1. DL manuals
  2. Xerox
  3. Printer
  4. DocuPrint 4850 IPS
  5. Message Manual

Xerox DocuPrint 4850 IPS Message Manual

Manual is about: Xerox 4850: User Guide

Summary of DocuPrint 4850 IPS

  • Page 1

    Xerox docuprint ips messages guide version 7.1 august 2000 721p88950

  • Page 2

    Xerox corporation printing systems documentation and education 701 south aviation boulevard, esm1-058 el segundo, ca 90245 ©1997, 1998, 1999, 2000 by xerox corporation. All rights reserved. Copyright protection claimed includes all forms and matters of copyrightable material and information now allo...

  • Page 3

    Xerox docuprint ips messages guide iii laser safety ! Warning: adjustments, use of controls, or performance of procedures other than those specified herein may result in hazardous light exposure. The xerox docuprint printers are certified to comply with the performance standards of the u.S. Departme...

  • Page 4

    Iv xerox docuprint ips messages guide operation safety your xerox equipment and supplies have been designed and tested to meet strict safety requirements. They have been approved by safety agencies, and they comply with environmental standards. Please observe the following precautions to ensure your...

  • Page 5: Table Of Contents

    Xerox docuprint ips messages guide v table of contents laser safety iii ozone information iii operation safety iv introduction vii about this guide vii contents vii conventions viii related publications ix 1. Hcu messages 1-1 2. Docuprint 96/4635/180 ips messages 2-1 printer control console messages...

  • Page 6

    Table of contents vi xerox docuprint ips messages guide.

  • Page 7: Introduction

    Xerox docuprint ips messages guide vii introduction the xerox docuprint ips messages guide contains the messages you may encounter while using your xerox docuprint ips. About this guide this guide is intended to assist you in dealing with the software, hardware and system errors that may occur while...

  • Page 8

    Introduction viii xerox docuprint ips messages guide conventions the following conventions are used in this guide: “overview” references to chapters, sections, and appendices appear in quotations marks. Messages guide names of documents and documentation libraries appear in italics. “setup” informat...

  • Page 9

    Introduction xerox docuprint ips messages guide ix related publications this document is part of the xerox docuprint ips publication set. Xerox documents following is a list of all xerox docuprint ips documents. For a complete list and description of available xerox documentation, refer to the xerox...

  • Page 10

    Introduction x xerox docuprint ips messages guide.

  • Page 11: Hcu Messages

    Xerox docuprint ips messages guide 1-1 1. 1 hcu messages the messages discussed in this chapter are represented by code numbers displayed in the led panel on the front of the host channel unit (hcu). Note: the information in this chapter applies only to ips with a channel attachment, which requires ...

  • Page 12

    Hcu messages 1-2 xerox docuprint ips messages guide code definitions the following tables give the meaning of the led codes that may appear on the hcu. Table 1-1. Software states (no decimal point) code meaning 9 checking sram 8 loading microcode and startup 7 checking channel interface 6 waiting fo...

  • Page 13: Docuprint 96/4635/180 Ips

    Xerox docuprint ips messages guide 2-1 2. 2 docuprint 96/4635/180 ips messages this chapter contains a list, in numerical order by code, of the messages that you may encounter while using your xerox docuprint 96, 4635, or 180 ips. It also discusses the different kinds of messages and other informati...

  • Page 14

    Docuprint 96/4635/180 ips messages 2-2 xerox docuprint ips messages guide figure 2-1. Printer control console 1 language icon 2 printer icon 3 fault list icon 4 tools icon 5 guarded tools icon 6 clear button 7 continue button 8 stop button 9 sample button 10 brightness control thumbwheel 11 icon are...

  • Page 15

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-3 4. Tools icon select this icon to display call for service information and to adjust display features of the printer control console (for example, alarm volume). 5. Guarded tools icon this icon is reserved for the service repr...

  • Page 16

    Docuprint 96/4635/180 ips messages 2-4 xerox docuprint ips messages guide message list note: throughout the messages in this section, ‘%s’ denotes a file name that is supplied by the system when the message is displayed. 01-210 printer left door open in print. The left printer door is open while the...

