit fail to function correctly, check: receiver times and...

  • Page 28

    O per at ing and ins ta ll ation ins t ru ct i o ns worcester, bosch group cotswold way, warndon, worcester wr4 9sw. Tel. 01905 754624 fax. 01905 754619 www.Worcester-bosch.Co.Uk worcester bosch group is a trading name of bbt thermotechnology uk ltd. 8 716 114 477a (08.07) 06515043001 contact inform...