1. DL manuals
  2. Xantrex
  3. Power Supply
  4. XPower 300
  5. Owner's Manual

Xantrex XPower 300 Owner's Manual

Other manuals for XPower 300: Owner's Manual, Owner's Manual, Owner's Manual

Summary of XPower 300

  • Page 1

    By xpower inverter 300 owner’s guide.

  • Page 2: About Xantrex

    About xantrex xantrex technology inc. Is a world-leading supplier of advanced power electronics and controls with products from 50 watt mobile units to one mw utility-scale systems for wind, solar, batteries, fuel cells, microturbines, and backup power applications in both grid-connected and stand-a...

  • Page 3: Table of Contents

    Iii 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. Important safety information . . . . . . . . . . . . . . . . . . 2 warnings and cautions . . . . . . . . . . . . . . . . . . . . . . . . 2 3. Xpower 300 inverter features . . . . . . . . . . . . . . . . . . 6 ...

  • Page 4

    Iv.

  • Page 5: 1 Introduction

    1 1 introduction thank you for purchasing the xpower inverter 300 . The xpower 300 is part of a family of advanced, high- performance power inverters from xantrex, the leader in the field of high-frequency inverter design. Connected to the 12 volt outlet in your vehicle or directly to your battery f...

  • Page 6: Warning Statements Identify

    2 2 important safety information if the xpower 300 is connected or used incorrectly, hazardous conditions may be created. Read and save this safety information, and pay special attention to all caution and warning statements in the guide and on the inverter itself. Warnings and cautions are indicate...

  • Page 7: Warning: Fire Hazard

    3 warning: risk of fire or explosion the xpower 300 contains components that tend to produce arcs or sparks. To prevent fire or explosion, do not install the inverter in compartments containing batteries or flammable materials or in locations that require ignition- protected equipment. Warning: fire...

  • Page 8: 300

    4 caution: risk of damage to equipment the xpower 300 is designed to be directly connected to standard electrical and electronic equipment in the manner described in this guide. Do not connect it to household or rv ac distribution wiring. Do not connect it to any ac load circuit in which the neutral...

  • Page 9: Appliances

    5 caution: risk of damage to rechargeable appliances the output of the xpower 300 is non-sinusoidal. Certain battery chargers can be damaged if they are connected to the xpower 300. Two particular types of equipment are prone to this problem: • small battery-operated appliances such as rechargeable ...

  • Page 10

    6 3 xpower 300 inverter features this section describes the main features of the xpower 300. Figure 1 shows the inverter’s ac panel. Figure 1 ac panel on the xpower 300 (european ac outlet) ➀ ac outlet an ac outlet is located on one end of the inverter. It allows you to plug in a 230 volt ac product...

  • Page 11: Power Light The Green

    7 when the inverter is connected to a dc power source and the on/standby switch is on, ac power is available at the outlet. ➂ power light the green pwr light is on all the time when the on/standby switch is on. ➃ fault light the red light indicates that the inverter has shut down because of low or h...

  • Page 12: Ac Outlets

    8 ac outlets depending on your geographic location, your xpower 300 will have one of the following ac outlets. Figure 2 european ac outlet figure 3 british ac outlet figure 4 australian and new zealand ac outlet.

  • Page 13: 4 Connecting The Xpower 300

    9 4 connecting the xpower 300 this section explains how to connect the xpower 300. Choosing a location for the best performance, choose a location that is: • dry do not expose the inverter to water drip or spray. • cool operate the inverter in ambient temperatures between 0° c and 40° c (32° f and 1...

  • Page 14: 300

    10 connecting the xpower 300 to dc power you can connect the inverter to a 12 volt dc power source using: • the cigarette plug wire assembly (page 11) • the battery clip wire assembly (page 12) • a hardwired connection to the battery (page 14) your method will depend on the size of the ac loads you ...

  • Page 15: Warning: Fire Hazard

    11 using the cigarette plug wire assembly loads under 150 watts when you are going to power loads under 150 watts, use the cigarette plug wire assembly. To connect the inverter: 1. Remove the nuts from the dc terminals on the inverter. 2. Place the red ring connector on the inverter’s red (positive ...

  • Page 16: Hazard

    12 5. Turn on the inverter’s on/standby switch. The pwr light comes on, and ac power is available at the outlet. Note: you may need to turn the vehicle’s ignition key to the accessory position. 6. Plug in the ac load you want to operate. Using the battery clip wire assembly loads greater than 150 wa...

  • Page 17: 300

    13 to connect the inverter: 1. Remove the nuts from the dc terminals on the inverter. 2. Place the red ring connector on the red (positive +) dc terminal, and then screw the red nut on until it is snug. Do not over tighten. 3. Attach the red clip to the red (positive +) battery terminal. 4. Attach t...

  • Page 18: –

    14 7. Turn on the on/standby switch. The green pwr light comes on, and ac power is available at the outlet. Hardwiring the inverter to the battery loads of any size (up to 300 watts continuous power) for a permanent electrical connection, or when you need to power some loads that are greater than 15...

  • Page 19: Warning: Fire Hazard

    15 warning: fire hazard the wires in most 12 volt sockets or power outlets are not large enough for loads greater than 150 watts: they will overheat and present a fire hazard. For loads greater than 150 watts, connect the inverter directly to the battery and use appropriately sized wires like those ...

  • Page 20

    16 to hardwire the inverter to the battery: 1. Cut the clips off the cable clip wire assembly. (the wires in this assembly are appropriate for loads over 150 watts. The wires in the cigarette plug wire assembly are too small: do not use them.) 2. Using 3.3mm 2 (12 awg) wire or heavier, extend the po...

