- DL manuals
- Xact
- Cell Phone
- X33X
- Instruction Manual
Xact X33X Instruction Manual
Summary of X33X
Page 1
Please log on to www.Getxact.Com for accessory & product information. X33x owner’s manual (rev3).Qxd 7/16/2003 9:57 am page 1.
Page 2
Special features congratulations! You now own a quality xact tm communication product. If you follow the set-up, operation and care instructions in this owner’s manual, this unit will provide you with years of trouble-free service. Xact is committed to providing quality products that fit your needs....
Page 3
Communicator controls lcd screen 1. Channel number (1~22) – changes from 1-22 as selected by user. 2. Transmit indicator (tx) – indicates unit is transmitting a signal. 3. Receive indicator (rx) – indicates unit is receiving a transmission. 4. Call tone transmission (call) – indicates the unit is pa...
Page 4
Fcc notice this device complies with part 15 of fcc regulations. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesired operation. Important: changes or m...
Page 5
Fcc notice safety information your wireless hand-held portable transceiver contains a low power transmitter. When the push-to-talk (ptt/call) button is pushed it sends out radio frequency (rf) signals. This devise is authorized to operate at a duty factor not to exceed 50%. In august 1996, the feder...
Page 6
Getting started battery installation: your x33x communicator is powered by a lithium-ion battery (included). To install and replace the battery : 1. Release the battery compartment cover latch located on the rear side of the unit, and remove the cover from the battery compartment. 2. Install the lit...
Page 7
Headset/charger jack cover getting started charging the battery: your x33x communicator comes with an a/c adapter charger to charge your lithium-ion battery. To charge: 1. Lift the headset/charger jack cover located on the side of your communicator. 2. Connect the a/c adapter charger into an a/c wal...
Page 8
Getting started battery level and low battery operation in watch and communicator mode the low battery level icon will not appear on the display unless the unit detects that the battery level is low. The unit has a low battery level icon which will blink when it detects a low battery level in commun...
Page 9
Getting started adjusting the watch band: your x33x communicator is designed with a simple release button making it easy to remove it from your wrist. 1. Adjust the watch band on your x33x communicator until it is comfortable, by inserting the two metal studs of the strap into the appropriate holes....
Page 10
Operation 1. Installing the battery turns-on the communicator and activates watch mode. 2. Enter communicator mode by pressing and holding the power button for 3 seconds. To exit communicator mode, press the power button for 3 seconds. 3. Check for the low battery level icon on the lcd screen. 4. Ad...
Page 11
Operation watch mode: the x33x communicator functions as a digital watch while in this mode. 1. Install the battery and the communicator's lcd screen will display the time in the watch mode. 2. Press the menu button until a "beep" is heard and the displayed hour will "flash". Press the up or down bu...
Page 12
Operation communicator mode: the x33x communicator functions as a two-way communication device while in this mode. 1. Press the menu button for 3 seconds and a short "beep" followed by a long "beep" will be heard, the communicator's lcd screen will quickly display all of the communicator's status ic...
Page 13
Operation changing channels: the x33x communicator has 22 channels for communicating with others. To change the communicator's channels while in communicator mode: 1. Enter communicator mode by pressing the menu button for 3 seconds and a short "beep" followed by a long "beep" will be heard, the com...
Page 14
13 operation note: selecting a ctcss code of “of” will disable the ctcss feature. In order for other people to receive your transmission, they must be on the same channel and ctcss code you are currently using. Adjusting speaker volume (standby/receive mode): 1. Press the up button to increase the s...
Page 15
Operation transmitting and receiving a signal: the communicator is continuously in receive/standby mode when the unit is on, in communicator mode, and not transmitting. Changing the position of the communicator (or its antenna) may increase the quality and range of the communicator's transmitted or ...
Page 16
Operation for greater privacy and convenience of hands-free transmission, use an ear bud (headset) with microphone (see accessory order form) when using vox mode. Connecting the ear bud (headset): 1. Set the communicator to vox mode. 2. Lift the headset/charger jack cover located on the side of the ...
Page 17
Troubleshooting problem solution no power • check the battery. Ensure that the battery is installed properly. • battery may be weak. • recharge your battery by using the a/c adapter charger. • your battery may be damaged. Replace old battery with a new lithium-ion battery. Weak reception • press the...
Page 18
Troubleshooting problem solution range is limited • battery may be weak. • recharge battery if the battery level indicator is low. • range varies depending on terrain and environment. • open fields provide maximum range; steel/concrete structures, heavy foliage, and operation in buildings and in veh...
Page 19
Specifications channels available 22 frs/gmrs channels and 38 ctcss codes operating frequency uhf 462.5500 - 467.7125 mhz power source 3.7v lithium-ion battery (xb10) output power (tx) 0.3w erp maximum battery life varies per user range about 1.5 miles channel (mhz) and ctcss code (hz) frequency cha...
Page 20
Care and maintenance damaged antenna: do not use any communicator that has a damaged antenna. If a damaged antenna comes in contact with the skin, a minor burn may occur. Important battery information: only use the battery indicated in this manual. Using another type of battery may substantially red...
Page 21
Warranty xact communication one-year limited warranty this limited warranty sets forth all xact communication responsibilities as they apply to your x33x communicator. There are no other expressed or implied warranties from xact communication. Warranty service provided if you purchased the x33x comm...
Page 22
Warranty what to do for warranty service during the first thirty (30) days, a defective product is eligible for over-the-counter exchange at the retailer from whom it was purchased. After thirty (30) days, the defective product should be returned to the authorized service center. The shipping addres...
Page 23
Warranty for your reference: model number __________________________________________________ date of purchase ________________________________________________ name of dealer _________________________________________________ toll free customer service telephone number 1-866-466-xact (9228) 22 before ...
Page 24
Styled for life www.Getxact.Com made in china bn x33x owner’s manual (rev3).Qxd 7/16/2003 9:58 am page 24.