  • Page 17

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-5 03-202 edn comm problem with the uim the edn cannot communicate with the uim. Action select the fault list icon on the printer control console touch screen. Then touch the [clear] button to clear the codes. If the error persis...

  • Page 18

    Docuprint 96/4635/180 ips messages 2-6 xerox docuprint ips messages guide 03-223 cp-iop unable to com with touch screen. The cp-iop psb cannot communicate with the touch screen board. Action select the fault list icon on the printer control console touch screen. Then touch the [clear] button to clea...

  • Page 19

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-7 03-245 phn dio 5 is offline. The phn core cannot communicate with phn dio board 5. Action select the fault list icon on the printer control console touch screen. Then touch the [clear] button to clear the codes. If the error p...

  • Page 20

    Docuprint 96/4635/180 ips messages 2-8 xerox docuprint ips messages guide 03-255 fsn1 dio 1b is offline. The fsn core cannot communicate with fsn dio dio board 1b. Action select the fault list icon on the printer control console touch screen. Then touch the [clear] button to clear the codes. If the ...

  • Page 21

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-9 03-343 ros expos$ref turnaround failure. The min slb/rdr board to raster output scanner (ros) turnaround test failed. Action select the fault list icon on the printer control console touch screen. Then touch the [clear] button...

  • Page 22

    Docuprint 96/4635/180 ips messages 2-10 xerox docuprint ips messages guide 03-372 uim needs softwreset hardwcaused. Uim core board detected a potential hardware problem that required a software reset. Action press the [clear] or [reset] button located behind the printer control console front pull-do...

  • Page 23

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-11 03-380 uim boot rom download failure. The uim core boot rom download failed. Action no action required. 03-381 edn download failure. The edn core board download failed. Action no action required. 03-382 uim download failure. ...

  • Page 24

    Docuprint 96/4635/180 ips messages 2-12 xerox docuprint ips messages guide 03-390 uim rigid disk fault. A rigid disk failure was detected by the uim core board. Action select the fault list icon on the printer control console touch screen. Then touch the [clear] button to clear the codes. 03-391 uim...

  • Page 25

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-13 03-404 system comm problem with phn. The system is unable to communicate with the phn. Action select the fault list icon on the printer control console touch screen. Then touch the [clear] button to clear the codes. If the er...

  • Page 26

    Docuprint 96/4635/180 ips messages 2-14 xerox docuprint ips messages guide 03-416 fsn2 can’t talk to any node on bus. The fsn core board 2 cannot communicate with any board on the local bus. Action select the fault list icon on the printer control console touch screen. Then touch the [clear] button ...

  • Page 27

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-15 03-471 edn problem needs software reset. A potential hardware or software problem detected on the edn core board required a software reset. Action select the fault list icon on the printer control console touch screen. Then t...

  • Page 28

    Docuprint 96/4635/180 ips messages 2-16 xerox docuprint ips messages guide 03-482 edn unexpected stacker signal. The job manager received an unexpected delivery signal and initiated a cycle down of the printer. Action select the fault list icon on the printer control console touch screen. Then touch...

  • Page 29

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-17 04-210 phn missing machine clocks. The machine clock sensor q401 signal is missing at the phn core board. Action clear areas 4, 5, 6, and 7. (refer to the xerox docuprint 96/4635/180 ips troubleshooting guide for the procedur...

  • Page 30

    Docuprint 96/4635/180 ips messages 2-18 xerox docuprint ips messages guide 06-253 extra end of scan signal. The eos board detected more than one end of scan signal. Action select the fault list icon on the printer control console touch screen. Then touch the [clear] button to clear the codes. 06-350...

  • Page 31

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-19 06-356 eos pwb connector fault. The +5 vdc was not detected at the eos board. Action select the fault list icon on the printer control console touch screen. Then touch the [clear] button to clear the codes. 06-357 ros module ...

  • Page 32

    Docuprint 96/4635/180 ips messages 2-20 xerox docuprint ips messages guide 06-366 polygon motor fault. A polygon motor error occurred. Action select the fault list icon on the printer control console touch screen. Then touch the [clear] button to clear the codes. 06-367 card cage overtemp. The airfl...