  • Page 21: 300

    17 6. Remove the nuts from the dc terminals of the inverter. 7. Place the red ring connector on the red (positive +) dc terminal on the inverter, and then screw the red nut on until it is snug. Do not over tighten. 8. Fasten the positive terminal (red wire) to the positive battery post. 9. Fasten th...

  • Page 22: Disconnecting The Battery

    18 disconnecting the battery • before you disconnect the battery, turn off the ac load, and then turn off the in-line switch. Replacing the in-line fuse • if you need to replace the in-line fuse (see figure 6), turn off the in-line switch to disconnect the dc power..

  • Page 23: 5 Operating The Xpower 300

    19 5 operating the xpower 300 this section describes normal operation as well as several problems that could occur when you use the inverter. If you have a problem, see “troubleshooting” on page 23. Operating statuses • normal operation when you connect the inverter to your vehicle’s 12 volt source ...

  • Page 24

    20 that occurs when the engine starts may trigger a low voltage shutdown. • ac overload shutdown if you connect an ac load rated higher than 300 watts or 1.3 amps or that draws excessive surge power, the xpower 300 shuts down. The pwr light stays on, and the light comes on to indicate that the inver...

  • Page 25

    21 interference with electronic equipment most ac products operate with the xpower 300 as they would with household ac power with the following exceptions. Buzzing sound some inexpensive stereo systems and “boom boxes” have inadequate internal power supply filtering and buzz slightly when powered by...

  • Page 26: 6 Battery Operating Time

    22 6 battery operating time the battery operating time of the xpower 300 depends on the charge level of the battery, battery capacity, and the amount of power drawn by the particular ac load. With a typical vehicle battery and a 300 watt load, you can expect one or more hours of operating time. To p...

  • Page 27: 7 Troubleshooting

    23 7 troubleshooting this section describes problems you may encounter, the symptoms of each problem, possible causes, and various remedies. The ac load will not operate; the red light is on. Symptom an ac load is plugged in or turned on, operates for one to ten seconds, and then shuts down. Warning...

  • Page 28: Possible Cause

    24 symptom the ac load does not operate. The light comes on when the inverter is turned on or when the ac load is turned on or plugged in. The alarm may sound. Symptom the ac load runs for more than one minute, the alarm sounds, and the light comes on. The inverter is warm or hot to touch. The alarm...

  • Page 29: Possible Cause

    25 the ac load will not operate; no inverter lights are on. Symptom the cigarette lighter works in the lighter socket, but the inverter does not. Symptom the cigarette lighter does not work in the lighter socket. Possible cause suggested remedy the contact between the plug and the lighter socket or ...

  • Page 30: Possible Cause

    26 measured inverter output voltage is too low. Symptom the ac voltmeter reading is 5 to 15 volts too low. Battery operating time is less than expected. Symptom the inverter runs for a while, and then the light comes on. The inverter is cool or warm to touch. Possible cause suggested remedy a standa...

  • Page 31: 8 Specifications

    27 8 specifications specifications may change without notice. Electrical ac receptacles 1 ac output voltage 230 volts ac rms ± 5% ac output frequency 50 ± 3 hz ac output waveform modified sine wave maximum continuous ac output power 300 watts maximum ac output surge power 600 watts dc input voltage ...

  • Page 32: Physical

    28 physical regulatory dimensions (l x w x h) 200mm x 103mm x 66mm (7.9 in. X 4.1 in. X 2.6 in.) weight 0.79 kg (1.74 lb.) ce mark low voltage directive e mark automotive emc directive tuv/type approved certified to en60950

  • Page 33: 9 Limited Warranty

    29 9 limited warranty warranty what does this warranty cover? This limited warranty is provided by xantrex technology, inc. ("xantrex") and covers defects in workmanship and materials in your xpower inverter 300. This warranty period lasts for twenty-four (24) months from the date of purchase at the...

  • Page 34

    30 how do you get service? If your product requires troubleshooting or warranty service, contact your merchant. If you are unable to contact your merchant, or the merchant is unable to provide service, contact xantrex directly at: direct returns may be performed according to the xantrex return mater...

  • Page 35: Disclaimer

    31 what does this warranty not cover? This limited warranty does not cover normal wear and tear of the product or costs related to the removal, installation, or troubleshooting of the customer's electrical systems. This warranty does not apply to and xantrex will not be responsible for any defect in...

  • Page 36: Exclusions

    32 restriction any implied warranty or condition of quality, merchantability or fitness for a particular purpose. Any implied warranty of merchantability or fitness for a particular purpose to the extent required under applicable law to apply to the product shall be limited in duration to the period...

  • Page 37: Warning: Limitations On Use

    33 warning: limitations on use please refer to your product manual for limitations on uses of the product. Specifically, please note that the xp ower i nverter 300 should not be used in connection with life support systems or other medical equipment or devices. Without limiting the generality of the...

  • Page 38: Return Procedure

    34 return procedure 1. Package the unit safely, preferably using the original box and packing materials. Please ensure that your product is shipped fully insured in the original packaging or equivalent. This warranty will not apply where the product is damaged due to improper packaging. 2. Include t...

  • Page 39: Out of Warranty Service

    35 out of warranty service if the warranty period for your xpower inverter 300 has expired, if the unit was damaged by misuse or incorrect installation, if other conditions of the warranty have not been met, or if no dated proof of purchase is available, your inverter may be serviced or replaced for...

  • Page 40

    36.