  • Page 33

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-21 07-224 tray 2 open in print. Input tray 2 is open while the system is attempting to print. Action close input tray 2 and press continue. 07-241-1 tray 3 slow to feed position. The tray 3 elevator did not arrive at the stack h...

  • Page 34

    Docuprint 96/4635/180 ips messages 2-22 xerox docuprint ips messages guide 07-250-2 tray 4 vert trans door open in print. The feeder/stacker vertical transport door interlock switch opened during printing. Action close the tray 4 vertical transport door and retry the operation. 07-251-1 tray 3 horz ...

  • Page 35

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-23 08-103 t e jam tray 3 at pre reg q850. The trailing edge of the sheet of paper did not arrive at the preregistration sensor in time, causing a jam. Action open the inverter door and clear area 14. Open the printer right front...

  • Page 36

    Docuprint 96/4635/180 ips messages 2-24 xerox docuprint ips messages guide 08-121 l e jam at tray 2 stack force q822. The leading edge of the sheet of paper did not arrive at the stack relief sensor in time, causing a jam. Action open tray 2, clear any damaged sheets, close the tray, and retry the o...

  • Page 37

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-25 08-147 l e jam at dup takeaway roll q842. The leading edge of the sheet of paper did not arrive at the duplex takeaway roll sensor in time, causing a jam. Action open the top cover of the printer and clear area 8. Open the pr...

  • Page 38

    Docuprint 96/4635/180 ips messages 2-26 xerox docuprint ips messages guide 08-164-1 l e jam at tray 3 turn baff q853. The leading edge of the sheet of paper did not arrive at the turn baffle sensor in time, causing a jam. Action open the vertical transport door of tray 3 and clear areas 11 and 12. O...

  • Page 39

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-27 08-166-2 t e jam at tray 4 turn baff q853. The trailing edge of the sheet of paper did not arrive at the turn baffle sensor in time, causing a jam. Action open the horizontal transport door of tray 4 and clear area 13. Open t...

  • Page 40

    Docuprint 96/4635/180 ips messages 2-28 xerox docuprint ips messages guide 08-169-1 l e jam at tray 3 horz xport q854. The leading edge of the sheet of paper did not arrive at the horizontal transport sensor in time, causing a jam. Action open the horizontal transport door of tray 3, clear area 13, ...

  • Page 41

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-29 08-179 l e jam at third party cross module. There is a paper jam in the indicated area. Action clear the jam from the area using the steps provided by the system and continue the job. (refer to the xerox docuprint 96/4635/180...

  • Page 42

    Docuprint 96/4635/180 ips messages 2-30 xerox docuprint ips messages guide 08-182-2 t e jam at tray 4 takeaway rol q857. The trailing edge of the sheet of paper did not leave the tray 4 feed sensor in time, causing a jam. Action open the vertical door of the transport and clear area 11. Open tray 4,...

  • Page 43

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-31 08-185-2 l e jam at tray 4 vert xport q852. The leading edge of the sheet of paper did not arrive at the vertical transport sensor in time, causing a jam. Action open the vertical door of tray 4, clear areas 11 and 12, close ...

  • Page 44

    Docuprint 96/4635/180 ips messages 2-32 xerox docuprint ips messages guide 08-188-2 l e jam at tray 4 turn baffle q853. The leading edge of the sheet of paper did not arrive at the turn baffle sensor in time, causing a jam. Action open the vertical transport door of tray 3 and clear areas 11 and 12....

  • Page 45

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-33 08-191 sheet fed from tray 1 too narrow. The registration transport sensor dynamic width measurement of a sheet of paper fed from tray 1 is less than the expected paper width. Action open tray 1, check the paper size and repl...

  • Page 46

    Docuprint 96/4635/180 ips messages 2-34 xerox docuprint ips messages guide 08-196-2 sheet fed from tray 4 is too wide. The registration transport sensor dynamic width measurement of a sheet of paper fed from tray 4 is greater than the expected paper width. Action open tray 4, check the paper size an...

  • Page 47

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-35 08-204 l e early to regist sensor q861. The leading edge of the sheet of paper arrived at the registration transport sensor early and could not be registered correctly, causing a jam. Action open the right door of the printer...

  • Page 48

    Docuprint 96/4635/180 ips messages 2-36 xerox docuprint ips messages guide 08-217-1 tray 3 feed time below min. The feed time for tray 3 decreased by more than 88ms below the nominal feed time in standard mode. This error is logged by the system. Action no action is required. 08-217-2 tray 4 feed ti...

  • Page 49

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-37 08-227 14” transfer assist blade failure. A change in the state of the transfer assist blade sensor was not detected. This error is logged by the system. Action no action is required. 08-302 reg servo controlled failed. The r...

  • Page 50

    Docuprint 96/4635/180 ips messages 2-38 xerox docuprint ips messages guide 08-904-1 tray 3 stock does not match ui. The paper stock loaded in input tray 3 does not match the default paper stock specified for paper tray 3. Action replace the paper in input tray 3 with the correct paper stock, or chan...

  • Page 51

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-39 09-202 ac voltage out of range. The coronode ac voltage is at or outside of the acceptable limits during printing. This error is logged by the system. Action no action is required. 09-203 photoreceptor end of life. A photorec...

  • Page 52

    Docuprint 96/4635/180 ips messages 2-40 xerox docuprint ips messages guide 09-222 too short of time between belt holes. The belt hole sensor made six unsuccessful attempts to detect belt holes within the required spacing. Action open the doors of the printer, clear areas 4, 5, 6, and 7, close the do...

  • Page 53

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-41 09-326 transfer current out of range. The monitor voltage for the trans shield is less than the control voltage. Action press the [reset] button located behind the printer controller console front pullodwn cover. 09-327 detac...

  • Page 54

    Docuprint 96/4635/180 ips messages 2-42 xerox docuprint ips messages guide 09-353 fail to converge charge in dc951. The contrast potentials did not converge during dc951 setup. Action press the [reset] button located behind the printer control console front pull-down cover. 09-354 fail to set toner ...

  • Page 55

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-43 10-104 l e late to decurler sensor q1011. The sheet of paper did not arrive at the decurler sensor in time, causing a jam. Action open the printer right front door, clear areas 4 and 5, close the door, and retry the operation...

  • Page 56

    Docuprint 96/4635/180 ips messages 2-44 xerox docuprint ips messages guide 10-110 t e late at top xport sensor q1012. The trailing edge of the sheet of paper did not leave the top transport sensor in time. Action open the top cover of the printer, clear area 8, close the cover, and retry the operati...

  • Page 57

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-45 10-205 machine over voltage. The voltage to the fuser is greater than 256 vac. Action contact your service representative. 10-206 fuser transient undertemp. The temperature of the fuser has fallen at least 35 degrees below th...

  • Page 58

    Docuprint 96/4635/180 ips messages 2-46 xerox docuprint ips messages guide 10-215 fuser brake failed while camming out. The camming motor did not stop during printing. Action press the [reset] button located behind the printer control console front pull-down cover. 10-216 fuser cam motor fault. The ...

  • Page 59

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-47 11-104 t e jam at inverter entrance q1155. The trailing edge of the sheet of paper did not arrive at the inverter entrance sensor in time, causing a jam. Action open the top cover of the printer and clear area 8. Open the fro...

  • Page 60

    Docuprint 96/4635/180 ips messages 2-48 xerox docuprint ips messages guide 11-112 l e jam at prestacker q1158. The leading edge of the sheet of paper did not arrive at the prestacker sensor in time, causing a jam. Action open the top cover of stacker a and clear area 17. Open the front door of the i...

  • Page 61

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-49 11-120 stray sheet at sample tray q1157. An extra page was discarded to the sample tray. Action open the front door of the inverter and clear area 15. Remove and discard the top sheet from the sample tray. (refer to the xerox...

  • Page 62

    Docuprint 96/4635/180 ips messages 2-50 xerox docuprint ips messages guide 11-132-1 l e late to disksheet q1106a. The leading edge of the sheet of paper did not arrive at the disk sheet sensor in time, causing a jam. Action open the front door of the inverter and clear area 16. Open the top cover ab...

  • Page 63

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-51 11-138-2 l e jam at bypass xport q1107b. The leading edge of the sheet of paper did not arrive at the bypass transport sensor in time, causing a jam. Action open the top cover above stacker a and clear area 17. Open the cover...

  • Page 64

    Docuprint 96/4635/180 ips messages 2-52 xerox docuprint ips messages guide 11-141-2 t e late to bypass xport q1107b. The trailing edge of the sheet of paper did not arrive at the bypass transport sensor in time. Action open the cover above stacker a and clear area 17. Open the cover above stacker b ...

  • Page 65

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-53 11-146-1 l e jam at disk (le) sensor q1166a. The leading edge of the sheet of paper did not arrive at the disk lead edge sensor in time, causing a jam. Action open the cover above stacker a and clear area 17. Lift the top cov...

  • Page 66

    Docuprint 96/4635/180 ips messages 2-54 xerox docuprint ips messages guide 11-148-2 t e late to disk (le) sensor q1166b. The trailing edge of the sheet of paper did not arrive at the disk edge sensor in time, causing a jam. Action open the cover above stacker b and clear area 17. Lift the top cover ...

  • Page 67

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-55 11-220-1 stacker a elv failed to leave home. The elevator did not move from the original position. Action open the front doors of stacker a, check for any problems, close the doors, and retry the operation. 11-220-2 stacker b...

  • Page 68

    Docuprint 96/4635/180 ips messages 2-56 xerox docuprint ips messages guide 11-224-2 stacker b top cover interlock open. The top cover of stacker b is open while the system is attempting to print. Action open the printer top cover and clear area 8. Open the inverter and clear areas 15 and 16. Open st...

  • Page 69

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-57 11-232-1 stacker a r guide failed to exit home. The right guide home sensor did not move from the original position. Action open the top cover above stacker a, clear area 18, close the cover, and retry the operation. (refer t...

  • Page 70

    Docuprint 96/4635/180 ips messages 2-58 xerox docuprint ips messages guide 11-238-2 stacker b b guide failed to find home. The back guide home sensor did not return to the original position. Action open the top cover above stacker b and clear area 18. Close the cover and retry the operation. (refer ...

  • Page 71

    Docuprint 96/4635/180 ips messages xerox docuprint ips messages guide 2-59 11-250-2 stacker b missing 24vdc. A loss of +24 vdc was detected in the feeder/stacker module. Action contact your service representative. 11-270-2 stray sheet at purge sensor q1164b. A sheet of paper was unexpectedly deliver...

  • Page 72

    Docuprint 96/4635/180 ips messages 2-60 xerox docuprint ips messages guide 13-205 third party finisher fault during print. An error occurred with the third party finisher attached to the system. Action check the bypass transport for jams and retry the operation..

  • Page 73: Docuprint 4050, 4090, 4850,

    Xerox docuprint ips messages guide 3-1 3. 3 docuprint 4050, 4090, 4850, 4890, and 92c ips messages this chapter contains a list, in alphabetical order by code, of the messages that you may encounter while using your xerox docuprint 4050, 4090, 4850, 4890, or 92c ips. Note: throughout the messages in...

  • Page 74

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-2 xerox docuprint ips messages guide c074 tray 3 has low paper. Input tray 3 is almost out of paper. Action add paper to input tray 3. Close paper tray 3 and press the [continue] button. (refer to the xerox docuprint 4850/4890 or 92c ips guide...

  • Page 75

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-3 c081 tray 4 has low paper. Input tray 4 is almost out of paper. Action add paper to input tray 4. Close paper tray 4 and press the [continue] button. C082 tray 4 down due to unlock button being pressed. The...

  • Page 76

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-4 xerox docuprint ips messages guide c108 tray 1 feeder failed to feed sheet from stack to sfrs. The feeder did not move a sheet from the stack to the stack force relief sensor in time. Action clear feeder tray 1. Fan and add paper to tray 1. ...

  • Page 77

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-5 c150 tray 1 down due to unlock button being pressed. The unlock button was pressed and input tray 1 is lowered. Action add paper to tray 1, if necessary. Close paper tray 1 and press the [continue] button. ...

  • Page 78

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-6 xerox docuprint ips messages guide e092 vertical transport trailing edge jam. The paper from an input tray did not leave the vertical transport switch in time. Action clear the jam from areas 1 and 2 and press the [continue] button. E093 rig...

  • Page 79

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-7 e099 late arrival at post fuser switch. The paper did not arrive at the post fuser switch in time. A jam has occurred. Action clear the jam from area 4. Make sure to clear the decurler and to check the fuse...

  • Page 80

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-8 xerox docuprint ips messages guide e117 late arrival at output tray switch. The paper did not arrive at the output tray switch in time. A jam has occurred. Action clear the jam from areas 4 and 5 and press the [continue] button. If the error...

  • Page 81

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-9 e131 low toner in the system. The black dry ink supply is low. Action add black dry ink and retry the operation. (refer to the xerox docuprint 4850/4890 or 92c ips guide to performing routine maintenance fo...

  • Page 82

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-10 xerox docuprint ips messages guide e226 bottom transport leading edge jam. The paper fed from the hcf did not arrive at the bottom transport switch in time, causing a jam. Action clear the jam from area 2a and press the [continue] button. (...

  • Page 83

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-11 e248 transfer blade paper size fault. The paper size that was selected for the job, or that is available in the paper tray, is incorrect. Action install or select a larger paper size. E250 transfer blade s...

  • Page 84

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-12 xerox docuprint ips messages guide e308 toner waste container not present. The dry ink waste container is not installed. Action correctly install a dry ink waste container. (refer to the xerox docuprint 4850/4890 or 92c ips guide to perform...

  • Page 85

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-13 f007 phr lost machine clock. There is a cpm or phr board failure or a machine clock signal problem between the cpm and phr. Action obtain and discard any purged output and press the [continue] button. If t...

  • Page 86

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-14 xerox docuprint ips messages guide f040 hcfr lost pitch reset. There is a cpm, mir, or hcfr board failure or a harness problem between the cpm and mir or the phr and hfcr. Action obtain and discard any purged output and press the [continue]...

  • Page 87

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-15 f064 toner roll bias voltage out of range. There is a printer process control error. Action press the [continue] button. If the error persists, contact your service representative. F065 cleaner roll bias v...

  • Page 88

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-16 xerox docuprint ips messages guide f089 purged prints in sample tray and sample tray was the selected output. The sample tray was specified for the job but contains purged sheets that might be mixed in with your completed job. Action check ...

  • Page 89

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-17 f137 excess belt holes detected. The machine has detected too many holes on the photoreceptor belt. Action if trained to do so, replace the photoreceptor belt. Press the [continue] button. If the error per...

  • Page 90

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-18 xerox docuprint ips messages guide f158 stacker jam, late departure from stacker entry sensor or dynamic stray check fault. The paper did not leave the stacker entry in time, causing a jam. Action follow the instructions that display to loc...

  • Page 91

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-19 f164 stacker jam, late departure from bin 2 sensor. The paper did not leave bin 2 in time, causing a jam. Action follow the instructions that display to locate and clear the jam or clear the entire paper p...

  • Page 92

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-20 xerox docuprint ips messages guide f175 stacker jam, late arrival at sensor. The paper did not arrive at the stacker in time, causing a jam. Action clear the stacker tray. Open and close the stacker covers. Discard any purged output and pre...

  • Page 93

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-21 f229 finishing device full. The output bin of your third-party finishing device is full. Action remove the jobs contained in the device output bin and press the [continue] button. F231 finishing device not...

  • Page 94

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-22 xerox docuprint ips messages guide f239 bypass transport to finishing device docking fault. Indicates a jam. Action press the [continue] button. If the error persists, contact your service representative. F240 set separator sensor or soleno...

  • Page 95

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-23 f271 chopped color dc bias voltage failure. Indicates that the chopped color dc bias voltage is out of range. Action press the [continue] button. If the error persists, contact your service representative....

  • Page 96

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-24 xerox docuprint ips messages guide h014 shared line failure. The cpm cannot communicate with any of the system boards and the phr cannot communicate with the mir. In general, this indicates that there is a short in the shared line network. ...

  • Page 97

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-25 h032 fuser under temperature fault. The temperature of the fuser has fallen at least 35 degrees below the required parameters. Action press the [continue] button. If the error persists, contact your servic...

  • Page 98

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-26 xerox docuprint ips messages guide h132 no process control convergence after power up. The charge current is no longer within the system tolerance level. Action press the [continue] button. If the error persists, contact your service repres...

  • Page 99

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-27 h312 color developer housing fault. An error occurred in the color developer housing. Highlight color printing is not available. Action verify that the color developer housing unit is installed and seated ...

  • Page 100

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-28 xerox docuprint ips messages guide h333 failure of control patch generator. A patch generator error occurred. Action press the [continue] button. If the error persists, contact your service representative. H335 failure of esv1. The esv1 has...

  • Page 101

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-29 h344 convergence timeout (charge, be mode) possible photoreceptor problem. A charge convergence error occurred. The charge is at the maximum limit allowed. Action press the [continue] button. If the error ...

  • Page 102

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-30 xerox docuprint ips messages guide h353 electrostatic set-points out of range, possible massive cleaning problem. The electrostatic set points are out of the acceptable range (the black bias target voltage is greater than 1000vdc). Action p...

  • Page 103

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-31 j026 hcfr self test output failure. The hcfr board failed, an off-board problem occurred in an output device or signal line, or a loss of +24 voltage occurred. Action no action is required. If the error pe...

  • Page 104

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-32 xerox docuprint ips messages guide j147 mir self test output failure. The mir board failed, an off-board problem occurred in a phr output device or signal line, or a loss of +24 voltage occurred. Action no action is required. If the error p...

  • Page 105

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-33 j176 stacker offset fault. The stacker did not offset the output as specified for the job. The stacker mechanism may be defective. Action no action is required. If the error persists, contact your service ...

  • Page 106

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-34 xerox docuprint ips messages guide j217 4850/4890/92c ips only: interpolation overflow detected. An error occurred while converting 300 dot per inch (dpi) data to 600 dpi. Action no action is required. If the error persists, contact your se...

  • Page 107

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-35 j334 patch generator intensity at maximum. The patch generator intensity is above the required parameters. Action press the [continue] button. If the error persists, contact your service representative. J3...

  • Page 108

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-36 xerox docuprint ips messages guide l051 paper width in tray 1 changed within job. The paper width required for the print job was changed in the middle of the job and is not available in input tray 1. Action change the input configuration to...

  • Page 109

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-37 l180 stacker elevator tray full or not empty prior to size adjust or stitch capacity reached. Either the stacker tray is full, a previous job was not removed prior to sending a new job, or the maximum numb...

  • Page 110

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-38 xerox docuprint ips messages guide p022 adio terminated communication/other. The adio board terminated due to a communications failure with the core board or an adio board communication error. Diagnostic leds on the adio distinguish the typ...

  • Page 111

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-39 p194 input power to polygon driver board out of range. The polygon driver board + 15v, -15v, or the -5.2 v voltage is not within the acceptable range. Action no action is required. If the error persists, c...

  • Page 112

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-40 xerox docuprint ips messages guide p205 gwr detected sdlc communication failure. An error occurred in the printer sdlc link. Action no action is required. If the error persists, contact your service representative. P206 lost communication w...

  • Page 113

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages xerox docuprint ips messages guide 3-41 p212 ros retry fault. The printer has attempted to purge the maximum number of consecutive sheets. Action no action is required. If the error persists, contact your service representative. P214 scan system...

  • Page 114

    Docuprint 4050, 4090, 4850, 4890, and 92c ips messages 3-42 xerox docuprint ips messages guide p291 ros modulator fault. An error occurred with the raster output scanner (ros) modulator. Action press the [continue] button. If the error persists, contact your service representative. P292 ess/iot inte...

  • Page 115

    Double-click on this text from any master page and edit the definition -1 ips messages guide ../ips nps lps graphics/dpc0010a.Cgm iii ../ips nps lps graphics/dpc0474a.Cgm 1-1 ../ips nps lps graphics/dpc0334a.Eps 2-2 ../ips nps lps graphics/npsug29a.Tif @ 300 dpi 2-3 ../ips nps lps graphics/npsug29b....